Ltech WP-804 Manual de usuario

WP-804

DMX/RDM CV Decoder

WP-804 DMX/RDM CV Decoder

WP-804

Output Power: (0-60...120)W/CH Max. 480W(4CH) Weight(N.W.): 690g

DMX512, RDMInput Signal: Working Temp.: -20°C~50°C

WP-804 uses the RDM protocol and supports DMX512/RDM signal bi-directional communication. The RDM pro-

tocol enables the remote management such as reading/ writing DMX address (the DMX master must be RDM

compliant). WP-804 has 4 channel output with max. 5A output for each channel. It can be used to control DIM,

CT, RGB, RGBW constant voltage lights and achieve 0-100% dimming or various lighting effects. WP-804 can be

operated in DMX mode or in customized mode.

Product Parameters

Dimming Range: 0-100% Short circuit, over temperature, over

current protection, auto recovery.

Protection:

Input Voltage: L164×W70×H36mm

Dimensions(L×W×H):

12-24V

Output Current: Package Size(L×W×H): L230×W95×H47mm

Max. 5A/CH Max. 20A(4CH)

It is easy to set address via digital display and buttons. WP-804 is a waterproof decoder with IP67 rating, sui-

table for outdoor and damp environments.

WP-804 DMX/RDM CV Decoder

Product Size

164mm

70mm

146mm

36mm

Main Component Description

Digital display

DMX/RDM signal input

LED lamp connection

DMX/RDM signal output

MODE SETUP

Digital display:

Access Configuration: Long press the MODE button for more than 2s.

Back to Start Page: Long press the MODE button for 2s again or after

15 seconds of inactivity.

Save Configuration: Long press the SETUP button for more than 2s.

Adjust Value: Short press or button.

Reset It to Factory Defaults: Long press MODE, , button simul-

taneously for 2s.

CV power input

WP-804 DMX/RDM CV Decoder

OLED display interface

DMX mode

Short press the MODE button and button simultaneously. When

the screen displays "L-1", it enters the DMX mode. Long press Mode

button for 2s to enter the menu. After parameter settings are com-

pleted, Long press the SETUP button for more than 2s to save the

configuration.

Interface of DMX mode

1. DMX address setting Press or button to set the DMX address.

DMX address range: 1~512

2. Resolution Short press MODE button to switch the menu to "r".

Press or button to select resolution and the third value on the

screen will display 1 or 2.

Options: / r-2 (16bit) r-1 (8bit)

3. PWM frequency Short press MODE button to switch the menu to "F".

Press or button to select PWM frequency and the third value on the

screen will display H or L.

Options: / FL- (300Hz) F-H (3600Hz)



4. Dimming mode Short press MODE button to switch the menu to "d".

Press or button to select the dimming mode and the third value on

the screen will display 1 or 2.

Options: / d-2 (Standard dimming) d-1 (Smooth dimming)

5. DMX channels

C-4 (4 channel output occupies corresponding 4 DMX addresses)

C-1 (4 channel output occupies DMX address 1)

C-2 (1st and 3rd channel output occupy DMX address 1; 2nd and

4th channel output occupy DMX address 2 )

C-3 (1st channel output occupies DMX address 1; 2nd channel

output occupies DMX address 2; 3rd and 4th channel output

occupy DMX address 3)

Short press MODE button to switch the menu to "C".

Press or button to select the channels and the third value on the

screen will display 1, 2, 3 or 4.

Options:

6. Screen timeout Short press MODE button to switch the menu to "n".

Press or button to select screen timeout and the third value on the

screen will display 1 or 2.

Options: n-1 (Screen stays on)

n-2 (Screen turns off after 30 seconds of inactivity)

WP-804 DMX/RDM CV Decoder

Customized mode

Interface of customized mode

Short press the MODE and button simultaneously. When the

screen displays "L-2", it enters the customized mode. Long press

the MODE button for 2s to enter the menu. After parameter sett-

ings are completed, Long press the SETUP button for more than

2s to save the configuration.

1. Lighting effects

e.g. E-A (7-color gradient)

Short press MODE button to switch the menu to "E".

Pressor button to select the lighting effect and the third value

on the screen will display 1, 2, 3, 4, 5, 6, 7, 8, 9 or A.

Options:

E-1 (no lighting effect)

E-2 (Red)

E-3 (Green)

E-4 (Blue)

E-5 (Yellow)

E-6 (Purple)

E-7 (Cyan)

E-8 (White)

E-9 (7-color jumping)

E-A (7-color gradient)

e.g. E-1 (no lighting effect)

2. Color-changing speed Short press MODE button to switch the menu to "S".

Press or button to select speed and the third value on the

screen will display 1, 2, 3, 4, 5, 6, 7 or 8.

