Lucent Technologies Cajun P333T Manual de usuario

Cajun™ P333T

Quick Start Guide

Unpack

Rack mount (optional)

Connect the cables

Configure

Run Web-based

Manager (optional)

Power up

Cajun P333T QS.qxd 18/07/2000 12:09 Page 1

Unpack

Check the package contents for the following:

EIf any items are missing or damaged, contact your supplier.

Equipment

• One Cajun P330 Layer 2 Workgroup Switch

• One AC power cable

• One RJ-45 to DB-9 serial adapter cable

• Four rubber feet

• Four screws with washers for rack mounting

EEthernet connection cables are not supplied

Documentation

• Cajun P333T Quick Start Guide (this document)

• Cajun P330 Release Notes

• Cajun P330 Documentation and Utilities CD (see detail below)

• Lucent Technologies Warranty and License Agreement

Cajun P330 Documentation and Utilities CD

The CD contains the latest User's Guides for the Cajun P330 stackable switches and files for

use with the Embedded Web Manager.

User's Guides

You can view and print these Guides using Adobe® Acrobat® Reader.

• Cajun P332MF

• Cajun P333T

• Cajun P334T

• Cajun P333R

• Cajun P330 Device Manager

Auxiliary Files for use with the Embedded Web Manager

Please refer to the documentation for information on how to use these files.

• Java plug-in

• Help files

Adobe Acrobat Reader

This application allows you to view and print the User's Guides on this CD.

Cajun P333T QS.qxd 18/07/2000 12:09 Page 2

Rack mount (optional)

1. Snap open the hinged ends of the unit’s front panel to reveal the screw holes.

2. Position the unit in the rack.

3. Secure the unit to the rack, taking care not to overtighten the screws.

4. Snap closed the hinged ends of the front panel.

EYou can now safely connect the cables to the unit.

WARNING: Disconnect all cables from the unit before proceeding with the rack

installation.

Cajun P333R

EXPANSION

SLOT

FDX

FIV

COLLNK

Tx Rx

LAG

HspdFC

SYSROUT

OPR PWR

11 12

13 14 15 16 17

LAG

234 5

CONSOLE

2118 19 20 2322 24

LAG

781110

LAG

Lucent

Cajun P333R

EXPANSION

SLOT

FDX

FIV

COLLNK

Tx Rx

LAG

HspdFC

SYSROUT

OPR PWR

11 12

13 14 15 16 17

LAG

234 5

CONSOLE

2118 19 20 2322 24

LAG

781110

LAG

Lucent

Closed hinged end

Open hinged end

Screw

holes

Cajun P333T QS.qxd 18/07/2000 12:09 Page 3

Power up

Cajun P330 AC Version

1. Insert the power cord into the power connector (BUPS or Power Supply) on the rear of

the unit.

2. Insert the other end of the power cord into the electricity supply or the BUPS connector.

KThe unit powers up and performs a self test procedure. The LEDs flash at regular

intervals after the self-test procedure is completed successfully.

Cajun P330 DC Version

WARNING: Before performing any of the following procedures, ensure that DC

power is OFF.

CAUTION: This product is intended for installation in restricted access areas and is

approved for use with 18 AWG copper conductors only. The installation must comply

with all applicable codes.

1. Connect the power cable to the switch at the input terminal block on the rear of the unit.

EThe terminals are marked “+”, “-“ and the IEC 5019a Ground symbol.

EThe size of the three screws in the terminal block is M3.5.

EThe pitch between each screw is 9.5mm.

2. Attach the appropriate lugs at the wire end of the power supply cord.

3. Wire the DC power supply to the terminal block.

KThe unit powers up and performs a self test procedure. The LEDs flash at regular

intervals after the self-test procedure is completed successfully.

WARNING: The proper wiring sequence is:

• ground to ground

• positive to positive (line to L)

• negative to negative (neutral to N)

Always connect the ground wire first and disconnect it last.

BUPS connector

AC connector

DC terminal

block

Cajun P333T QS.qxd 18/07/2000 12:09 Page 4

FIV – Force Initial Version (see Cajun P330

User’s Guide)

LNK – When ON, link is OK

COL – When ON, indicates a collision on

the port in HDX mode

Tx, Rx – Shows traffic activity for

transmitted and received packets

FDX – Shows Full/Half Duplex mode

FC – When ON, Flow Control is enabled for

a port in FDX mode

Hspd – Shows speed of port (10 Mbps or

100/1000 Mbps)

LAG – When ON, the port is included in a

Link Aggregation Group (LAG).

