LogN HN-DR4PN2U Manual de usuario
HN-DR4PN2U
User Manual
HN-DR4PN2U User Manual
Contents
1Safety Precautions ............................................................................................. 1
2Introduction ........................................................................................................ 1
2.1 LED Status Description.......................................................................... 2
2.1.1 Front Panel ................................................................................. 2
2.1.2 Rear Panel.................................................................................. 3
3Hardware Installation ......................................................................................... 1
3.1 Choosing the Best Location for Wireless Operation.............................. 1
3.2 Connecting the ADSL Router ................................................................ 1
4Introduction to Web Configuration...................................................................... 2
4.1 Preparation before Login ....................................................................... 2
4.2 Logging In to the Router ........................................................................ 3
4.3 WAN Configuration ................................................................................ 4
4.3.1 Layer2 Interface.......................................................................... 4
4.3.2 WAN Service .............................................................................. 7
4.3.3 3G WAN Service....................................................................... 13
HN-DR4PN2U User Manual
1
1 Safety Precautions
Follow the instructions below to prevent damage to the device and the risk of fire or
electric shock:
Use the power adapter supplied with the unit and plug it into a suitably rated
power outlet.
Leave sufficient space around the Power adapter and Modem to allow the
free flow of air for heat dissipation. Do not cover the device ventilation slots
as this will result in the device overheating.
Do not install this device close to a heat source or in an area of high
temperature. Avoid exposure to direct sunlight.
Do not install in a damp environment or allow fluid to spill on the Modem or
Power Supply.
Only connect this device as specified in the Manual or installation Wizard.
Failure to observe these instructions can lead to the risk of fire or damage to
the equipment concerned.
Install in a well-ventilated dry environment on a stable surface.
2 Introduction
The Router supports ADSL2+ link with downstream up to 24 Mbps and upstream up
to 1 Mbps. It provides a simple and cost-effective ADSL Internet connection for a
private Ethernet. The Router combines high-speed ADSL Internet connection, 3G
WAN service, IP routing for the LAN, and wireless connectivity in one package. The
wireless network supports 802.11g/802.11b/802.11n. It can provide high access
performance application for the individual users, SOHOs, and small enterprises.
HN-DR4PN2U User Manual
2
2.1 LED Status Description
2.1.1 Front Panel
The following table describes the LEDs of the device:
LEDs Color Status Description
Green On The device is powered on and the device
operates normally.
On The device and is initiating.
Red Blink The software is upgrading.
Power
Off The device is powered off.
On The DSL line connection is established.
Blink slowly The DSL line is off.
ADSL Green
Blink quickly The DSL line is initiating.
On The Internet connection is established.
And the users can access the Internet.
Green
Blink Internet data is being transmitted.
Red On Authentication fails.
Internet
Off The device is not connected to the
Internet.
On The Ethernet interface is connected.
Blink Data is being transmitted through the
Ethernet interface.
LAN4-1 Green
Off The Ethernet interface is disconnected.
On WLAN is enabled.
Blink Data is being transmitted through the
Wireless interface.
WLAN Green
Off WLAN is disabled.
On Connection succeeds under Wi-Fi
Protected Setup.
WPS Green
Blink Negotiation is in progress under Wi-Fi
HN-DR4PN2U User Manual
3
LEDs Color Status Description
Protected Setup.
Off Wi-Fi Protected Setup is disabled.
On The connection of 3G or USB flash disk
has established.
Blink Data is being transmitted.
USB Green
Off The connection of 3G or USB flash disk
is disabled.
2.1.2 Rear Panel
The following table describes the interfaces of the device:
Interface Description
WLAN/WPS
If you press the button between 1s and 5s to enable
WLAN function.
Press the button for more than 5s to enable WPS
function.
ADSL RJ-11 interface, for connecting to the ADSL interface or a
splitter through a telephone cable.
LAN1-4 RJ-45 interface, for connecting to the Ethernet interface of a
PC or the Ethernet devices through an Ethernet cable.
USB USB port, for connecting the 3G network card or other USB
storage devices.
Power Power interface, for connecting to the power adapter. The
output of power adapter is 12 V DC, 1A.
Power switch.
Reset
To restore the factory default, keep the device powered on,
push a needle into the hole for about 1 second, and then
release.
HN-DR4PN2U User Manual
1
3 Hardware Installation
3.1 Choosing the Best Location for Wireless Operation
Keep the numbers of walls and ceilings to the minimum.
