Look Solutions UNIQUE 2 Manual de usuario

Operating manual

aLook Solutions product

Set of Equipment supplied

– 1 Unique2

– 1 tank lid with quick connector, silicon tube and air valve filter

– 1 canister of UNIQUE-fluid, 2l

– 1 manual

As an option:

– XLR remote for analog control (delivered without cable)

– Diverter

– Case

– Hanging set

– Radio remote (for starting the HDCS profile only)

Please check whether all the products you ordered are supplied.

Contents

1. Introduction 4

2. Safety instructions 5

3. Description of the parts 6

4. Fluid 7

4.1 General notes

4.2 Changing the fluid canister

4.3 Storage of the fluid

4.4 Fluid consumption

5. Operating the Unique29

5.1 Selecting the location

5.2 Putting into operation

5.3 Switching the device off

5.4 Control choices

5.4.1 Control via DMX 512

5.4.1.1 Adjusting the DMX start address

5.4.1.2 Adjusting the pump and the fan

5.4.2 Control via 0 - 10 Volt (+) DC

5.4.2.1 Adjusting the pump and the fan

5.4.3 Stand alone mode

5.4.3.1 Adjusting the pump and the fan

5.4.4 Control via Haze-Density Control System (HDCS)

5.4.4.1 Using the Profile

5.4.5 Working with the internal Timer

5.4.5.1 Autostart

5.5 Wiring of the sockets

6. Cleaning, Care and Maintenance 17

7. Troubleshooting 17

8. Specifications 18

9. Warranty conditions 19

1. Introduction

The haze machine Unique2offers various new features, which open new fields

of operation to the user.

With its variable output, the machine can be used in many fields of operation.

Any desired effect can be achieved: from the finest mist to a thick haze, similar to

fog. Therefore the Unique2is able to fill rooms or halls with a constant haze,

creating the right atmosphere and is greatly enhancing lighting effects.

The pump and the fan are fully and separately controllable, giving the Unique2

a good level of noise reduction. The machine can therefore be used in fields of

operation where any sound is undesirable or causes disturbance.

The ready-mixed fluid, available in canisters of 2 litres, guarantees a trouble-

free operating and continuous output for up to 50 hours.

The warm up time is extremely short (max. 1 min.)

With its power requirement of 1300 watt the Unique2is very powerful.

2. Safety instructions

A fog machine is not a toy!

• Very hot steam escapes from the nozzle. Danger of getting burnt.

• Occasionally very hot droplets of fluid may escape when in operation.

Thus never aim at persons directly and keep a minimum distance of 10 ft to the

nozzle.

• Never touch the nozzle when in operation. Danger of getting burnt.

• The location for the machine must be non-flammable, non-combustible and

not sensitive to heat. It has to be twice as big as the machine.

• Keep a minimum distance of 2 ft to all flammable, combustible objects and

objects sensitive to heat.

• Never open the machine and leave the machine unattended when connected

to a power supply.

• The visibility has to be more than 6 ft in rooms where people walk around.

• Only use the supplied „UNIQUE-fluid“. Different types of fluid do not gene-

rate the fog you require and destroy your fog generator.

• Do not swallow the fog fluid. Keep it away from children. In case of eye contact,

rinse with a lot of water. Consult a doctor should you have accidentally

swallowed some fluid.

• Spilled fluid or splashed fluid droplets can cause slip hazard. Mop up the fluid

and dispose of it according to regulations. UNIQUE-fluid is completely water-

soluble and biodegradable.

• Fog may activate smoke detectors.

Artificially-made fog can be produced in many different ways. The method

used here to produce fog, with a device which works according to the vaporizer

principle, is the most harmless one.

No case has so far been reported in which a sound human being has been

harmed because of using our device to produce artificial fog. However, this can

only be guaranteed if the professional fog generators are used accordingly, i.e.

at the correct vaporization temperatures as well as with the correctly mixed fog

fluid.

We, however, recommend: People with health problems or problems of the

respiratory tract or with an inclination for allergies should avoid any contact

with artificially-made fog.

230 V~/50Hz/1500W

Made by OTTEC Technology GmbH for

Look

- Solutions made in Germany

analog in dmx

512

Serial no.

This machine has been designed to be used with original Look Unique-fluid.

Use of other liqui ds will void the manufact urer's warr ant y and can be

dangerous to your health. Never use cleaner or fragrances with this

machine!

P 2 5

Rear view

Front view

7: · Nozzle

Vap our a nd no zzl e are a

extremely hot. Do not touch!

Do not cover the nozzle area

and do not connect a ducting!

3. Description of the parts

1: · Power cable

2: · XLR sockets for DMX in/out

3: · XLR socket for 0-10 V (+) DC

4: · Fluid tube inlet

5: · Fluid tube

6: · Control panel for adjusting

the DMX start address and

the output

3. Description of the parts

Tank lid

4. Fluid

9: · Brass collar

10: · Tank lid

11: · Brass coupling

12: · Fluid filter

13: · Check valve

The ready-to-use UNIQUE-Fluid for use in the Unique2is available in 2 litre

canisters from your local dealer. Fluid also comes in 10 and 25 litre canisters and

barrels with 220 litres.

To guarantee trouble-free operation the special “UNIQUE-Fluid“ must be used.

Use of other liquids will void the manufacturer‘s warranty and can be dangerous

to your health.

PLEASE NOTE: The vaporizer of our machines does not have to be cleaned!

Cleaners, available on the market, can damage the vaporizer! We cannot grant

warranty in this case.

4.1 General notes

4.3 Storage of the fluid

The “UNIQUE-Fluid“ is a highly concentrated fluid (but do not dilute it). You

can store it for a very long period.

