Lutron Electronics SeeTouch guestroom solutions Manual de usuario

seeTouch®guestroom solutions

Installation Guide Please Read

IMPORTANT:

•Lightingcontrolsmustbeinstalledbyaqualifiedelectricianinaccordancewithallapplicableregulations.

WARNING: Shock Hazard. Mayresultindeathorseriousinjury. DONOTWIRELIVE!Interrupt

powerviacircuitbreakerbeforewiringandservicing.

•Alwaysturnoffcircuitbreaker/MCBorremovemainfusefrompowerlinebeforedoinganywork.

•Toreducetheriskofoverheatingandpossibledamagetootherequipment,themodulemustbemounted

asshown.Failuretoprovideadequatespaceforcoolingmayresultinoverheatingandvoidthewarranty.

•Modulehumsslightlyduringoperationandtheinternalrelayclickswhenthecircuitisturnedonandoff.

Chooseaninstallationlocationwherethesesoundsareacceptable.

•Lightingcontrolsaredesignedforcommercialindooruseonly.

•ThiscontrolusesPELVwiringmethods.Checkwithyourlocalelectricalinspectorforcompliancewith

nationalandlocalcodesandwiringpractices.

230 V 50/60 Hz 8,75 A (40 – 350 W per zone)

24 V 200 mA (Panels with a power supply only)

2 seeTouch®guestroom solutions

seeTouch®guestroom solutions 3

Table of Contents

Overview

Panel Details

Poweredbyaprecision-engineereddimmingpanel,thenewseeTouch®guestroomsolutionisacost-effective,

simple-to-installlightingcontrolsolutionforhotelguestrooms.

Description

• Allowssetupoflightingscenesandshadepresetsusingbuttonsonthepanel.

• Controlsmanylightsourcetypesdirectlyandothersusingpowerinterfaces.

• Providesindividualcontroloflightsources.

• Includesbuilt-inastronomictimeclock.

• Includesonecontactclosureinputand24V powerforoccupantsensorsorotherbuildingmanagement

systems.

• Includescommunicationlinkforseamlessintegrationoflights,motorizedwindowtreatments,andcontrolstations.

• CompatiblewithallLutron®QSsystemcomponents.

Contents

Overview 3

Dimensions and Mounting 4

Panel Wiring 5

Control Unit Wiring 6

Wallstation Installation 7

Start-Up Procedure 8

Ethernet Wiring 9

Contact Closure Wiring 10

Warranty 11

Contact Information 12

4 seeTouch®guestroom solutions

Dimensions

Mounting

Attention Contractor!

Pleaseuseprovidedknockoutsfor

inputmainswiringconduit.Drilling

additionalholesinenclosurecould

damageelectroniccomponents

insidethepanel.

Alldimensionsinmm(in)

Notes

• Forindooruseonly.

• Consultdimensionsdrawingabove

forpanelsize,conduitknockouts,and

mountingholes.

• Mountwhereambienttemperatureis

0to40°C(32to104°F).

• Reinforcewallstructureforweightand

localcodesasnecessary.

• Mountpanelsoline/mainsvoltage

wiringisatleast1,8m(6ft)fromsound

orelectronicequipmentandwiring.

• Lutronrecommendsusing6mm

(0,25in)mountingbolts.

• Allow32mm(1,25in)clearanceon

eachsideofpanelforcover.

• Allow63mm(2,5in)between

enclosures.

• Panelweight:8kg(18lbs)

• Panelshouldnotbemountedinside

anotherelectricalencloser.

Top View

22 (0,88)

337 (13,25)

286 (11,25)

(3,14)

86 (3,39)

with cover

(2,93)

8 (0,31)

337 (13,25)

(1,0)

235

(9,25)

235

(9,25)

191

(7,5)

Front ViewLeft Side

View

Right Side

View

Bottom View

= Knockouts

= Do Not Use

These Knockouts

Front View

Mains

Wiring

No PELV

PELV

Wiring Only

Side

View

seeTouch®guestroom solutions 5

Panel Wiring Instructions

WARNING: Shock Hazard. Turn power OFF to all circuits before installing any part of the

dimming system. Wiring with the power on can result in death or serious personal injury.

NOTICE: Verify that the panel is fed from the correct voltage. A feed miswire or loss of a feed

neutral can cause damage to the equipment.

1.Pull dedicated feeds.Eachpanelrequiresa10Adedicatedfeed.

2.Power and control wires must be run in separate conduit or raceways.Runindividualneutralsforinput

andeachloadcircuit.

3.Use 10 A breakers. Do not exceed 2,1 kW per 10 A circuit. (350 W by 6 zones for 2,1 kW max)

4.Connect load wires to terminals DL1-DL6. Connect all load neutrals for each panel to the neutral

terminals (N).