ROUT – Shows switch’s mode of operation

SYS – Shows whether this module is the

Cajun P330 Stack Master agent

OPR – Shows CPU boot status

PWR – Shows when power is on

Connect the cables

Connect PCs, servers, routers, workstations, and hubs

1. Connect the Ethernet connection cable (not supplied) to a 10/100 Mbps port on the front

panel of the Cajun P330.

EYou should use standard RJ-45 connections. You must use CAT-5 cable for 100 Mbps

operation.

2. Connect the other end of the cable to the Ethernet port of the PC, server, router, worksta-

tion, switch or hub.

EUse a cross cable when connecting the Cajun P330 to a switch or hub.

3. Check that the appropriate link (LNK) LEDs light up.

Connect the console cable

1. Configure the serial port settings of the PC or terminal as follows: Baud Rate – 9600,

Parity – no, Data bits – 8, Stop bits – 1, Flow control – no.

2. Connect the supplied special RJ-45 connector to the port marked “Console” on the front

panel of the Cajun P330.

3. Connect the other end of the cable to a terminal or PC with terminal emulation software

installed.

Cajun P333T LEDs

Left/Right &

Reset Switches Function LEDsFIV switch

Port LEDs

Cajun P333T QS.qxd 18/07/2000 12:09 Page 5

Basic configuration

To connect a PC terminal or VT-100 terminal to the Cajun P330

1. If you are using a PC, initiate a VT-100 terminal emulation session using an application

such as Windows® HyperTerminal.

2. Press Enter.

KThe Welcome to Cajun P330 menu is displayed.

3. Type the User name root when prompted and press Enter.

4. Type the User Level password root when prompted and press Enter.

KThe Cajun_P330-N(super)# prompt appears

ENis the number of the switch in the stack.

Assigning the Stack IP Address

ECommands are shown as follows: set interface inband;

parameters which you need to enter are shown in <> as follows: <vlan>

1. Type set interface inband <vlan> <ip_address> <netmask>, replacing

<vlan>, <ip_address> and <netmask> with the VLAN, IP address and net mask of

the stack and press Enter.

2. Press Enter to save the VLAN, IP address and net mask.

3. Type reset and press Enter to reset the stack at the Cajun_P330-N# prompt

4. After the Reset, perform login to Privileged level again as described in step 1.

KThe Cajun_P330-N(super)# prompt appears.

5. Type set ip route <dest> <gateway>, replacing <dest> and <gateway> with the

destination and gateway IP addresses and press Enter.

6. Press Enter to save the destination and gateway IP addresses.

Cajun P333T QS.qxd 18/07/2000 12:09 Page 6

Setting the Parameters

If you wish to change the default parameters shown and configure the mandatory

parameters, we recommend that you use the Command Line Interface (CLI).

EFor further information, please refer to Chapter 6 of the Cajun P330 User’s Guide.

Configuration Parameter Default Setting

Cajun P330 IP Address 149.49.32.134

BootP Mode Never

Default Gateway 0.0.0.0

Management PC SLIP IP Address 192.168.10.2

VLAN Management ID 1

Spanning Tree Enabled

TFTP Mode Limited

TFTP Server 0.0.0.0

TFTP File Name viisa

Configuration Parameter Default Setting

Port Speed and Duplex Mode • 10/100-TX ports: Auto-negotiation

• 100Base-FX ports: 100 Mbps full duplex

• 1000Base-X ports: 1000 Mbps full duplex

Flow Control • 10/100 and 100 Mbps: Disabled

• 1000 Mbps: Disabled (no pause)

Backpressure • 10/100: Enabled (when in half duplex mode)

• 100Base-FX & 1000 Mbps: Not applicable

Auto-negotiation • 10/100-TX ports: Enabled

• 100Base-FX ports: Not applicable

• 1000Base-X ports: Enabled

Administration State Enabled

Port VLAN ID 1

Tagging Mode Clear

Port Priority Regular

Default Switch Parameters

Default Port Parameters

Cajun P333T QS.qxd 18/07/2000 12:09 Page 7

Run the Web-Based Manager (optional)

ETo configure the Cajun P330 you can use the P330 Web-based Manager in addition to

using the CLI.