Default: S-5

Options: S-1 / S-2······S-7 / S-8 

Speed levels, speed increases one by one

3. Brightness Short press MODE button to switch the menu to "B".

Press or button to select the brightness level and the third

value on the screen will display 1, 2, 3, 4, 5, 6, 7 or 8.

Default: B-8

Options: B-1 / B-2 ······ B-7 / B-8 

Brightness levels, brightness increases one by one

4. Screen timeout Short press MODE button to switch the menu to "n".

Press or button to select screen timeout and the third value on the

screen will display 1 or 2.

Options: n-1 (Screen stays on)

n-2 (Screen turns off after 30 seconds of inactivity)

GND

D+

D-

PUSH

LED+

WP-8 04

LED+

WP-8 04

LED+

WP-8 04

WP-804 DMX/RDM CV Decoder

Wiring Diagram

DMX console

DMX/RDM

input

DMX/RDM

input

DMX/RDM

output

DMX/RDM

output

DMX/RDM

input

If the recoil effect occurs because of long signal line or poor quality wires, please try to connect a 0.25W 90-120Ω terminal resistor at

the end of each line.

When more than 32 DMX decoders are connected, DMX signal amplifiers are needed and signal amplification should not be more than

5 times continuously. If you need to modify the parameter settings of connected DMX/RDM decoders that exceed 32, you can add 1 RDM

signal amplifier. Or you can add 1-5 DMX signal amplifiers after completing the parameter settings.

CV power

12-24V

CV power

12-24V

CV power

12-24V

WP-804 DMX/RDM CV Decoder

Attentions

This product must be installed and adjusted by a qualified professional.

This product is non-waterproof (special models excepted). Please avoid the sun and rain. When installed outdoors,

please ensure it is mounted in a water proof enclosure.

Good heat dissipation will extend the life the product. Please install the product in a environment with good ventilation.

When you install this product, please avoid being near a large area of metal objects or stacking them to prevent signal

interference.

Please keep the product away from aintensemagneticfield, a high pressure area or a place where lightning is easy

to occur.

Please check whether the working voltage used complies with the parameter requirements of the product.

Before you power on the product, please make sure all the wiring is correct in case of incorrect connection that may

cause a short circuit and damage the components, or trigger a accident.

If a fault occurs, please do not attempt to fix the product by yourself. If you have any question, contact the supplier.

Update Time: 27/02/2023_A0

www.ltech-led.com

This manual is subject to changes without further notice. Product functions depend on the goods. Please feel free

to contact our official distributors if you have any question.

Warranty Agreement

Warranty exclusions below:

Beyond warranty periods.

Any artificial damage caused by high voltage, overload, or improper operations.

Products with severe physical damage.

Damage caused by natural disasters and force majeure.

Warranty labels and barcodes have been damaged.

No any contract signed by LTECH.

Warranty periods from the date of delivery: 5 years.

Free repair or replacement services for quality problems are provided within warranty periods.

1. Repair or replacement provided is the only remedy for customers. LTECH is not liable for any incidental or conse-

quential damage unless it is within the law.

2. LTECH has the right to amend or adjust the terms of this warranty, and release in written form shall prevail.

Tabla de contenidos

Otros manuales de Convertidor de medios de Ltech

Ltech

Ltech LT-DMX-1809 Manual de usuario

Ltech

Ltech Artnet-DMX-8 Manual del operador

Ltech

Ltech Artnet-SPI-8 Manual de usuario

Ltech

Ltech SE 20 250-1000-W2B2 Manual de usuario

Ltech

Ltech Artnet-DMX-1 Manual de usuario

Ltech

Ltech LT-858-CC Manual de usuario

Ltech

Ltech LT-904 Manual de usuario

Ltech

Ltech LT-916 Manual de usuario

Ltech

Ltech LT-830-700 Manual de usuario

Ltech

Ltech LT-912-OLED Manual de usuario

Ltech

Ltech LT-890 Manual de usuario

Ltech

Ltech LT-874S-5A Manual del operador

Ltech

Ltech LT-858-5A Manual de usuario

Ltech

Ltech LT-DMX-3001 Manual de usuario

Ltech

Ltech LT- 830 Manual de usuario

Ltech

Ltech LT-932-OLED Manual de usuario

Ltech

Ltech LT-874-5A Manual de usuario

Ltech

Ltech LT-830-8A Manual de usuario

Ltech

Ltech LT-854-5A Manual de usuario

Ltech

Ltech LT-DMX-6803 Manual de usuario

Ltech

Ltech LT-853-6A Manual de usuario

Ltech

Ltech LT-DMX-8020 Manual de usuario

Ltech

Ltech LT-912 Manual de usuario

Ltech

Ltech LT-8048 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario