LockUP Employee Lock Manual de usuario
keypad body
Shared Use Functionality
LockUp Lock - Employee Lock
user manual
E
FUNCTION
LOCK
i
Table of Contents
Metal Door Installations __________________________________________ 2
Required Components __________________________________________ 3
Metal Door Mounting Types _____________________________________ 4
Surface Mount Metal Door Installation __________________________ 5
Recessed Cup Metal Door Installation ___________________________ 7
3-Hole Lock Plug Removal ______________________________________ 9
Padlock Hasp Removal __________________________________________ 10
Programming Instructions ______________________________ 12
Lock Interface Overview ________________________________________ 13
Key Guide _____________________________________________________ 13
Initializing Locks ______________________________________________ 14
Adding Additional Manager Flex Key(s) to a Lock System____________ 14
For Lost or Stolen Keys ________________________________________ 15
Shared Use Instructions _________________________________ 16
Operate with a User Code _______________________________________ 17
Operate with an ADA User Key ___________________________________ 17
Operate with a Manager Flex Key ________________________________ 18
Troubleshooting _______________________________________________ 20
Common Lock Indicators ________________________________________ 21
Lock Warning Indicators ________________________________________ 22
Battery Replacement ___________________________________________ 22
Overall Dimensions ____________________________________________ 23
Contact Information ___________________________________________ 24
Warranty
ii
LIMITED WARRANTY
Security People, Inc., dba Digilock (the “Company”) warrants to the original purchaser the products manufactured by the
Company (the “Product”) to be free of defects in material and workmanship, provided: (i) The Company has been notied
of such defects within two years of purchase date and been given the opportunity of inspection by return of any alleged
defective Product to the Company, or its authorized distributor, free and clear of all liens and encumbrances,
transportation prepaid, accompanied by the statement of defects and proof of purchase; and (ii) the Product has not been
modied, abused, misused, or improperly installed, maintained, and/or repaired during such period; and (iii) such defect
has not been caused by corrosion, exposure to moisture, or ordinary wear and tear. LockUp lock products are not designed
or intended for exterior use or where exposed to moisture. Any exterior use where exposed to moisture is not covered by
any warranties and voids any warranties. Any resulting damage caused by direct exterior exposure or moisture is at the
purchasers own risk.
This warranty does not cover any labor costs for installation, removal and/or re-installation of the product being serviced
or replaced under warranty. This warranty is strictly limited to product repair or replacement. This warranty does not cover
batteries, normal wear of parts and/or damage resulting from any of the following: improper installation, negligent use or
misuse of the product, use of improper voltage or current, use contrary to operating instructions, and/or disassembly, repair
or alteration by any person other than the Company service personnel.
The Company will not evaluate warranted product without rst obtaining a Return Merchandise Authorization (RMA)
number from the Company. Such returns must be prominently marked with the Return Merchandise Authorization number
and shipped prepaid (return shipping is the responsibility of the end-user). Under no circumstance is the Company liable
for incidental or consequential damages. The Company makes no other warranty, and all implied warranties including any
warranty of merchantability or tness for a particular purpose are limited to the duration of the expressed warranty period
as set forth above.
LIMIT ON LIABILITY
The Company’s maximum liability for any damages resulting from or caused by the Product, whether in contract, tort,
or otherwise is limited to the purchase price of the Product. In no event shall the company be liable for any incidental or
consequential damages of any nature arising from the sale or use of this Product, whether in contract, tort, or otherwise by
either use or purchase of the Product the user or purchaser agrees to this limit on the company’s liability.
Note: Should the Product be considered a consumer product as may be covered by the Magnusson Moss Federal Warranty
Act, please be advised that: (1) some states do not allow limitations on incidental or consequential damages or how long
an implied warranty lasts so that the above limitations may not fully apply; (2) this warranty gives specic legal rights, and
a buyer may also have other rights which may vary from state to state. For warranty service and shipping instructions,
contact the Company. The Company reserves the right to make changes in designs and specications or to make additions
or improvements on its products without notice and without incurring any obligation to incorporate them on products
previously manufactured. The Company is not responsible for any modication, addition or alteration to our products by
others. Purchaser agrees to indemnify and hold Company harmless from all claims causes of actions, lawsuits, administrative
actions, and damages (except as covered by the express limited warranty as set forth above) including reasonable attorney
fees and costs arising out of or pertaining to the Product.