Load Types

 Thepanelcancontrolincandescent,halogen(tungsten),magneticlow-voltage,andneon/coldcathodeload

types.Electroniclow-voltageandfluorescentloadtypescanbecontrolledwithanappropriateinterface.

• Notallzonesneedtobeconnected;however,connectedzonesmusthavealoadofatleast40W.

• Nozonemaybeloadedwithmorethan350W.Maximumloadcapacityforeachpanelis2,1kW.

• Panelmustnotcarrymorethan8,75Aoftotallightingload.

• AllElectronicLow-Voltage(ELV)lightingusedwiththeElectronicLow-VoltageInterfacemustberatedfor

reverse phase control dimming.BeforeinstallinganELVlightsource,verifywiththemanufacturerthattheir

transformercanbedimmed.Whendimming,anElectronicLow-VoltageInterfaceMUSTbeusedwiththepanel.

Wiring Note

 UsethebottomrightknockoutswhenpullingPELVwiresintothemainpanel,allotherknockoutsfor

non-PELVuse.

1.Strip25mm(1in)ofinsulationfromthePELVcable.

2.Strip9mm(3/8in)ofinsulationfromeachwire.

3.ConnectthePELVwirestothePELVterminalblock.Makesurenobarewireisexposedaftermaking

connections.

4.Therecommendedinstallationtorqueis0,4N•m(3,5in-lb)forPELVconnections.

(L) 220-240 V

( ) Ground / Earth

Occ Sensors

OCC SIG

24 V

OCC COM

Load

MUX

+24 V

COM

(N) Neutral

6 seeTouch®guestroom solutions

Control Unit Wiring

PELV System Wiring

• SystemcommunicationusesPELVwiring.

• Wiringcanbedaisy-chainedorT-tapped.

• Wiringmustberunseparatelyfromline/mainsvoltage.

• PELVwiringlinkrequires:

 –Two1,0mm2(18AWG)conductorsforcontrolpower.

 –Onetwisted,shieldedpairof0,5mm2(22AWG)fordatalink.

 –AvailablefromLutron,P/NGRX-CBL-346S;checkcompatibilityinyourarea.

• Totallengthofcontrollinkmustnotexceed610m(2000ft).

• Upto10wallstationscanbepoweredfromeachPanelwithapowersupply(seemodeldescriptionsfordetails).

1234

Panel #1

Non-RF Panel

(with power supply)

Panels with power supplies can power up to 10 wallstations and cannot

have terminal #2 tied to other panels with power supplies. As shown

in diagram.

* Pin 2 from Panel #2 powers wallstation but does not go to other panels.

Panel #2*

Non-RF Panel

(with power supply)

Panel #3

RF Panel

(NO power supply)

Panel #4

Non-RF Panel

(with power supply)

1234

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

C B A

4 3 2 1

Panel Wiring Example

Daisy-Chain Wiring Example

Panel

T-Tap Wiring Example

Panel

seeTouch®guestroom solutions 7

Wallstation Wiring: Panel with up to Ten Wallstation Controls

 EachpanelwithapowersupplycanpoweruptotenWallstationControls.Ifyouneedtopowermorethanten

WallstationControlsfromonepanel,installanexternal24V powersupply.

 Maximumof300m(1000ft)betweentheControlUnitandthesecondWallstation.Forlongerdistances,use

anexternalPELVrated24V powersupply.

IMPORTANT WIRING NOTE:

 Daisy-chaintheterminal1,terminal2,terminal3,andterminal4connectionstothepaneland

WallstationControls.

Note:DonotallowPELVwirestocontactline/mainswires.

Wallstation Installation

Control Station Device (CSD) Link Wiring

• Uselow-voltagePELVwiringtoconnectWallstations

tothepanellink.

• Makeconnectionsinsidethewallboxorinaswitch/

junctionboxwithamaximumwirelengthof2,5m

(8ft)fromthelinktotheWallstation.

• Strip9mm(3/8in)insulationfrombothtwistedpairs

inthewallbox.

• Two1,0mm2(18AWG)conductorsforcommon

(terminal1)and24V (terminal2).Thesewillnotfit

interminals.Connectasshown.

• Oneshielded,twistedpair0,5mm2(22AWG)for

datalink(terminals3and4).

• ConnectDrain/Shieldasshown.Donotconnect

toGround(Earth)orWallstation.Connectthebare

drainwiresandcutofftheoutsideshield.

Note: SomeWallstationshavea“D”terminalfor

Drain.TheDrain/Shieldwiremaybeconnectedto

thisterminal.

