LSIS XGT Series Manual de usuario

User’s Manual

Programmable Logic Controller

Cnet I/F Module

XGL-C22

XGL-C22B

XGL-CH2

XGL-CH2B

XGL-C42

XGL-C42B

XGT Series

Safety Instructions

Before using the product …

For your safety and effective operation, please read the safety instructions

thoroughly before using the product.

► Safety Instructions should always be observed in order to prevent accident

or risk with the safe and proper use the product.

► Instructions are divided into “Warning” and “Caution”, and the meaning of the

terms is as follows.

WARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury. It may also be used to alert against unsafe

practices

► The marks displayed on the product and in the user’s manual have the

following meanings.

Be careful! Danger may be expected.

Be careful! Electric shock may occur.

► The user’s manual even after read shall be kept available and accessible to

any user of the product.

Warning

Caution

Safety Instructions

Safety Instructions for design process

 Please install a protection circuit on the exterior of PLC so that the

whole system may operate safely regardless of failures from

external power or PLC. Any abnormal output or operation from PLC

may cause serious problems to safety in whole system.

- Install protection units on the exterior of PLC like an interlock circuit

that deals with opposite operations such as emergency stop,

protection circuit, and forward/reverse rotation or install an interlock

circuit that deals with high/low limit under its position controls.

- If any system error (watch-dog timer error, module installation error,

etc.) is detected during CPU operation in PLC, all output signals are

designed to be turned off and stopped for safety. However, there are

cases when output signals remain active due to device failures in

Relay and TR which can’t be detected. Thus, you are recommended

to install an addition circuit to monitor the output status for those

critical outputs which may cause significant problems.

 Never overload more than rated current of output module nor

allow to have a short circuit. Over current for a long period time may

cause a fire .

 Never let the external power of the output circuit to be on earlier

than PLC power, which may cause accidents from abnormal output or

operation.

 Please install interlock circuits in the sequence program for safe

operations in the system when exchange data with PLC or modify

operation modes using a computer or other external equipments

Read specific instructions thoroughly when conducting control

operations with PLC.

Warning

Safety Instructions

Safety Instructions for design process

Safety Instructions on installation process

 I/O signal or communication line shall be wired at least 100mm

away from a high-voltage cable or power line. Fail to follow this

instruction may cause malfunctions from noise

Caution

 Use PLC only in the environment specified in PLC manual or

general standard of data sheet. If not, electric shock, fire, abnormal

operation of the product may be caused.

 Before install or remove the module, be sure PLC power is off. If

not, electric shock or damage on the product may be caused.

 Be sure that every module is securely attached after adding a

module or an extension connector. If the product is installed loosely

or incorrectly, abnormal operation, error or dropping may be caused.

In addition, contact failures under poor cable installation will be causing

malfunctions as well.

 Be sure that screws get tighten securely under vibrating

environments. Fail to do so will put the product under direct vibrations

which will cause electric shock, fire and abnormal operation.

 Do not come in contact with conducting parts in each module,

which may cause electric shock, malfunctions or abnormal operation.

Caution

Safety Instructions

Safety Instructions for wiring process

 Prior to wiring works, make sure that every power is turned off. If

not, electric shock or damage on the product may be caused.

 After wiring process is done, make sure that terminal covers are

installed properly before its use. Fail to install the cover may cause

electric shocks.

Warning

 Check rated voltages and terminal arrangements in each product

prior to its wiring process. Applying incorrect voltages other than

rated voltages and misarrangement among terminals may cause fire or

malfunctions.

 Secure terminal screws tightly applying with specified torque. If the

screws get loose, short circuit, fire or abnormal operation may be caused.

Securing screws too tightly will cause damages to the module or

malfunctions, short circuit, and dropping.

 Be sure to earth to the ground using Class 3 wires for FG terminals

which is exclusively used for PLC. If the terminals not grounded

correctly, abnormal operation or electric shock may be caused.

 Don’t let any foreign materials such as wiring waste inside the

module while wiring, which may cause fire, damage on the product or

abnormal operation

 Make sure that pressed terminals get tighten following the

specified torque. External connector type shall be pressed or

soldered using proper equipments.

Caution

Safety Instructions

Safety Instructions for test-operation and

maintenance

Safety Instructions for waste disposal

 Do not make modifications or disassemble each module. Fire,

electric shock or abnormal operation may occur.

 Prior to installing or disassembling the module, let all the external

power off including PLC power. If not, electric shock or abnormal

operation may occur.

 Keep any wireless equipment such as walkie-talkie or cell phones

at least 30cm away from PLC. If not, abnormal operation may be

caused.

 When making a modification on programs or using run to modify

functions under PLC operations, read and comprehend all

contents in the manual fully. Mismanagement will cause damages to

products and accidents.

