Logic Controls KB5000 Series Manual de usuario
Model: KB5000
Programmable Keyboard
66 Programmable Keys
USER MANUAL
NOTICE
The manufacturer of the POS programmable keyboard makes no
representationsorwarranties, either expressedorimplied,byorwithrespect
to anything in this manual, and shall not be liable for any implied warranties
offitnessforaparticularpurposeorforanyindirect,specialorconsequential
damages. Information in this document is subject to change without notice
and does not represent a commitment on the part of the manufacturer.
FCC NOTICE
This device complies with Part 15 of FCC Rules. Operations is subject to
the following two conditions: (1) this device may not cause harmful
interference. and (2) this device must accept any interference received,
including interference that may cause undesired operation.
i
LOGICCONTROLS,INC.
355DentonAve
NewHydePark, NY 11040
TEL:(516)248-0400
FAX:(516)248-0443
Email:[email protected]
http://www.logiccontrols.com
TABLE OF CONTENTS
FEATURES...............................................................................1
CARTON CONTENTS..............................................................2
HARDWARE CONNECTIONS .................................................3
FUNCTIONAL TEST ................................................................5
UTILITY DISK CONTENTS......................................................7
INSTALLING THE KB5.EXE UTILITY PROGRAM ................... 8
STARTING THE KB5.EXE PROGRAM ....................................8
PROGRAMMING THE KB5000 KEYBOARD ...........................10
ADVANCED PROGRAMMING .................................................12
SPECIAL FEATURES OF THE KB5000 ...................................13
INTER-STRING DELAY ............................................13
MULTI-LEVEL DEFINITION ......................................14
SELF PROGRAMMING ............................................16
SPECIAL CONFIGURATIONS .................................................17
DATA TRANSFER MENU .........................................................19
PINOUTS .................................................................................21
SPECIFICATIONS ....................................................................22
ii
FEATURES
•66 programmable keys; 2 position programmable key lock
•Re-legendable / re-programmable keyboard
•Requires no TSR programs and thus avoids software crashes.
•Requires no expensive programming kits.
•Requires no battery. Holds data over 100 years.
•Multi-level key definition.
•Program variable inter-string delay.
•Self programmable with a single key stroke.
•Records and plays back up to 119 alphanumeric characters per key.
•Provides true keyboard wedge function that operates with or without the
normal computer keyboard connected.
•Uses highly reliable, full-travel, mechanical switches.
•Recognizes the XT, AT, PS/2-25 and PS/2 (models 50 to 95)* computers
automatically.
•Features an optional 2 track magnetic stripe reader:
- Reads tracks 1 and 2
- Built-in decoder and wedge interface
- Optional 3 track MSR available
•Provides optional output formats: Standard keyboard emulation (KB5000),
or RS232 (KB5000R).
•Supports the following character sets:
- all alphanumeric characters
- 12 function keys
- all IBM keyboard’s special keys (Shift, CTRL, Alt, ESC, etc.)
- 255 ASCII codes
•Permits simple field programmability.
•Downloads an entire 66 key template into the internal non-volatile memory
in just 7 seconds.
•Includes replaceable legend sheet.
•Built with spill-proof construction.
•Includes cable, legend sheet, and utility software.
* (XT, AT, PS/2 are registered trademarks of International Business Machines Corporation.)
1
2
CARTON CONTENTS
KB5000
1. POS keyboard, Model KB5000
2. Computer interface cable
3. Utility software disk
4. Legend label sheet
5. User’s manual
6. Key cap lifter
7. 2 keys for lock
KB5000M
(with optional Magnetic Stripe Reader)
1. POS keyboard, Model KB5000M
2. Computer interface cable
3. Utility software disk
4. Legend label sheet
5. User’s manual
6. Key cap lifter
7. 2 keys for lock
KB5000R
(RS232C interface for PC computers)
1. POS keyboard, Model KB5000R
2. Computer interface cable
3. RS232C Interface cable
4. Utility software disk
5. Legend label sheet
6. Power adapter (+5vdc)
7. User’s manual
8. Key cap lifter
9. 2 keys for lock
3
HARDWARE CONNECTIONS
The KB5000 can be connected to an IBM101 PC, XT, AT or clone
computer, PS/2 computer, or computer terminal. The following diagram
shows how the KB5000 connects to the computer and standard key-
board or other keyboard peripheral (magnetic stripe reader, scanner,
etc.). When the KB5000 is used in a stand alone configuration no
connections are made to J5.
NOTE:
Before making any connections it is always advisable to
turn off the computer.
A. Connecting the KB5000 or KB5000M to an IBM101 PC, XT, AT, or
clone computer’s keyboard port:
1. Use the supplied interface cable. Plug the 6-pin connector into J2
of the KB5000.
Plug the 5-pin connector into the computer’s keyboard port.
2. Connect the computer’s keyboard into J5 of the KB5000.
NOTE:
J1 and J6 are not used in this configuration.
B. Connecting the KB5000 to a PS/2 computer:
1. Use the supplied interface cable. Plug in the 6-pin DIN
connector of the interface cable into J2 of the KB5000.
To computer
keyboard port
To computer keyboard or
other keyboard wedge devices
4
2. Connect the 5 pin DIN connector of the interface cable into the 5
pin DIN of the AT-to-PS/2 adapter.