1
Metal Door Installations
Metal Door Mounting Types
3-Hole Lock Plug Removal
Surface Mount Metal Door Installation
Padlock Hasp Removal
Recessed Cup Metal Door Installation
2
Required Components
3
LockUp Lock Parts
Note: Conrm that all lock parts are present. If there are damaged or missing parts contact your
LockUp Product Support Specialist.
Required Components
1-Rear Unit1-Front Unit 2-Locking Nuts Optional-Back Plate
Warning: Do not use an electric screw gun during installation of the
lock unless equipped with a torque adjuster, which must be set on a
low torque setting. Otherwise, damage may be caused to the lock.
Required Tools
3/8” Socket
(deep socket required)
Phillips Screwdriver
Head Size #1 & #2
Hack Saw Metal File
For padlock hasp removalFor lock installation
4
Single Point Latch
Recessed Cup with
Multi-Point Latch
Recessed Cup with
Single Point Latch
Note: See page 10 for additional
modications for this door type.
ADA HandleBox Locker Padlock Hasp
Note: See page 10 for additional
modications for this door type.
Standard Lift
LockUp is compatible with a majority of industry standard 3-hole conguration, latch and handle types.
Some door types may need disassembly or modications prior to installation.
Metal Door Mounting Types
Note: Prior to installation the door must be clear of any obstructions. See page 9 for door prep.
5
Surface Mount Metal Door Installation Steps
Surface Mount Metal Door Installation Parts
A
1-Front Unit
C
2-Locking Nuts
B
1-Rear Unit
Required Tools 3/8” Socket
(deep socket required)
Place the mounting screw posts of the front unit (A)
through the lock mounting holes on the front of the
door.
Step 1
While holding the front unit (A) against the front of the
door, place the rear unit (B) against the rear face of the
door. Align the mounting holes with the mounting screw
posts from the front unit (A).
Step 2
6
Follow the Programming section of this
manual on pages 12-15.
Step 6Step 5
NOTE: If during operation of the lock, the lock
emits 10 rapid beeps and 10 ashes of the LED
light, it is an indicator that the bolt/latch of the lock
is binding with the door strike plate and/or frame. If
this occurs, the door and/or strike plate may need
to be aligned or adjusted. It may also be an indica-
tor that the locking nuts are over tightened on the
screw posts.
Test the operation several times (as indicated
below) while the door is open. Close the door and
test the unit again. Make sure there is no binding
between the bolt/latch and the door strike plate and/
or frame. Adjust alignment if necessary.
To lock and unlock press: = then `
NOTE: Do not touch the rear unit connector pins
(male connector) against any metal or other conductive
surfaces. This may short the batteries and cause
damage to the lock.
NOTE: An audible triple beep and three ashes of
the LED light indicate that the lock was connected
properly. If you do not hear these beeps, separate the
units, press the “C” button on the keypad and reconnect
the front and rear units on the door.
Slide the front unit (A) and rear unit (B) together
making sure that the pins of the rear unit align with the
front unit (A) connector.
Step 3
Place the locking nuts (C) over the mounting screws
and tighten to secure the lock to the door.
Step 4
NOTE: Do not touch the rear unit connector pins
(male connector) against any metal or other conductive
surfaces. This may short the batteries and cause
damage to the lock.
7
Recessed Cup Metal Door Installation Parts
Note: Prior to installation the door must be clear of any obstructions. See page 9 for door prep.
Recessed Cup Metal Door Installation Steps
A
1-Front Unit
C
2-Locking Nuts
B
1-Rear Unit
Required Tools 3/8” Socket
(deep socket required)
Place the mounting screw posts of the front unit (A)
through the lock mounting holes on the front of the
door.
Step 1
While holding the front unit (A) against the front of the
door, place the rear unit (B) against the rear face of the
door. Align the mounting holes with the mounting screw
posts from the front unit (A).
Step 2
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
