Lutron Electronics Aurora Z3-1BRL Guía de configuración
1
0301916b 1/2020
Aurora
Aurora Always Ready
Smart Bulb Dimmer
Z3-1BRL
Thank you for purchasing the Aurora Always Ready Smart Bulb Dimmer from Lutron. This document will guide
you through several additional installation topics beyond those covered in the quick-start guide included with
your product.
Table of Contents
Installation Using a PhilipsRHueRBridge ...................................................................Page 2 - 4
Installation Without a Bridge (Standalone) .................................................................Page 5
Multi-location Setup without a Bridge ........................................................................Page 6
Restoring Factory Defaults ..........................................................................................Page 7
Converting from Standalone to a Bridge System.......................................................Page 8
Mounting ........................................................................................................................Page 9
Battery Replacement ....................................................................................................Page 10
Troubleshooting and LED Feedback ...........................................................................Page 11
Removing Base from Knob ..........................................................................................Page 12
Reliability Issues ...........................................................................................................Page 13
Difficulty Mounting to a Toggle Switch .......................................................................Page 14
Unpairing Bulbs / Resetting Bulbs to Factory Defaults .............................................Page 15
Installation Using an Unsupported ZigbeeRHub .......................................................Page 16
Advanced Installation Guide
2
Aurora
1Install 5Install your lights
2Search “PhilipsRHueR” and download the app
Installation Using a PhilipsRHueRBridge
4Update software
6Add your lights to the system
3
Follow the on-screen prompts to commission your
PhilipsRHueRbridge
PhilipsRHueRbridge
Update the PhilipsR HueRbridge software to the latest version.
The Aurora dimmer will not show up in the app without the latest
PhilipsR HueRbridge software.
Select "Settings" and then
select "Light setup" from the
Settings page.
Select “Search” to populate a
list of available lights.
Note: If your light is not found,
you can select “Add serial
number” and enter the serial
number; which can be found
on the individual lights.
Select "Add light."
Install your PhilipsRHueRbridge by following the manufacturer's
instructions.
Screw in and power on your HueRlamps.
b
c
d
a
NOTE: Only compatible with PhilipsRHueRsquare-shape bridge
V2. Not compatible with round-shape Bridge V1.
3
Aurora
Installation Using a PhilipsRHueRBridge (continued)
7Create and assign rooms 8Add Aurora dimmer
Settings > Accessory Setup > Add Accessory >
Friends of HueRSwitch
Create rooms and assign your lights to the appropriate room.
Select "Settings" and then
select "Accessory setup" from
the Settings page.
Select "Settings" and then
select "Rooms & zones" from
the Settings page.
First name your room at the
top, then select the lights that
you wish to add to the room.
Then save your settings.
Select "Create new."
Select "Create new room."
Select "Friends of Hue switch." Select "Lutron Aurora" from the
list of Friends of Hue switches.
Select "Add accessory."
Add your Aurora dimmer to the system and select the room you
want the dimmer to control.
b
c
c
d
e
f
a
a
d
e
b
4
Aurora
Installation Using a PhilipsRHueRBridge (continued)
8Add Aurora dimmer (continued)
As indicated on the app
screen, quickly double-press
the center button on the Aurora
to begin connecting.
Either select "Done" to
complete the setup, or select
"Change settings" if you want
to change the scene which
will be activated by the Aurora
dimmer.
From the list of rooms that you
have previously created, select
the room you want the Aurora
dimmer to control.
Select the icon under the
header "Press" to pick from a
list of scenes.
Select your desired scene, or
choose to have the dimmer
recall your last light level. Save
your settings.
f
gb
a
h
9Select scene for dimmer to activate (Optional)
5
Aurora
Installation Without a Bridge (Standalone)
1Turn the desired lights OFF and then back ON
2 Connect the light
a
b
c
<4 in (10 cm)
63
6 sec +3 sec
NOTE: This allows the lights to connect with controls for about
15 minutes.
NOTE: If you want more than one Aurora dimmer to control the
same set of lights, see the Multi-location Setup Without a
Bridge section on the next page.
While holding the Aurora dimmer as close as possible to
the bulb, press and hold the button on the Aurora dimmer.
The LED on the Aurora dimmer will begin to blink; continue
holding for approximately 9 seconds.
After approximately 6 seconds, the selected light will flash to
indicate which one you are connecting. If the light is correct,
continue holding the button down. If it is the incorrect light,
release the button and start over. Try holding the Aurora
dimmer closer to the light you are trying to connect.
Continue holding the button until the LED on the Aurora
dimmer begins to rapidly flash (should be about 3 seconds
after light flashed). When the LED stops flashing, Aurora is
ready for use.
Repeat steps a–b for all additional lights you wish to control
with your Aurora dimmer.
NOTE: When pairing an Aurora dimmer directly to multiple PhilipsR
HueRbulbs (standalone), it may be easier to pair each of the bulbs
one at a time in a table lamp before installing the bulbs in their
final location so that you are able to get the Aurora dimmer close
enough to the bulb. Additionally, having only one bulb powered
at a time will ensure that the desired bulb is paired to your Aurora
dimmer.
6
Aurora
Multi-location Setup without a Bridge
1Connect lights to first unit
2Pair units to each other
3Connect lights to second unit
Hold both units so they are as close together as possible.
Simultaneously press & hold the button on both units until the LED
on both Aurora dimmers flash rapidly; approx. 12 seconds.
