Lucent Technologies Definity 8434DX Manual de usuario

DEFINITY®Enterprise Communications Server

Generic 2 and System 85

8434DX Voice Terminal

Quick Reference

555-104-768

Comcode 107985517

Refer to the procedures on this card to use the

features on your 8434DX voice terminal. The features

here are listed in alphabetical order. In the spaces

provided, write in the feature access codes for your

system. For more information about any of these

features, see your system manager or refer to the

DEFINITY

Generic 2 and System 85

8434DX Voice

Terminal User’s Guide

, 555-104-767.

USING THE SOFTKEYS

You can display any of the softkey featuresby pressing

and then the softkey below the feature

abbreviation. If the feature you want to use is not on

the bottom line of the screen, press or

until you see the feature you wish to access.

When the feature is active, an arrow appears above

the feature. (However, ifthe feature requires you to dial

a telephone number or extension, such as Call

Forwarding, you will temporarily see the digits you are

dialing, rather than the arrow, above the feature

name.)

CANCELLING FEATURES

In order to cancel or deactivate features, such as

cancelling a LWC message or deactivating Send All

Calls, you must be off-hook.

8434dx.qref.def2.fm Page 1 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

all-guides.com

To program/reprogram an AD button

1Pick up handset.

NOTE: For speakerphone users, press a call

appearance button or press .

2Press softkey below Prog

or Press

or Dial AD Program access code _________.

3Press selected AD button.

4Dial outside number, extension, or feature access

code you want to store (up to 24 digits).

5Press selected AD button again.

6Repeat Steps 3 through 5 to program additional

buttons.

7Hang up.

To place an AD call

1Pick up handset or press .

2Press selected AD button.

To program/reprogram an outside number,

extension, or feature access code into a personal

list

1Pick up handset.

NOTE: For speakerphone users, press a call

appearance button or press .

2Press softkey below Prog

or Press

or Dial AD Program access code ________.

3Press

or Dial AD Program access code ________.

4Dial list item (1, 2, 3...).

5Dial number you want to store (up to 24 digits).

NOTE: You may also be able touse the softkeysto

add special functions such as Pause, Mark, Wait,

or Suppress into the programmed telephone

numbers.

6Press .

7Repeat Steps 4 through 6 to program additional

items on the same list.

8Hang up.

ABBREVIATED DIALING (AD)

Speaker

Program

Speaker

Program

Personal List

8434dx.qref.def2.fm Page 2 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To place a call using an AD list button or access

code

1Press or or

or Dial appropriate AD List access code:

•Personal __________

•Group __________

•System __________

2Dial desired list item (1, 2, 3...).

To automatically place another call to an extension

that is frequently busy

1During call attempt press softkey below AutCB

or Press

or Dial Automatic Callback access code before call

attempt ________.

2Hang up.

•You hear a 3-burst priority ring when both you

and the called extension are idle.

Pick up handset to be connected to call.

To cancel Automatic Callback

1While off-hook, press softkey below AutCB again

or Press again

or Dial Automatic Callback cancel code ________.

To answer a bridged call

1Presscall appearance button ofbridged call and lift

handset or press .

NOTE: If you terminal has Ringing Appearance

Preference, just lift the handset or press .

To prevent other bridged terminals from entering a

call (on a per call basis)

1Press the softkey below Excl while active on a call

or Press while connected to the call.

NOTE: Pressing the softkey below Excl or

pressing again reactivates bridging.

AUTOMATIC CALLBACK

BRIDGING/MANUAL EXCLUSION

Pers List

Grp List Sys List

AutoCallBk

Speaker

Excl xxxxx

8434dx.qref.def2.fm Page 3 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To answer a call for a coworker for whom you are a

coverage point

1Press call appearance button of the incoming call

when ringing begins or green light flashes.

To talk privately with a coworker after answering a

redirected call

1Press .

•Call is put on hold.

2Press the softkey below Cnslt

or Press

or Dial coworker’s extension.

3Discuss call, if appropriate.

4If coworker is not available, press the call

appearance button next to the fluttering light to

reconnect to the call

or Press again to send call to coworker

or Press to make it a 3-party call.

NOTE: You may have either Call Forwarding — Follow

Me or Call Forwarding — Busy/Don’t Answer. Ask your

system manager if you can use either of these Call

Forwarding features.

To temporarily redirect all calls to an extension or

outside number

1Press softkey below CFrwd (for display users who

have the Call Forwarding — Follow Me feature)

or Press

or Dial Call Forward access code _______.

