LSG RB-2 Manual de usuario
NOTE: This manual may be subject to updates or changes. Up to date manuals are available through our website at www.lifespanfitness.com.au
RB-2 OWNER’S MANUAL
Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for future
reference.
2
RB-2
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. CARE INSTRUCTIONS 4
3. ASSEMBLY INSTRUCTIONS 5
4. COMPUTER OPERATION 11
5. EXERCISE GUIDE 13
6. EXPLODED DIAGRAM 15
7. PARTS LIST 16
8. WARRANTY 17
3
RB-2
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this machine.
It is important your machine receives regular maintenance to prolong its useful life. Failing to regularly
maintain your machine may void your warranty.
Please keep this manual with you at all times
a. It is important to read this entire manual before assembling and using the equipment. Safe and effective
use can only be achieved if the equipment is assembled, maintained and used properly.
Please note: It is your responsibility to ensure that all users of the equipment are informed of all warnings
and precautions.
b. Before starting any exercise program you should consult your doctor to determine if you have any medical
or physical conditions that could put your health and safety at risk, or prevent you from using the
equipment properly. Your doctor’s advice is essential if you are taking medication that affects your heart
rate, blood pressure or cholesterol level.
c. Be aware of your body’s signals. Incorrect or excessive exercise can damage your health. Stop exercising
if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, and
extreme shortness of breath, lightheadedness, dizziness or feelings of nausea. If you do experience any of
these symptoms, you should consult your doctor before continuing with your exercise program.
d. Keep children and pets away from the equipment. This equipment is designed for adult use only.
e. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet. To ensure
safety, the equipment should have at least 2 meters of free space around it.
f. Before using the equipment, check that the nuts and bolts are securely tightened. If you hear any unusual
noises coming from the equipment during use and assembly, stop immediately. Do not use the equipment
until the problem has been rectified.
4
RB-2
g. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may get caught in the
equipment or that may restrict or prevent movement.
h. This equipment is designed for indoor and family use only
i. Care must be taken when lifting or moving the equipment so as not to injure your back.
j. Always keep this instruction manual and assembly tools at hand for reference.
k. The equipment is not suitable for therapeutic use.
l. The pulse or heart rate sensors are not medical devices. Various factors, including the user’s movement,
may affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
2. CARE INSTRUCTIONS
a. Lubricate moving joints with grease after periods of usage
b. Be careful not to damage plastic or metal parts of the machine with heavy or sharp objects
c. The machine can be kept clean by wiping it down using dry cloth
d. All nuts and bolts are to be checked and tightened on a regular basis. This includes pedals and other
moving parts. Failure to do so may cause damage to your thread and void your warranty.
Battery Usage
a. Batteries are to be installed or replaced by adults only
b. Do not use rechargeable batteries. Do not mix different battery types. Do not mix old and new batteries.
Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries
c. Remove batteries when product is not in use
5
RB-2
d. Remove exhausted batteries from product and dispose of in accordance with the manufacturer’s
recommendation
e. Do not attempt to recharge non-rechargeable batteries
f. Batteries are to be inserted with correct polarity
g. The supply terminals are not to be short-circuited
h. Do not dispose of batteries in fire, batteries may explode or leak
3. ASSEMBLY INSTRUCTIONS
Tools
Most of the listed assembly hardware has been packaged separately, but some hardware items have been
preinstalled in the identified assembly parts. In these instances, simply remove and reinstall the hardware as
assembly is required.
Please reference the individual assembly steps and make note of all preinstalled hardware
Preparation
Prior to assembly, make sure that you will have enough space around the item; Use the present tooling for
assembly; before assembling please check whether all needed parts are available.
It is strongly recommended this machine to be assembled by two or more people to avoid possible injury.
6
RB-2
STEP 1:
1. Disassemble the hex nut (20) and flat washer (21) from the front main frame (1) with the wrench. Then
lock the hex nut (20) and flat washer (21) into the hole of the rear main frame (9).
7
RB-2
STEP 2:
1. Cover two the rear end cap (8) to the ends of the rear stabilizer (3) respectively.
2. Lock the rear stabilizer (3) to the rear main frame (9) with carriage bolt (4), arc washer (5) and acorn nut
(6).
3. Lock the front stabilizer (2) to the front main frame (1) with carriage bolt (45), arc washer (13) and acorn
nut (6).
4. Connect the extension pulse wire 1 (10) with the extension pulse wire 2 (26) together, then fix the front
main frame (1) to the rear main frame (9) with hex nut (20), spring washer (42) and flat washer (21).
STEP 3:
1. Secure the seat frame (23) on the rear main frame (9) with flat washer (17) and plum knob (16),
adjusting to a suitable distance, then fasten tightly.
8
RB-2
STEP 4:
1. Lock the saddle (24) on the seat frame (23) with screw (20) and flat washer (21).
2. Lock the backrest (25) on the seat frame (23) with screw (50) and flat washer (49).
3. Fit the back bracket cover to the seat frame (23) with screw (51).
STEP 5:
1. Connect the pulse wire (14) and the extension pulse wire 1 (10) together. Then fasten the handlebar
(15L/R) to the rear main frame (9) tightly with Allen bolt (12), flat washer (21) and acorn nut (6).
9
RB-2
STEP 6:
1. Lock the pedal (27L/R) to the crank (46L/R).
NOTE: To tighten, turn the left pedal COUNTER-CLOCKWISE and the right pedal CLOCKWISE. And please
make sure the pedal (27L/R) are locked tightly during your training, otherwise the pedal will be broken.
IMPORTANT: FAILURE TO FOLLOW PROCEDURES MAY RESULT IN PERMANENT DAMAGE TO YOUR
BIKE.
STEP 7:
1. Connect the extension pulse wire 2 (26) with extension pulse wire 3 (30), and connect the extension
wire (31) with sensor wire (28).
2. B: Feed the tension connecting wire (29) through the bottom of the handlebar post (32) and pull it out
from the hole on the handlebar post (32).
3. Then connect the cable of the tension controller (33) with the hook of the tension connecting wire (29)
10
RB-2
as shown in picture A.
4. C: Lock the tension controller (33) to the handlebar post (32) with screw (35) and arc washer (34).
5. D: Insert the handlebar post (32) to the post of front main frame (1), secure in place with screw (20)
and arc washer (13) which are pre-attached to the Main Section.
STEP 8:
1. Lock the fixed handlebar (39) on the handlebar post (32) with the plastic handlebar screw (37),
handlebar cover (36), flat washer (21) and spacer (38).
STEP 9:
1. Connect the extension pulse wire 3 (30) and sensor wire (31) with the relevant cables of the computer
(44),then lock the computer (44) on the bracket of the handlebar post (32) with screws (41).
Tabla de contenidos
Otros manuales de Bicicleta estática de LSG
LSG
LSG SPG-220 Manual de usuario
LSG
LSG SPG-200 Manual de usuario
LSG
LSG SPG-120 Manual de usuario
LSG
LSG ERG-400 Manual de usuario
LSG
LSG RB-100 Manual de usuario
LSG
LSG RB-1 Manual de usuario
LSG
LSG EXER-10 Manual de usuario
LSG
LSG RB-1 Manual de usuario
LSG
LSG SPG-230 Manual de usuario
LSG
LSG SPG-100 Manual de usuario