4 3 2 1

C B A

PELV(Class2:USA)

Controlwiring

(2)1,0mm2(18AWG)

1:Common

2:24V

(2)1,0mm2

(18AWG)

(2)1,0mm2

(18AWG)

DataLink-(1)twisted,shieldedpair

0,5mm2(22AWG)

3:MUX

4:MUX

RearofWallstation

Contact Closure Input Wiring

• UsePELV/SELVwiringtoconnectthecontact

closureinputstotheWallstation.

• Inputsmustbedrycontactclosureorground

referencedsolid-stateoutputs.

• Wallstationismiswireprotectedupto36V.

• Outputsmuststayintheclosedoropenstatesfor

atleast40msinordertoberecognizedbythe

Wallstation.

4 3 2 1

C B A

B:Input2

A:Input1

C:Common

(3)1,0mm2

(18AWG)

RearofWallstation

8 seeTouch®guestroom solutions

Wallstation Installation (continued)

1.Mountwallboxwithappropriatedepth.

2.Strip9mm(3/8in)insulationfrombothtwisted

pairsinthewallbox.

Start-up Procedure

Check Load Circuits

1.Makesurethefactory-installedbypassjumper(s)arestillinplacebetweentheL(Live)andDL(DimmerLoad)

terminals.Replacepanelcover.Turncircuitbreakeron.

2.ChecktheinputcurrenttotheL(Live)terminalwitha“clamp-on”typecurrentprobe.Thecurrentprobe

shouldmeasurenomorethan8,75A.

3.TurnloadsONforatleasttenminutes.Ifcircuitbreakertrips,turnpowerOFF,thenlocateandcorrectmiswire

oroverload.

Check Panel

1.WithpowerOFF,makesureallcontrolwiringiscorrect.Replacepanelcover.Turncircuitbreakeron.

2.Pushbuttonsonwallstationcontrol.Thelightingshouldgotofull,butthecontrolindicatorlightsshouldgo

on/off.

Remove Bypass Jumpers

1.TurnpowerOFF.

2.Removetheloadcircuitbypassjumperfromthecontrolpanel.

3.TurnpowerON.ChangethescenebuttonsontheGrafikEye®QStomakesuretheyadjustthelightlevel.

seeTouch®guestroom solutions 9

RS232/Ethernet Wiring

WARNING: Shock Hazard. Mayresultin

deathorseriousinjury. DONOTWIRELIVE!

Interruptpowerviacircuitbreakerbefore

wiringandservicing.

ForEthernetlink,useCAT5cable(notincluded)to

connecttoauxiliaryequipment.Maximumlength

forCAT5cableis100m(328ft).TheEthernet

LinkLEDwilllightcontinuouslywhenthelinkis

presentandwillflashwhenthereislinkactivity.

AdditionalEthernetnetworkequipmentandcables

notprovided.

Network Connections

DIP

Switches LED1:Power

LED2,3:Unused

LED4:RS232LinkTx

LED5:RS232LinkRx

LED6:DataLinkTx

LED7:DataLinkRx

DataLink

(tocontrol

units,

processors,

and

wallstations)

RS232

Link

Ethernet

Link

Ethernet Interface Wiring

RS232 Link Wiring

• Standard9-pinserialconnectorplugsintoRS232

equipment,andtoEthernetInterface.

• Mustbe15m(50ft)orless.

Ethernet Link Wiring

•StandardCAT5cableconnectsEthernetInterface

toPC,router,orotherEthernetsource.

•Nocrossovercableneeded.

•Shouldnotexceed100m(328ft).

•Ethernetnetworkandcablenotprovided.

RS232 Signals

Signals Pinon9-pinCable

Com 5

TxD 3

RxD 2

10 seeTouch®guestroom solutions

Contact Closure Wiring

IO Connections

DIP switches

LED 1: CCO 1

LED 2: CCO 2

LED 3: CCO 3

LED 4: CCO 4

LED 5: CCO 5

LED 6: Unused

LED 7: Status

Notes: CCO LED is ON when CCO NO (normally

open contact) is closed.

Status LED blinks once per second

during normal operation

CCO and CCI connectors hold one

0,08 - 1,5 mm2(28 - 16 AWG) wire

NC = Normally closed

NO = Normally open

Data Link (to wallstations)

3: MUX

1: Common

4: MUX

CCO 1 NC

CCO 1 NO

1-2 COM

CCO 2 NC

CCO 2 NO

CCO 3 NC

CCO 3 NO

3-4 COM

CCO 4 NC

CCO 4 NO

CCO 5 NC

CCO 5 NO

5 COM

CCI 1

CCI 2

CCI 3

CCI 4

CCI 5

COM

Contact Closure Outputs Contact

Closure

Inputs

1234567

Program button

2: 24 V

DIP switches

LED 1: CCO 1

LED 2: CCO 2

LED 3: CCO 3

LED 4: CCO 4

LED 5: CCO 5

LED 6: Unused

LED 7: Status

Notes: CCO LED is ON when CCO NO (normally

open contact) is closed.