 Avoid any physical impact to the battery and prevent it from

dropping as well. Damages to battery may cause leakage from its fluid.

When battery was dropped or exposed under strong impact, never

reuse the battery again. Moreover skilled workers are needed when

exchanging batteries.

Caution



Product or battery waste shall be processed as industrial waste.

The waste may discharge toxic materials or explode itself.

Caution

 Don’t touch the terminal when powered. Electric shock or abnormal

operation may occur.

 Prior to cleaning or tightening the terminal screws, let all the

external power off including PLC power. If not, electric shock or

abnormal operation may occur.

 Don’t let the battery recharged, disassembled, heated, short or

soldered. Heat, explosion or ignition may cause injuries or fire

Warning

Revision History

Version Data Remark Page

V 1.0 2005.03 First Edition -

V1.1 2005.05 Add function description -

V1.2 2005.09 Change available CPU device address -

V2.0 2007.01 Change XG-PD description -

V 2.1 2008.02

1. Adding contents

(1) Production Configuration

(2) Software to use the product

(3) Operation Sequence

(4) I/O assignment and Device Information

(5) General of Communication Parameter

(6) Transmission Standard

(7) How to set transmission Standard

(8) Menu bar and shortcut of XG-PD

(9) Operation Start

(10) Diagnosis Function of XG-PD

<Ch.7 XGT Dedicated Communication>

(11) Summary of Protocol

(12) Frame Structure

(13) XGT Communication Function

(14) Remote Connection

(15) Modem Communication

(16) Communication Command

<Ch.8 Modbus Communication>

(17) General

(18) Modbus Protocol

(19) Structure of Frame

(20) Modbus Server

(21) Modbus RTU/ASCII Client

(22) Frame Monitor

<Ch.9 User-defined Communication>

(23) General

(24) Structure of user definition frame

(25) Frame Monitor

(26) Trouble shooting

1-3

1-4 ~ 1-5

4-3

4-6 ~ 4-13

6-1

6-2

6-25

6-27 ~ 6-28

6-35 ~ 6-37

6-42 ~ 6-48

7-1 ~ 7-47

8-1 ~ 8-31

9-1 ~ 9-11

11-9 ~ 11-11

Revision History

Version Data Remark Page

(27) User interface using Visual Basic

(28) Dimension

(29) Index

2. Fixing the contents

(1) Introduction

(2) Characteristics

(3) Performance Specifications

(4) Designation of Parts

(5) Cable Specifications

(6) Terminal Resistance

(7) Channel Operation during Normal Run

(8) Method of Serial Interface

(9) P2P setting parameter

(10) Available System Configurations

(11) Unavailable System Configurations

(12) Communication Module Registration

(13) Safety Instructions

A-18 ~ A-29

A-30

A-31 ~ A-32

1-1

1-2

2-2

2-3

2-4

2-5

3-2

3-4

4-5

5-1~ 5-6

5-7 ~ 5-8

6-20 ~ 6-24

V2.2 2008.07

1. Head office address change

2. Adding contents

(1) How to configure XGR basic system

(2) Available device area per CPU

3. Fixing the contents

(1) Introduction

(2) Product Specification

(3) Installation and Test Operation

(4) Communication Parameter

(5) XGT dedicated communication

(6) Modbus communication

(7) User defined communication

(8) Example program

(9) Diagnosis

(10) Standard setting window modification

Back cover

4-8

4-12

1-1,1-3

2-3

4-4, 4-9

6-1, 6-47

7-3, 7-5

8-18, 8-24

9-3

10-7

11-4

Entire

V2.3 2010.03

1. Characteristics modified

2. CPU added

3. Content on the remote connection modified

Ch1.2

Ch1.3.2

Ch7.4.2

V2.4 2010.06

1. Change general specification

2. Change Null modem connection cable

3. Back cover address update

2-1

3-4

Back cover

V2.5 2011.05 1. How to enable link through flag added CH6.7.2

Revision History

Version Data Remark Page

V2.6 2014.01

1. Delete XGR main base module description

2. Add RS-485 communication cable direction

3. Not usable system configuration

4. Add parity bit Ignore function

5. Add UDATA instruction

6. Add example UDATA function

CH1.3.2, CH2.2,

CH4.5.1

CH3.4.2

CH5.2.1

CH6.1.1, CH6.2.1

CH9.5

CH10.6

V2.8 2014.11 XG5000 V4.0 UI Updated Entire

V3.0 2016.02

1. Add Cnet V5.0 related feature

2. Add Ch.8 LS bus protocol (for Cnet V5.0)

3. Add appearance drawing of XGL-Cx2B

4. Add repeater mode

Ch1,2,3,4,6,9,10,11,12

Ch8

Appendix

CH3

V3.1 2019.06 1. Edit phrase Entire

※The number of User’s manual is indicated right part of the back cover.