3. Plug the PS/2 connector of the adapter into the computer’s
keyboard port.
4. Connect the PS/2 keyboard into J1 of the KB5000.
NOTE 1:
J5 and J6 are not used in this configuration.
NOTE 2:
The AT-to-PS/2 adapter is not supplied but can be
ordered from the manufacturer.
C. Connecting the KB5000R to a PC serial port:
1. Connect one end of the RS232C interface cable to J6 of the
KB5000R. Connect the other end of the cable to the DB9 serial
port of the computer.
NOTE 1:
J1, J2, and J5 are not used in this configuration.
NOTE 2:
Programming the KB5000R must be done on a PC
computer using the keyboard port. When
programming is completed, remove the cable going
to J2 and install the RS232C interface cable into J6.
NOTE 3:
Before writing or saving the legend file be sure to
open the F3 menu and set the RS232C option to
YES. Make any changes necessary to the
communications protocol setup. See Special
Configuration on page 17.
NOTE 4:
A standard KB5000 can not be used in an RS232C
environment without factory modifications.
5
FUNCTIONAL TEST
For testing purposes, your KB5000 keyboard was pre-programmed with a
templatecalled KB5000.tpl. Shownatthe end of thissectionisthe KB5000
keyboard with the pre-programmed information for each key. The following
simple steps will verify that the KB5000 is in good working condition:
1. Follow the Hardware Connections procedure described earlier in
this manual to connect the KB5000 to your computer.
2. Turn on your computer.
3. At the DOS prompt, press the upper left key of the keyboard.
4. The keyboard is working correctly when the words “LOGIC
CONTROLS PROGRAMMABLE KEYBOARD, MODEL KB5000”
appears on the monitor. To verify if the other keys are working
simply press each key and verify that the information displayed
on the monitor matches the template shown at the end of this
section. To help you understand how to program the keyboard
with special function keys the arrow keys have been programmed
with their actual codes. Therefore they will not display information
when depressed at a DOS prompt. However, when you enter the
programmingutility and selectthe KB5000.tpl template andselect
those keys, the correct programming information will be present.
5. To verify if the magnetic stripe reader is working correctly in a
KB5000M model, hold a credit card with the magnetic stripe at the
bottom and facing the arrow mark. Slide the card through the
reader slot. Make sure the bottom card edge is continuously
touching and gliding along the reader slot surface. The recorded
datafrom the credit cardwillautomatically be displayed at theDOS
prompt.
6. To verify if a KB5000R (RS232 model) is working properly, it will
be necessary to use a communications program. Set the protocol
of the communications program to 9600 baud, no parity, and 8
data bits. Press the upper left key on the keyboard and verify that
“LOGIC CONTROLS PROGRAMMABLE KEYBOARD, MODEL
KB5000” is present.
6
LOGIC CONTROLS
KB5000
L1
L2
RET
U
ITE
COR
R
DEP
A
ME
N
S
T
NO
T
EN
T
BACK
SPACE
SIGN
ON/OFF
QUANTITY
789
456
123
000 .
LOGIC
CONTROLS
KB5000
KEYBOARD
SHIFT
ESC
MENU
PRICE
PRICE
VERIFY
TOP
INQUIRY
DATA
SEND
MFR
COUPON
STORE
COUPON
ITEM
CORRECT
MERCHAND
CREDIT
END OF
MERCHAND
CHECK
STORE
CREDIT
TRAVEL
CHECK
GIFT
CERT.
PAYMENT
CASH
AMER.
EXPRESS
VISA
MASTER
CARD
DISCOVER
7
UTILITY DISK CONTENTS
All KB5000 keyboards come with a utility software disk. This disk
contains several important files:
KB5D.EXE -Use this utility with or without the keyboard being
attached.It is used to program the keyboard.
For a complete description of how this program
works see the section “Programming the KB5000
keyboard”.
KB5000.TPL - This template was pre-programmed into the
keyboard and matches the legend shown on the
previous page. If you have any questions on how to
program a particular key you can refer back to this
template to see how it was originally programmed.
DL5.COM - This utility program allows you to download a stored
template without entering the KB5.EXE utility
program. Simply add the KB5 directory to the path
statement of the autoexec.bat file. When you want
to change the stored program simply type the
download command plus the file you want to write
into the keyboard. For example, to download a file
called lunch, you would type DL5 LUNCH.TPL and
press ENTER. The download program will take
approximately 7 seconds to over-write the existing
legend file and install the lunch file.
README.DOC - This document contains the latest information
which may not be included in the manual.
Otros manuales para KB5000 Series
4
Tabla de contenidos
Otros manuales de Teclado de Logic Controls
Logic Controls
Logic Controls KB5000 Series Guía rápida
Logic Controls
Logic Controls KB5000 Series Manual del propietario
Logic Controls
Logic Controls LK8000 Series Manual de usuario
Logic Controls
Logic Controls LK1800 Series Manual de usuario
Logic Controls
Logic Controls LK1600 Series Manual de usuario
Logic Controls
Logic Controls LK1800 Series Manual de usuario
Logic Controls
Logic Controls KB5000 Series Manual de usuario
Logic Controls
Logic Controls LK7000 Manual del propietario
Logic Controls
Logic Controls LK8000 Series Manual de usuario
Logic Controls
Logic Controls LK1600 Series Manual de usuario