4. Fluid

0 10 20 30 40 50 60 70 80 90 100

Fluid consumption

Unique vs. Unique2

Unique

Unique2

Fluid consumption (ml/min)

Pump value (%)

4.2 Changing the fluid bottle

– Disconnect the fluid tube from the lid by retracting the brass collar [9] and

removing the brass coupling [11].

– Remove the container from the tank housing of the Unique2.

– Unscrew the lid [10] of the empty container and screw it onto the new container.

– Place the full container into the tank housing.

– Push the brass coupling [11] into the brass collar [9], until you hear a click. The

brass collar is now locked firmly.

4.4 Fluid consumption

5. Operating the Unique2

From the finest mist to a thick haze, similar to fog, any desired effect can be

achieved. These haze effects form slowly so that the device should be switched

on some time before the lighting or the laser start to operate.

Important: Do not connect a ducting to the nozzle of the Unique2. If a ducting

is connected directly to the machine the haze will be pushed back into it. This

may damage the machine. We cannot grant warranty in this case!

5.1 Selecting the location

The location in which the Unique2is to be operated must

– be dry,

– be free from dusty or polluted air,

– be free from vibrations,

– be a non-flammable place or surrounding,

– be well-ventilated with haze-free air keeping the ambient operating tempera-

ture between 50°F and 105°F and the relative humidity below 80%.

5.2 Putting into operation

Warning:Never connect the Unique2to a dimmer or switchpack! This may destroy

the machine.

a. Connect the power plug to an electrical outlet.

Make sure the outlet has the correct voltage for your

machine.

A P and two figures appear on the LED display [17].

b. After 60 Seconds, the Unique2is heated up. Press the Enter button [16] once to

start the haze process. The green Active LED [18] will be lit. After a short delay

the machine begins to haze.

After 30 Seconds the display will go dark. To re-activate it, press one of the

buttons on the display.

P 2 5

5.4 Control choices

dmx

active

XXX = address

PXX = pump

FXX = fan

P. = pause

(min) ·

F. = fogtime

(sec)

1. = pause

2./3./4. = level a

5./6./7. = level b

timer

profile

P 1 5

Fig. 2: Adjusting the fan output Fig. 3: Adjusting the DMX-start address

14: Mode button

15: Up/Down button

16: Enter button

17: Led display18: Active-LED, green

19: DMX-LED, yellow

dmx

active

XXX = address

PXX = pump

FXX = fan

P. = pause

(min) ·

F. = fogtime

(sec)

1. = pause

2./3./4. = level a

5./6./7. = level b

timer

profile

2 7 5

20: Profile/

Timer-LED, red

dmx

active

XXX = address · PXX = pump · FXX = fan

P. = pause (min) · F. = fogtime (sec)

1. = pause ·2./3./4. = level a ·5./6./7. = level b

timer

profile

F 7 5

Fig. 1: Adjusting the pump output

5.3 Switching the device off

a. Press the Mode button [14] till „OFF” appears on the

display. After 15 Seconds the machine will switch off

automatically. On the right bottom edge of the display

a red decimal point will appear.

You can also switch off the machine within these 15 Seconds by pressing the

Enter button [16].

b. When you switch off the DMX signal, the machine will be switched off

automatically after 15 Seconds.

Note:

Please make sure that the Unique2will not be disconnected too early to allow

the fan to run until the device has cooled down. This will ensure that no fluid

remains in the vaporizer to come out as droplets when the device is switched

on next time.

5. Operating the Unique2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Máquina de niebla de Look Solutions

Look Solutions

Look Solutions Power-Tiny Manual de usuario

Look Solutions

Look Solutions TINY S Manual de usuario

Look Solutions

Look Solutions Viper NT Manual de usuario

Look Solutions

Look Solutions Cryo-Fog Manual de usuario

Look Solutions

Look Solutions Cobra 3.1 Manual de usuario

Look Solutions

Look Solutions Tiny FX Manual de usuario

Look Solutions

Look Solutions Tiny F07 Manual de usuario

Look Solutions

Look Solutions Viper NT Manual de usuario

Look Solutions

Look Solutions Unique 2.1 Manual de usuario

Look Solutions

Look Solutions Unique 2.1 Manual de usuario

Look Solutions

Look Solutions Orka deLuxe Manual de usuario

Look Solutions

Look Solutions Viper 2.6 Manual de usuario

Look Solutions

Look Solutions Tiny CX Manual de usuario

Look Solutions

Look Solutions Cryo-Fog Manual de usuario

Manuales populares de Máquina de niebla de otras marcas

Antari

Antari ICE Manual de usuario

Boost

Boost BOOST-FOG400LED-BK Manual de usuario

Home Accents Holiday

Home Accents Holiday FM1000-ASH Manual de usuario

EuroLite

EuroLite ZEITGEIST FOG-1200 Manual de usuario

Dyna-Fog

Dyna-Fog CYCLONE ULTRA 2734 Manual de usuario

PROEL

PROEL DRAGO HEAVY PLFD150HY Manual de usuario

Sparklyn

Sparklyn Y846 Manual de usuario

Magicfx

Magicfx CO2 Gun Manual de usuario

Ibiza

Ibiza LSM500LAS Manual de usuario

Antari

Antari M-5 Manual de usuario

Venue Lighting Effects

Venue Lighting Effects ULTRA MINI-FOGGER Manual de usuario

High End

High End F-100 Manual de usuario

Chauvet

Chauvet ARENA 2100 FLEX Manual de usuario

Antari

Antari X FAZER Manual de usuario

Beamz

Beamz F1600 Manual de usuario

Sagitter

Sagitter SG ARS900C Manual de usuario

KISANKRAFT

KISANKRAFT KK-STF-480 Manual de usuario

Orion

Orion OT-U250PP Guía