2Dial extension or number where calls will be sent.

3Hang up.

To cancel Call Forwarding

1While off-hook, press softkey below CFrwd

(for display users who have the Call Forwarding —

Follow Me feature)

or Press again

or Dial Call Forward cancel code _______.

CALL COVERAGE/CONSULT

CALL FORWARDING

Transfer

Consult

Transfer

Conf

Call Fwd

8434dx.qref.def2.fm Page 4 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To park a call at your extension (for retrieval at any

extension)

1Press .

2Dial Call Park access code _______.

3Dial Call Park zone number.

4Dial an idle Answer-Back channel number.

5Press .

6Press again.

7Hang up.

To retrieve a parked call from any extension

1Dial Answer Back access code _______.

2Dial channel number where call is parked.

To answer a call placed to a member of your

pickup group

1Press

or Dial Call Pickup access code ________.

To add another party to a call (for a total of

up to 3 parties)

1Press .

2Dial number of new party and wait for answer or

press call appearance of held call.

3Press again.

To drop the last party added to a conference call

1Press .

When you are ready to leave Display or Softkey

Mode and return to Normal (call-handling) Mode

1Press .

CALL PARK

CALL PICKUP

CONFERENCE

EXIT/NORMAL (display feature)

Transfer

Recall

Transfer

Call Pickup

Conf

Drop

Exit

8434dx.qref.def2.fm Page 5 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To put a call on hold

1Press .

To answer a new call while active on another

1Press .

2Press call appearance button of incoming call.

To return to held call

1Press call appearance button of held call.

To see who is calling while on a call

1Press .

•Call source is shown on display.

2Press to return to display for present call.

To make a call to your predetermined Automatic

Intercom partner

1While off-hook, press .

To dial a call to a member of your Dial Intercom

group

1While off-hook, press .

2Dial the group member’s 1- or 2-digit code.

To answer any intercom call

1Pick up the handset and press .

2If you are active on another call, first press ,

and then press the button next to the

flashing light.

To automatically redial the last number you dialed

1Press

or Dial Last Number Dialed access code _______.

HOLD

INSPECT (display feature)

INTERCOM (AUTOMATIC/DIAL)

LAST NUMBER DIALED

Hold

Inspect

Exit

Icom Auto xxx

Icom Dial xxx

Icom

Hold

Icom

LastDialed

8434dx.qref.def2.fm Page 6 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

all-guides.com

To leave a message after dialing an extension

1Press softkey below LWC

or Press before hanging up your handset.

To leave a message without ringing an extension

1Press softkey below LWC

or Press

or Dial Leave Word Calling access code _______.

2Dial extension.

3Hang up.

To cancel a Leave Word Calling message

1While off-hook press the softkey below CnLWC

or Press

or Dial Leave Word Calling cancel code _______.

2Dial extension.

To place a priority call (3-burst ring)

1Press the softkey below PCall

Press

or Dial Priority Calling access code _______.

2Dial extension.

NOTE: You can use this feature only if the

Reset

Spkr

label appears under the button.

To adjust the speakerphone to the surrounding

room acoustics

1While on-hook, press and then press

•You hear a series of tones.

LEAVE WORD CALLING (LWC)

PRIORITY CALLING

RESET SPEAKERPHONE

LWC

Cancel LWC

Priority

Speaker

Shift

Speaker

8434dx.qref.def2.fm Page 7 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To select a personalized ring

1If your 8434DX has a button, press

and then press ;

if your 8434DX has a button, press .

•Current ringing pattern plays.

2To cycle through all eight ring patterns:

if your 8434DX has a button, continue to

press (and then release) to hear each

subsequent pattern;

if your 8434DX has a button, continue to

press (and then release) to hear each new

pattern.

NOTE: In either case, you can also press or

to cycle through the eight ringing patterns.

3To set the selected ringing pattern:

if your 8434DX has a button, press

when you hear the desired ring pattern;

if your 8434DX has a button, don’t press

anymore. You will hear the selected ringing

pattern two more times, and then it will be

automatically saved.

•You hear confirmation tone.

To adjust ringer volume if necessary

(speaker is

not

active)

1To raise the volume, press the right half of the

Volume control button labeled ;

to lower the volume, press the left half of the

Volume control button labeled .

To send all calls (except priority calls)

immediately to coverage

1Press

or Dial Send All Calls access code _______.

To cancel Send All Calls

1While off-hook, press again

or Dial Send All Calls cancel code _______.