Status LED blinks once per second

during normal operation

CCO and CCI connectors hold one

0,08 - 1,5 mm2(28 - 16 AWG) wire

NC = Normally closed

NO = Normally open

Data Link (to wallstations)

3: MUX

1: Common

4: MUX

CCO 1 NC

CCO 1 NO

1-2 COM

CCO 2 NC

CCO 2 NO

CCO 3 NC

CCO 3 NO

3-4 COM

CCO 4 NC

CCO 4 NO

CCO 5 NC

CCO 5 NO

5 COM

CCI 1

CCI 2

CCI 3

CCI 4

CCI 5

COM

Contact Closure Outputs Contact

Closure

Inputs

1234567

Program button

2: 24 V

Contact Closure Ratings

Five Input Terminals

• Acceptsmaintainedinputsandmomentaryinputswith40ms

minimumpulsetimes.

• Off-stateleakagecurrentmustbelessthan100μA.

• Opencircuitvoltage:24V maximum.

• Inputsmustbedrycontactclosure,solidstate,opencollector,

oractive-low(NPN)/activehigh(PNP)output.

 –OpencollectorNPNoractive-lowon-statevoltagemustbe

lessthan2Vandsink3,0mA.

 –OpencollectorPNPoractive-highon-statevoltagemustbe

greaterthan12Vandsource3,0mA.

• Lutronrecommendsamaximumof3occupantsensorswired

inparallelperinput.

Five Output Terminals

• Provideselectablemaintainedormomentary(250ms)outputs.

• Theinterfaceisnotratedtocontrolunclamped,inductiveloads.

Inductiveloadsinclude,butarenotlimitedto,relays,solenoids,

andmotors.Tocontrolthesetypesofequipment,aflyback

diodemustbeused(DCvoltagesonly).Seediagrambelow.

• Outputrelaysarenon-latching(i.e.ifrelaysareclosedand

powerislost,relayswillopen).

Supply

Voltage

0–24V

Resistive

Load

1,0A

0,5A

24V 

max.

Inductive

Load

Flyback

Diode

(requiredfor

inductive

loads)

IO

Output

Output Ratings

NO NC

COM

Tabla de contenidos

Otros manuales de Unidad de control de Lutron Electronics

Lutron Electronics

Lutron Electronics AuroRA ARMC-5T Manual de uso y cuidado

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manual de usuario

Lutron Electronics

Lutron Electronics GRAFIK Eye Architrave GRX-4SLB-DW Manual de usuario

Lutron Electronics

Lutron Electronics QS Timeclock Instrucciones de funcionamiento

Lutron Electronics

Lutron Electronics Vive Series Manual de usuario

Lutron Electronics

Lutron Electronics PowPak FC-SENSOR Manual de usuario

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRN-6PCE Instrucciones de funcionamiento

Lutron Electronics

Lutron Electronics Vive PowPak Manual de usuario

Lutron Electronics

Lutron Electronics PowPak RMJ-5R-DV-B Manual de usuario

Lutron Electronics

Lutron Electronics Maestro Wireless MRF2-3PD-1 Manual de usuario

Lutron Electronics

Lutron Electronics PowPak RMJS-16R-DV-B Manual de usuario

Lutron Electronics

Lutron Electronics Maestro Wireless Pico Series Manual de usuario

Lutron Electronics

Lutron Electronics Pico QSR4P-3R Manual de usuario

Lutron Electronics

Lutron Electronics GRAFIK Eye QSGRJ-3P Instrucciones de funcionamiento

Lutron Electronics

Lutron Electronics PowPak RMJS-CCO1-24-B Manual de usuario

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Manual de usuario

Lutron Electronics

Lutron Electronics Grafik Eye GRX-4000 Series Instrucciones de montaje

Lutron Electronics

Lutron Electronics Energi Savr Node Manual de usuario

Lutron Electronics

Lutron Electronics PowPak Energi TriPak Series Manual de usuario

Lutron Electronics

Lutron Electronics Stanza SZ-2B Manual de usuario

Lutron Electronics

Lutron Electronics AYFSQ-F Manual de usuario

Lutron Electronics

Lutron Electronics GFS-5E Manual de usuario

Lutron Electronics

Lutron Electronics PowPak RMK-CCO1-24-B Manual de usuario

Lutron Electronics

Lutron Electronics TriPak Series Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario

Lutron Electronics seeTouch guestroom solutions Manual de usuario

Manuales populares de Unidad de control de otras marcas