About User’s Manual

Congratulations on purchasing PLC of LSIS Co.,Ltd.

Before use, make sure to carefully read and understand the User’s Manual about the functions, performances, installation

and programming of the product you purchased in order for correct use and importantly, let the end user and maintenance

administrator to be provided with the User’s Manual.

The User’s Manual describes the product. If necessary, you may refer to the following description and order accordingly. In

addition, you may connect our website (http://www.lsis.com/) and download the information as a PDF file.

Relevant User’s Manuals

Title Description

XG5000 User’s Manual XG5000 software user manual describing online function such as programming,

print, monitoring, debugging by using XGK, XGB CPU

XG5000 User’s Manual

(for XGI, XGR) XG5000 software user manual describing online function such as programming,

print, monitoring, debugging by using XGI, XGR CPU

XGK/XGB Instructions &

Programming User’s

Manual

User’s manual for programming to explain how to use instructions that are used

PLC system with XGK, XGB CPU.

XGI/XGR Instructions &

Programming User’s

Manual

User’s manual for programming to explain how to use instructions that are used

PLC system with XGI, XGR CPU.

XGK CPU User’s Manual

(XGK-CPUU/CPUH/

CPUA/CPUS/CPUE)

XGK-CPUU/CPUH/CPUA/CPUS/CPUE user manual describing about XGK

CPU module, power module, base, IO module, specification of extension cable

and system configuration, EMC standard

XGI CPU User’s Manual

(XGI-CPUU/D,CPUU,

CPUH,CPUS,CPUE)

XGI-CPUU/D,CPUU,CPUH,CPUS,CPUE user manual describing about XGI

CPU module, power module, base, IO module, specification of extension cable

and system configuration, EMC standard

XGR redundant series

User’s Manual

XGR- CPUH/F, CPUH/Tuser manual describing about XGR CPU module,

power module, extension drive, base, IO module, specification of extension cable

and system configuration, EMC standard

Current user manual of XGL-C22A, C22B, CH2A, CH2B, C42A, C42B is written based on the following version.

Related OS version list

Product name OS version

XGK-CPUU, CPUH, CPUA, CPUS, CPUE V4.5

XGI-CPUU/D, CPUU, CPUH, CPUS, CPUE V3.9

XGR-CPUH/F, CPUH/T, CPUH/S V2.6

XG5000 V4.07

Otros manuales para XGT Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Controladores de LSIS

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS LSLV-S100 Series Manual de usuario

LSIS

LSIS S100 Series Manual de programación

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS XEC-DN32H/DC Manual de usuario

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS sv-ip5a Manual de usuario

LSIS

LSIS XDL-L7SA002X Manual de usuario

LSIS

LSIS XEC-DR32H Manual de usuario

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS XBC-DR20SU Manual de usuario

LSIS

LSIS XP10BKA/DC Manual de usuario

LSIS

LSIS SV-iS7 series Manual de usuario

LSIS

LSIS XBF-AD04A Manual de usuario

LSIS

LSIS MASTER-K200S Manual del propietario

LSIS

LSIS XBM-DN16S Manual de usuario

LSIS

LSIS XDL-L7NH Series Manual de usuario

LSIS

LSIS XGT Series Manual de usuario

LSIS

LSIS Master-K K200S Manual de usuario

LSIS

LSIS XGL-EFMT Manual de usuario

LSIS

LSIS XBC-DN32U Manual de usuario

LSIS

LSIS XGL-CH2A Manual de usuario

Manuales populares de Controladores de otras marcas

Digiplex

Digiplex DGP-848 Instrucciones de funcionamiento

YASKAWA

YASKAWA SGM series Manual de usuario

Sinope

Sinope Calypso RM3500ZB Manual de usuario

Isimet

Isimet DLA Series Style 2 Manual de instalación

Rockwell Automation

Rockwell Automation 1769-L31 Manual de usuario

Airflow

Airflow Uno hab Manual de usuario

ABB

ABB ACS580-01 drives Manual de usuario

Panasonic

Panasonic GM1 Series Manual de usuario

Emerson

Emerson SW93 Manual de usuario

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manual de usuario

Panasonic

Panasonic FP? Positioning Unit RTEX Manual de usuario

Samson

Samson Type 5824 Manual de servicio

Alpha IP

Alpha IP MIOB 21001 Manual de usuario

Siemens

Siemens OpenAir GMA 1 Series Manual de usuario

Surecom

Surecom SR-629 Manual de usuario

Fishman

Fishman TriplePlay Manual de usuario

Regulus

Regulus SRS1 T Manual de usuario

3M MicroTouch EX113 Manual de usuario