LRS Table Genie Hoja de especificaciones

To A emble the Table Genie

1. Remove Table Genie from packaging.

2. Contents will include:

• 1 Table Genie

• 1 Table Plate

• 1 Double side foam tape

• 1 AA Battery

3. Pull the release tab back, then lift and remove

the battery cover.

4. Insert the AA battery.

5. Reassemble the Table Genie

To Mount the Table Genie To the Table:

1. Choose to either use Double sided Foam Tape or

3 screws to hold the Table Plate to the Table.

2. Secure Table Plate to the Table.

3. Slide the Table Genie onto the Table Plate.

Pu h For Service Monitor

1. Press ENTER.

2. Press EXIT.

Long Range Systems 1Table Genie Quick Guide

Table Genie

System Interface Transmitter

QUICK SETUP & OPERATION

Relea e Tab of Battery Cover

Pull in Direction of Arrow

Battery

Push For Service

www.pager.net

A ociating Table Genie

1. From the Setup menu select SYSTEM TOOLS.

2. Select WPAN.

3. Select Associate (the unit will stay in associate for 5 minutes and then associate

will have to be restarted.)

4. Install a battery in the Table Genie and press all 3 buttons after the unit begins to

flash. Then:

• The buttons will light back and forth.

• The buttons will flicker rapidly.

• The buttons will go out.

• The popup will ask for the entry of a table number.

5. Repeat steps 3 and 4 until all units are associated.

6. To exit, press EXIT on T7502.

Note: If unit fails to join, remove battery, put unit aside, and repeat process after all

other units are joined.

Operation

1. When a button is pressed on the Table Genie, a table number will be displayed

and timer will start on the monitor.

2. The last pressed button on the Table Genie will blink until cleared.

3. To clear a unit, use the user defined cancel sequence (see user manual to change.)

4. When cleared, the button will stop flashing and the monitor will clear.

5. If the table monitor is not cleared

• Within a preset time, the color for that table will change to yellow.

• If the table is still not cleared after another preset time, the monitor for that table

will turn red and the manager will be paged.

• The manager will periodically be re paged until the table is cleared.

Setup for Table Genie Operation

From the Setup menu select GLOBAL SETTINGS.

1. Select OPERATION MODE then Push For Service Monitor

2. Press ENTER.

3. Press EXIT.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause harmful interference.

Warning: Changes or modifications not expressly approved by Long Range Systems could void the user's

authority to operate the equipment.

Long Range Systems 2Table Genie Quick Guide

XU-0058 091114

Tabla de contenidos

Otros manuales de Transmisor de LRS

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario