LongSung Technology U6100 Manual de usuario
Document Name: U6100 User Manual
Page ２of 31
Contents
Contents..........................................................................................................................................................................２
1．Introduction.................................................................................................................................................................3
1.1 Overview .................................................................................. 3
1.2 Application scenario ........................................................................ 3
2. U6100 interfaces..........................................................................................................................................................4
2.1 U6100 interface summary ................................................................... 4
2.1.1 Test points...............................................................................................................................................................5
2.1.2 Board to board connector.....................................................................................................................................5
2.1.3 RF interface ............................................................................................................................................................9
2.2 Application note of U6100 interfaces ......................................................... 10
2.2.1 RF antenna interface...........................................................................................................................................10
2.2.2 Power supply and ground...................................................................................................................................10
2.2.3 USB interface........................................................................................................................................................11
2.2.4 USIM interface......................................................................................................................................................12
2.2.5 Micro SD card interface.......................................................................................................................................14
2.2.6 Audio interface......................................................................................................................................................15
2.2.7 PCM interface and SPI interface.......................................................................................................................17
2.2.8 UART interface.....................................................................................................................................................18
2.2.9 LED control ...........................................................................................................................................................19
2.2.10 Others..................................................................................................................................................................21
3. U6100 key features...................................................................................................................................................22
3.1 Internet access ........................................................................... 22
3.2 SMS ..................................................................................... 23
3.3 start-up mode switching .................................................................... 23
3.4 Extended Mass Memory .................................................................... 24
4. Application Illustration...............................................................................................................................................24
4.1 Dial-up procedure ......................................................................... 24
4.2 SMS ..................................................................................... 25
4.2.1 Message Format..................................................................................................................................................25
4.2.2 Set Message Storage Location..........................................................................................................................25
4.2.3 PDU Format..........................................................................................................................................................26
4.2.4 TEXT Format ........................................................................................................................................................27
4.2.5 SMS Service Center Address Setting...............................................................................................................29
4.3 Start-up Mode Switching ................................................................... 29
Appendix：Mechanical dimensions of U6100 ..................................................... 30
Page 3 of 31
1．Introduction
1.1 Overview
The LONGSUNG HSPA module U6100, powered by Qualcomm MSM6290 chipset, can be integrated into any devices
for 3G mobile applications. It provides audio, SMS and extended mass memory function as well as high speed internet
access to HSUPA, HSDPA and UMTS networks worldwide.
The U6100 module complies with the technical standard listed below:
·HSUPA
3GPP R6, up to 2Mbps UL Category 4
·HSDPA
3GPP R5, up to 7.2 Mbps DL Category 8
·UMTS
Up to 384 Kbps DL and UL
·EDGE
3GPP R4, Class 12, up to 236.8 Kbps DL and 118.4Kbps UL
·GPRS
Up to 85.6 Kbps DL and 42.8 Kbps UL
It supports the frequency bands: UMTS 850/1900/2100 MHz and GSM/GPRS/EDGE 850/900/1800/1900 MHz.
1.2 Application scenario
The HSPA module U6100 supports Audio, SMS, extended mass memory and Internet access functions. The application
of U6100 is as follows:
Page 4 of 31
Figure1-1 U6100 application scenario
2. U6100 interfaces
2.1 U6100 interface summary
The HSPA module U6100 supports for multimode operation: HSDPA, HSUPA, tri-band UMTS (850/1900/2100
MHz) and quad-band GSM (850/900/DCS1800/PCS1900 MHz). The size of U6100 is 45×24×4.6mm. And the
appearance is shown in Figure 2-1 and Figure 2-2.
Figure 2-1 The front view of U6100 Figure 2-2 The rear view of U6100
There is a group of test points on the front of U6100 which is shown as part 1 in Figure 2-1. The 60PIN board to
board connector is shown as part 3 in Figure 2-2, which is the main interface for application. An antenna pad and a RF
connector is shown as part 2 in Figure 2-1 and Figure 2-2.
Page 5 of 31
2.1.1 Test points
The test points of U6100 are shown in Figure 2-3, and the definition of each point is shown in Table 2-1.
Figure 2-3 Test points of U6100
Table 2-1 The definition of U6100 test points
SN Definition
1 USIM Card CLK
2 USIM Card Power
3 USIM Card Data
4 USIM Card Reset
5 USB Power Input
6 GND
7 USB DATA+
8 USB DATA-
9 U6100 Power Input
2.1.2 Board to board connector
A 60PIN board to board connector is provided to connect with other board for data communication, power supply and
some other function, which is a narrow pinch dual line patch socket. The ball pinch is 0.5mm, the width of the ball is
0.2mm, the stacking height of the connector is 2.0mm. The length of connection area for the connector is larger than
0.55mm which ensure the reliable connection for the header & socket. The dimension of the connector is shown in
figure 2-4. The value of parameter A, B and C is as follows:
A=18mm, B=14.5mm, C=1.85mm. It is recommended to use the AXK6F60345YJ, which is provided by NAIS, as the
header to connect with the socket.
Page 6 of 31
Figure 2-4 The dimension of board to board connector
To prevent the connector from damage of static electricity caused by plugging, it is better to use the ESD protection
device which should be close to the connector as possible.
PIN definition of board to board connector is shown in Table 2-2.
Figure 2-5 The 60PIN board to board connector of U6100
Page 7 of 31
Table 2-2 The definition of board to board connector
SN Definition Description Remark
1 VBAT Power Supply
2 VBAT Power Supply
3 VBAT Power Supply
4 VBAT Power Supply
5 VBAT Power Supply
6 VBAT Power Supply
7 GND Ground
8 GND Ground
9 MIC_P MIC Data+
MIC Interface
10 USB_DM USB Data-
USB Interface
11 MIC_N MIC Data-
MIC Interface
12 USB_DP USB Data+
USB Interface
13 GND Ground
14 GND Ground
15 EAROP Earphone Data+
Earphone Interface
16 GND Ground
17 EARON Earphone Data-
Earphone Interface
18 USIM_RESET USIM Reset USIM Interface
19 GND Ground
20 USIM_DATA USIM Data USIM Interface
21 VREG_EXTUSIM USIM Power USIM Interface
22 GND Ground
23 PCM_DOUT/GPIO[103] PCM Data Output PCM Interface,can be used as GPIO
24 PCM_CLK/GPIO[80] PCM CLK PCM Interface,can be used as GPIO
25 PCM_DIN/GPIO[14] PCM Data Input PCM Interface,can be used as GPIO
26 GND Ground
27 GND Ground
28
HKADC
External analog signal
detecting
Page 8 of 31
29
SDCC_DATA0/GPIO[32] Micro SD Data 0
Micro SD Interface,can be used as GPIO,
SDCC_DATA0, SDCC_CLK, SDCC_CMD
and VREG_MMC are compatible for MMC
card
30 GND Ground
31 SDCC_DATA1/GPIO[99] Micro SD Data 1 Micro SD Interface,can be used as GPIO
32
SDCC_CLK/GPIO[31] Micro SD CLK
Micro SD Interface,can be used as GPIO,
SDCC_DATA0, SDCC_CLK, SDCC_CMD
and VREG_MMC are compatible for MMC
card
33 SDCC_DATA2/GPIO[100] Micro SD Data 2 Micro SD Interface,can be used as GPIO
34
SDCC_CMD/GPIO[30] Micro SD Command
Micro SD Interface,can be used as GPIO.
SDCC_DATA0, SDCC_CLK, SDCC_CMD
and VREG_MMC are compatible for MMC
card
35 SDCC_DATA3/GPIO[101] Micro SD Data 3 Micro SD Interface,can be used as GPIO
36 GND Ground
37
VREG_MMC Micro SD Power
Micro SD Interface,can be used as GPIO.
SDCC_DATA0, SDCC_CLK, SDCC_CMD
and VREG_MMC are compatible for MMC
card
38 USIM_CLK USIM CLK
USIM Interface
39 USB_VBUS USB Power
USB Interface
40 GND Ground
41 SLIC_RESET/GPIO[60] SLIC Reset Reset for peripheral device, can be used as
GPIO
42 GND Ground
43 SLIC_INT/GPIO[59] SLIC Interrupt Interrupt for peripheral device, can be used as
GPIO
44 SPI_CLK/GPIO[57] SPI CLK SPI Interface, can be used as GPIO
45 VREG_MSMP VREG_MSMP voltage output
46 SPI_DOUT/GPIO[55] SPI Data Output SPI Interface, can be used as GPIO
47 GND Ground
48 SPI_DIN/GPIO[56] SPI Data Input SPI Interface, can be used as GPIO
49 PWM_OUT PWM Output
50 SPI_CS/GPIO[58] SPI CS SPI Interface, can be used as GPIO
51 VCOIN VRTC
52 KPD_PWR_N Power On
Page 9 of 31
53 EXT_RST_IN Reset
54 UART_TX/GPIO[95] Tx in UART UART, can be used as GPIO
55 GND Ground
56 UART_RX/GPIO[96] Rx in UART UART, can be used as GPIO
57 PCM_SYNC/GPIO[102] PCM Synchronous Signal PCM Interface, can be used as GPIO
58 LED_CTL_G The Green LED Control
59 GND Ground
60 LED_CTL_R The RED LED Control
2.1.3 RF interface
The U6100 module provides an interface for RF antenna which has two different modes for connection.
Connector mode: U6100 uses MURATA’s MM9329-2700RA1 RF connector on the rear side, it is recommend to use
MURATA’s MXTK92XXXXX as matching connector. Please refer to MURATA’s MXTK92XXXXX documents for
more information.
Solder pad mode: The antenna can also be soldered to the pad on the module which has a ground pad close to the
antenna pad.
The RF connector is shown in Figure 2-6.
Figure 2-6 The sketch map of RF connector
Page 10 of 31
2.2 Application note of U6100 interfaces
U6100 provides rich interfaces for secondary development by the 60PIN board to board connector, such as Micro
SD/T-Flash card interface (Compatible for MMC card), USIM card interface, USB interface, audio interface, UART
interface, PCM（Pulse Code Modulation) interface, SPI（Serial Peripheral interface) interface, power supply interface
and so on. The detail information will be described in the following sections.
2.2.1 RF antenna interface
The ground impedance of RF antenna is 50Ω. There are two different modes for connection.
A. Connector mode: Recommended, a connector is on the rear side of PCB board
B. Solder pad mode: Antenna pad and ground pad are on the front side of PCB board
It’s required to use RF cable of which the insertion loss should comply with:
• GSM850/900<1dB
• DCS1800/PCS1900<1.5dB
• UMTS2100/ UMTS1900/ UMTS850<1.5dB
And the gain of antenna should comply with the Table 2-3:
Table 2-3 Antenna gain requirements
Item Parameter
Gain (dBi)
GSM DCS UMTS
0.5 1 1
Type Omnidirectional antenna
2.2.2 Power supply and ground
There are two power supply input for U6100 module listed as follows:
1. DC +3.4V～+4.2V, for U6100 working voltage;
2. DC +5V, for USB working voltage;
The description of U6100 Power supply and GND pins is shown in Table 2-4 below.
The device does not operate at temperatures below -20°
Tabla de contenidos
Manuales populares de Unidad de control de otras marcas
Festo
Festo Compact Performance CP-FB6-E Manual de lista de piezas
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manual de usuario
JS Automation
JS Automation MPC3034A Manual de usuario
JAUDT
JAUDT SW GII 6406 Series Guía rápida
Spektrum
Spektrum Air Module System Manual de usuario
BOC Edwards
BOC Edwards Q Series Manual de usuario