Consider the direct line between access points and workstations.
Building materials make difference.
Position the antenna for best reception.
Keep your product away (at least 1~2 meters) from electrical devices.
Keep wireless devices away from electrical devices that generate RF noise
such as microwave ovens, monitors, and electric motors.
3.2 Connecting the ADSL Router
Step 1 Connect the ADSL interface of the router to the MODEM interface of the
splitter through a telephone cable. Connect the phone to the PHONE
interface of the splitter through a cable. Connect the incoming line to the
LINE interface of the splitter.
The splitter has three interfaces:
LINE: Connect to a wall phone jack (RJ-11 jack).
MODEM: Connect to the ADSL jack of the device.
PHONE: Connect to a telephone set.
Step 2 Connect the LAN interface of the router to the network interface card
(NIC) of the PC through an Ethernet cable (MDI/MDIX).
Note:
Use the twisted-pair cables to connect with the hub or switch.
Step 3 Plug one end of the power adapter to the wall outlet and connect the
other end to the Power interface of the router.
The following figure shows the connection of the Router, PC, and telephones.
HN-DR4PN2U User Manual
2
4 Introduction to Web Configuration
4.1 Preparation before Login
Before accessing the Modem, ensure the communication between PC and Modem
is normal. Check the communication as follows.
Configure the IP address of the PC as 192.168.1.X (2~254), net mask as 255.
255.255.0, gateway address as 192. 168.1.1 (For customized version,
configure them according to the actual version).
Enter arp -a in the DOS window to check whether the PC can read the MAC
address of the Modem.
Ping the management IP address (192.168.1.1 by default) of the Modem.
HN-DR4PN2U User Manual
3
If the PC can read the MAC address of the Modem and can ping through the
management IP address of the Modem, that means the communication of the PC
and the Modem is normal.
Note:
When you manage the router through Web, do not cut off the power supply of
the router. Otherwise, the router may be damaged.
4.2 Logging In to the Router
To log in to the DSL Router, do as follows:
Step1 Open a Web browser on your computer.
Step2 Enter http://192.168.1.1 (default IP address of DSL router) in the address
bar. The login page appears.
Step3 Enter a user name and the password. The default username and
password of the super user are admin and password. The username
and password of the common user are user and user. You need not
enter the username and password again if you select the option
Remember my password. It is recommended to change these default
values after logging in to the DSL router for the first time.
Step4 Click OK to log in to the Web page. Otherwise, please click Cancel to
exit.
HN-DR4PN2U User Manual
4
After logging in to the DSL router as a super user, you can view, configure, and
modify all the settings, and diagnose the system.
4.3 WAN Configuration
4.3.1 Layer2 Interface
ATM Interface
Choose Advanced Setup > Layer2 Interface > ATM Interface , and the following
page appears.
Figure 1 DSL ATM interface configuration
In this page, you can add or remove the DSL ATM Interfaces.
Click the Add button to display the following page.
HN-DR4PN2U User Manual
5
Figure 2 ATM PVC configuration
In this page, you can set the VPI and VCI values, and select the DSL latency, link type
(EoA is for PPPoE, IPoE, and Bridge.), connection mode, encapsulation mode,
service category, and IP QoS scheduler algorithm.
VPI (Virtual Path Identifier): The virtual path between two points in an ATM
network, and its valid value is from 0 to 255.
VCI (Virtual Channel Identifier): The virtual channel between two points in
an ATM network, ranging from 32 to 65535 (1 to 31 are reserved for known
protocols).
Select DSL Latency: You may select Path0 and Path1.
Select DSL Link Type: You may select EoA (it is for PPPoE, IPoE, and
Bridge), PPPoA, or IPoA.
Select Connection Mode: You may select the Default Mode or the VLAN
MUX Mode.
Otros manuales para HN-DR4PN2U
1
Tabla de contenidos
Otros manuales de Módem de LogN
Manuales populares de Módem de otras marcas
US Robotics
US Robotics 3453C Manual de usuario
MaxTech
MaxTech Plug & Play Internal Voice/FAX/Data/SVD... Manual de usuario
Zte
Zte MF823 Manual de usuario
Four-Faith
Four-Faith F1403 Manual de usuario
Sierra Wireless
Sierra Wireless AIRLINK MP595W Manual de usuario
Gemtek
Gemtek WiMAX WIXFBR-103 Manual de usuario