NOTE: It is important to connect the Aurora dimmers to each
other. If you do not, the second Aurora dimmer will steal the lights
away from the first Aurora dimmer when they are connected to the
second unit. To add more than two Aurora dimmers, continue to
connect additional factory-new or factory-default Aurora dimmers
to the first unit.
On the second unit, repeat Step 1 for all lights that the dimmer
will control.
a
b
c
d
While holding the Aurora dimmer as close as possible to
the light, press and hold the button on the Aurora dimmer.
The LED on the Aurora dimmer will begin to blink, continue
holding for approximately 9 seconds.
After approximately 6 seconds, the light will flash to indicate
which one you are connecting. If the light is correct,
continue holding the button down. If it is the incorrect light,
release the button and start over. Try holding the Aurora
dimmer closer to the light you are trying to connect.
Continue holding the button until the LED on the Aurora
dimmer begins to rapidly flash.
Repeat steps a–c for all additional lights you wish to control
with your Aurora dimmer.
Multiple Aurora dimmers can be used to control the same group
of lights in standalone mode. Special steps need to be taken to
allow more than one Aurora dimmer to control the same set of
lights. Without following these steps, programming a second
Aurora dimmer to lights which have previously been connected
to another Aurora dimmer, will result in the second Aurora
dimmer stealing the lights away from the first Aurora dimmer.
Please follow the steps below carefully.
NOTE: Up to 6 Aurora dimmers can be programmed to control
the same set of lights in a standalone system.
<4 in (10 cm)
63
6 sec +3 sec
<4 in (10 cm)
63
6 sec +3 sec
7
Aurora
Restoring Factory Defaults
1Tap button quickly 3x
2
On the third tap, continue holding until LED blinks
(6 seconds)
3
Once LED is blinking quickly tap button 3x again.
LED will flash rapidly to show success.
66 sec
3x
Follow the instructions below to erase device settings (including
light or bridge pairings) and return to factory defaults.
3x
8
Aurora
Converting from Standalone to a Bridge System
NOTE: Please see the previous section for how to Restore Factory
Defaults to your Aurora dimmer.
NOTE: The lights that were previously connected directly to an
Aurora dimmer will not be automatically discovered by the app.
These can be added to the system by manually typing the serial
number on the light into the app.
If you previously had an Aurora dimmer connected to a lamp
without a bridge, and you wish to add it to a bridge system,
please follow the steps below, or reset the lights to factory
defaults as described on page 15.
1Restore the Aurora dimmer to the factory defaults
2
Add the Aurora dimmer by following the prompts on
the app (see page 2)
9
Aurora
1 Make sure light is ON
2
While the light is ON, place base over the toggle
switch as shown
3 Install mounting base
Mounting
4Attach knob to mounting base
OR
AND
While holding the base against the wallplate, use a Phillips
head screwdriver to turn the screw until the clamp has securely
attached to the toggle switch.
Align opening with
toggle switch
Snap knob on to the mounting base.
NOTE: To mount the knob on the base, it is important to align the
knob properly. The cutout in the back of the product is made to
accommodate your toggle switch. If the knob doesn't snap on
easily, double check the alignment.
NOTE: If there is more than one switch which controls a set
of lights, some of the switches on that circuit will be "up"
in the On position, and some will be "down" in the position
which usually indicates the switch is Off. Rotate the base
until it is as shown above.
CORRECT
INCORRECT
10
Aurora
Battery Replacement
Using a #1 Phillips head
screwdriver, loosen the screw in
the battery door. Unscrew just
enough that the battery door
comes loose but the screw
remains attached.
Place a rubber band between your finger and the battery to
improve your grip.
Stick a piece of scotch tape to the battery and pull to remove.
Pull down gently to open the
battery door.
Slide the battery straight up
to remove.
1 Pull knob away from base
Option 1
Option 2
2 Loosen screw and open battery door
3 Slide to remove/install
WARNING: Risk of fire, explosion, and burns. May
result in serious injury or death. DO NOT recharge,
disassemble, crush, puncture, heat above 212 °F (100
°C) or incinerate the battery.
The battery in this device contains Perchlorate material,
special handling may apply. For more information, visit
www.dtsc.ca.gov/hazardouswaste/perchlorate
+
Grab the outside of
the knob and pull it
straight away from
the mounting base to
remove.
Tips for Removing the Battery
Selecting a Battery
NOTE: Due to natural oils on your finger, it can be difficult to slide
the battery out for removal. Many common household items
can help.
The Aurora dimmer is designed and tested with Panasonic
CR2032 batteries. For the best performance, it is recommended
that batteries are replaced using the same Panasonic battery.
Otros manuales para Aurora Z3-1BRL
1
Tabla de contenidos
Otros manuales de Automatización del hogar de Lutron Electronics
Lutron Electronics
Lutron Electronics Caseta Pico Paddle Remote Manual de usuario
Lutron Electronics
Lutron Electronics Energi TriPak Family PowPak Fixture Controls Manual de usuario
Lutron Electronics
Lutron Electronics Caseta Diva Smart Dimmer Manual de usuario
Lutron Electronics
Lutron Electronics Maestro IR MIR-600 Manual de usuario
Lutron Electronics
Lutron Electronics Caseta Pico PD-6WCL Manual de usuario
Lutron Electronics
Lutron Electronics RadioRA2 RRD-H2RLD Manual de usuario
Lutron Electronics
Lutron Electronics RadioRA RALK-2W-SD Manual de usuario