SELECT RING (and RINGER VOLUME)

SEND ALL CALLS

Shift Shift

Hold Ring Ring

ShiftHold

Ring

Shift Shift

Ring

Send Calls

8434dx.qref.def2.fm Page 8 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

NOTE: To use this feature, your voice terminal must

be set for the Speakerphone (speak and listen)

feature.

To place/answer a call without lifting the handset,

or to use speakerphone with any feature

1Press .

2Place or answer call, or access selected feature.

3Adjust speakerphone volume if necessary:

To raise the volume, press the right half of the

Volume control button labeled ; to lower the

volume, press the left half of the Volume control

button labeled .

To prevent the other party from hearing you

1Press .

•Red Mute light goes on.

2Press again to resume talking to party.

•Red Mute light goes off.

To change from speakerphone to handset

1Pick up handset and talk.

To change from handset to speakerphone

1Press .

2Hang up handset.

To end a speakerphone call

1Press again to hang up.

To test the lights and the display on your voice

terminal

1Press and hold down .

•Green Test light goes on.

•Button lightsgo on in two separate groups,and

all display segments fill in.

2To end test, release .

SPEAKERPHONE

TEST

Speaker

Mute

Speaker

Test

8434dx.qref.def2.fm Page 9 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

To see date and time

1Press softkey below TmDay

or Press .

To see elapsed time

1To start timer, press and the softkey

below Timer

or Press .

2To stop timer, press and the softkey

below Timer

or Press again.

To send present call to another extension or

outside number

1Press .

2Dial number where call is to be transferred.

3Press again.

4Hang up.

Prepared by Issue 2, September 1997

Documentation Development Lucent Technologies

Middletown, NJ 07748-9972 Printed in USA

TIME/DATE (display feature)

TIMER (display feature)

TRANSFER

Time/Date

Timer

Transfer

8434dx.qref.def2.fm Page 10 Friday, March 27, 1998 10:34 AM

All manuals and user guides at all-guides.com

Otros manuales para Definity 8434DX

Tabla de contenidos

Otros manuales de Terminal táctil de Lucent Technologies

Lucent Technologies

Lucent Technologies SLC-2000 Access System Central Office... Manual de usuario

Lucent Technologies

Lucent Technologies CIB 3000 Manual de usuario

Lucent Technologies

Lucent Technologies Voice Terminal 8434DX Manual de usuario

Lucent Technologies

Lucent Technologies 8528T Manual de usuario

Lucent Technologies

Lucent Technologies CIB 2853 Manual de usuario

Lucent Technologies

Lucent Technologies CIB 3023 Manual de usuario

Lucent Technologies

Lucent Technologies Merlin Magix Manual de usuario

Lucent Technologies

Lucent Technologies 8400 Series Manual de usuario

Lucent Technologies

Lucent Technologies 8400 Series Manual de usuario

Lucent Technologies

Lucent Technologies MLC-5 Manual de usuario

Lucent Technologies

Lucent Technologies Definity 8510T Manual de usuario

Lucent Technologies

Lucent Technologies SLC-2000 Access System Central Office... Manual de usuario

Lucent Technologies

Lucent Technologies SLC 5 Series Manual de usuario

Lucent Technologies

Lucent Technologies Mitel SX200D Series Manual de usuario

Lucent Technologies

Lucent Technologies CIB 7102 Manual de usuario

Manuales populares de Terminal táctil de otras marcas

Wincor Nixdorf

Wincor Nixdorf iPOS plus Advanced Manual de usuario

Ingenico

Ingenico AXIUM EX4000 Manual de usuario

Heisei Electronics

Heisei Electronics Q-POS 815 Manual de usuario

Amano

Amano MTX-15 Manual de usuario

FLOWBIRD

FLOWBIRD CWT Compact Touch Manual de usuario

Demco

Demco SP7 Manual de usuario

Lathem

Lathem PC600 Series Manual de usuario

Partner

Partner MF-2352 Manual de usuario

NCR

NCR RealPOS 7460-2 Manual

Simrad

Simrad MS50 Instrucciones de montaje

Unitech

Unitech MR350 MKII Guía de inicio rápido

Jungheinrich

Jungheinrich WMT 210 Manual de usuario

Motorola

Motorola MTP850 Manual de usuario

YASKAWA

YASKAWA 62H-MDC0 Manual de usuario

MVG industries

MVG industries NeptuLink Manual de usuario

Price Industries Limited

Price Industries Limited FDC Manual de instrucciones

Honeywell

Honeywell TemaKey Manual de usuario

EBN

EBN BPC65-B-A16G Manual de usuario