System Requirements

Minimum hardware and Operating System requirements are:

• Windows® 95 or NT® 4.0 or higher

• Pentium® 200 Mhz-based computer with 64 Mb of RAM (Pentium-II recommended)

• Minimum screen resolution of 1024 x 768 pixels

• Microsoft® Internet Explorer® 4 or

higher or

• Netscape Navigator® 4.xor higher

• Sun Microsystems Java™ plug-in version 1.2.2 (supplied)

Running the Embedded Manager

EAssign an IP address to the P330 before starting this procedure.

1. Open your browser.

2. Enter the URL of the switch in the form http: aaa.bbb.ccc.ddd

Eaaa.bbb.ccc.ddd is the IP address of the switch.

KYou are prompted to log into the switch.

EThe user name is “root”.

The default password for read-write access is “root”.

EThe Web management passwords are the same as those of the CLI. If you change the

passwords in the CLI then use those passwords for Web management as well.

KThe welcome page is displayed:

Cajun P333T QS.qxd 18/07/2000 12:09 Page 8

KIf you do not have the Java plug-in installed, the following message appears:

EIf the network manager has configured the system the plug-in should be installed auto-

matically.

If the plug-in is not installed automatically, there are three ways to install the plug-in

manually:

• Either install the plug-in from the CD as follows:

1. Close all unnecessary applications on your PC.

2. Insert the “Cajun P330 Documentation and Utilities” CD in the CD drive.

3. Click Start on the Task bar.

4. Select Run.

5. Type x:\emweb-aux-files\plugin_1_2_2.exe (where x: is the CD drive letter)

6. Follow the on-screen instructions.

• Or install the plug-in from the Lucent site by clicking on the link on the welcome page.

• Or, if the network manager has placed the files on the local site, install the plug-in from

there by clicking the link on the welcome page.

KIf you have the Java plug-in already installed or once you have successfully installed the

plug-in as described above, the Web-based manager opens in your browser.

Cajun P333T QS.qxd 18/07/2000 12:09 Page 9

Documentation and Online Help

Refer to the Cajun P330 Documentation and Utilities CD for full instructions

Cajun P333T QS.qxd 18/07/2000 12:09 Page 10

Otros manuales para Cajun P333T

Tabla de contenidos

Otros manuales de Cambiar de Lucent Technologies

Lucent Technologies

Lucent Technologies MAX TNT Manual

Lucent Technologies

Lucent Technologies Cajun P333T Manual de usuario

Lucent Technologies

Lucent Technologies Cajun P550 Guide Manual de usuario

Lucent Technologies

Lucent Technologies LambdaUnite Manual de usuario

Lucent Technologies

Lucent Technologies LambdaUnite MSS Manual de usuario

Lucent Technologies

Lucent Technologies CAJUN P880 Manual de usuario

Lucent Technologies

Lucent Technologies Cajun P220 Manual de instrucciones

Lucent Technologies

Lucent Technologies 5ESS Manual de usuario

Lucent Technologies

Lucent Technologies OptiStar EdgeSwitch Manual de usuario

Lucent Technologies

Lucent Technologies CAJUN M770 Manual de usuario

Lucent Technologies

Lucent Technologies LambdaUnite Manual de usuario

Lucent Technologies

Lucent Technologies Lucent Compact Switch Manual de usuario

Lucent Technologies

Lucent Technologies 4ESS Manual de usuario

Lucent Technologies

Lucent Technologies ED83134-30 Manual de usuario

Lucent Technologies

Lucent Technologies Cajun P220 Manual de usuario

Lucent Technologies

Lucent Technologies Cajun P115G Manual de usuario

Lucent Technologies

Lucent Technologies CAJUN M770 Manual de usuario

Lucent Technologies

Lucent Technologies 4ESS Manual de usuario

Lucent Technologies

Lucent Technologies CAJUN P120 Manual de usuario

Lucent Technologies

Lucent Technologies CBX 3500 Manual de usuario

Lucent Technologies

Lucent Technologies A500 Manual de usuario

Lucent Technologies

Lucent Technologies GX 550 ES Manual

Lucent Technologies

Lucent Technologies GX 550 Manual de usuario

Lucent Technologies

Lucent Technologies GRF 1600 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario