LivePure LP485HUM Manual de usuario
Ultrasonic Humidier
Owner’s Manual
Models:
LP485HUM
(All Colors)
Form #LP485HUM
08012023
© 2023 Registered Trademark/ TM Trademark of LivePure LLC.
Manufactured exclusively for LivePure LLC.
All rights reserved.
READ AND SAVE THESE INSTRUCTIONS
English
Table of Contents
At a Glance
Warnings & Know Your Humidier ......................................... 2-3
Operating Your Humidier
Initial Setup ............................................................................ 4
Humidier Operation ......................................................... 5
Maintenance ......................................................................... 6-8
Humidier Assistance
Troubleshooting ................................................................. 9
Technical Support .............................................................. 10
Warranty ............................................................................................. 11-13
Thank you for purchasing the Ultrasonic Humidier from LivePure®
Company. Please read and save these instructions to receive the maximum benet and
performance from your humidier.
READ AND SAVE THESE INSTRUCTIONS!
Important Safety Instructions:
Read all instructions before using this humidier
• This humidier may not work properly on an uneven surface. ALWAYS place this
humidier on a rm, level, and water resistant surface.
• ALWAYS place the humidier at least six (6) inches away from walls, heat sources,
and electrical appliances such as stoves, radiators, or heaters.
• ALWAYS place the humidier in an area that is out of the reach of children.
• Before using the humidier, extend the cord and inspect for any signs of
damage. DO NOT use the product if the cord has been damaged.
• Do not use the product outdoors or in locations subject to rain, water, heat, re
or sun.
• Never wrap a power cord around product or other object. Doing so can stress
the cord in ways that can cause the cord to fray, crack, or crimp. This can present a
safety hazard.
• Protect power cord from liquids. Do not leave power cord near sinks, tubs,
toilets, or on oors that are cleaned with liquid cleaners. Liquids can cause a short
circuit.
• Ensure that all power cord connectors are securely and completely plugged into
receptacles.
• Do not use product if power cord shows corrosion or signs of overheating.
• To prevent possible overheating, do not cover the power cord with clothing or
other objects when the power cord is plugged into an electrical outlet.
• ALWAYS UNPLUG AND EMPTY the humidier when it is not in operation or while
it is being cleaned.
• Use only clean, cool tap water when lling the tank. DO NOT use hot water.
• Never add medication of any type to the water tank.
At a Glance
Warnings & Know Your Humidier
2
• You should never leave the unit unattended in a closed room. The room can
become saturated and leave condensation on walls and furniture. Always leave a
door partially open.
• This device complies with part 18 of the FCC Rules.
• To reduce risk of re, electric shock, or injury, place the unit and cord where it is
not likely to be tipped or bumped.
• Do not overll the humidier due to potential risk of electric shock.
• ALWAYS disconnect the product from power source before performing any
maintenance or cleaning.
At a Glance
Warnings & Know Your Humidier
3
Operating Your Humidier
Initial Setup
4
Initial Setup:
1. Remove the plastic bag covering from the humidier.
2. Unravel and straighten the cord before use.
3. Lift tank cover o of humidier. Figure 1
4. Fill the unit with clean, cool tap water. Do not ll past max ll line.
5. Place the tank cover back on the tank and secure it in place.
6. Plug the humidier into a wall outlet and start the unit.
Note: DO NOT pour any water into mist output tube.
Figure 1
Operating Your Humidier
Humidier Operation
5
Operating the Humidier
1. Touch the power button once and the humidier will output mist on low. LED
light will be green. Figure 2
2. Touch the power button a second time and the humidier will output mist on
high. LED light will be blue.
3. Touch the power button a third time to turn o the humidier.
Note: When water tank is empty, LED light will turn red.
Essential Oil Tray: We recommend adding a few drops of your favorite essential
oil to the essential oil tray for an aromatherapy experience. Figure 2 & Figure 3
Note: DO NOT add essential oil directly into the water tank.
Figure 2
LED Light/
Power Button
Essential Oil
Tray
Operating Your Humidier
Maintenance
6
Daily Maintenance:
Note: ALWAYS unplug the humidier from the electrical outlet before cleaning.
1. Turn o the humidier and unplug it from the wall outlet.
2. Remove the tank unit by pulling it straight o the humidier base. Figure 3
3. Turn the tank upside down and drain any water into a sink or tub. Shake the
unit gently to remove any remaining water.
4. Rinse the tank thoroughly with water, empty, and wipe with a dry, clean cloth.
5. Wipe the humidier base with a dry cloth if necessary.
6. Rell the tank as directed under Initial Set Up and resume use.
Figure 3
Essential Oil
Tray
Operating Your Humidier
Maintenance
7
Cleaning the Aroma Port:
Note: It is recommended to clean the aroma port and pad after every essential oil
use.
1. Turn o the humidier and unplug it from the wall outlet.
2. Press in on aroma port to release the tray. Figure 3
3. Remove the aroma pad and rinse it out or replace with a new one.
4. Use a damp, soft cloth to clean the inside of the tray.
5. Allow both the tray and the pad to air dry.
6. Insert pad into tray, laying at, and return tray to humidier.
Cleaning the Water Purifying Cartridge:
Note: It is recommended to clean the water purifying cartridge every 1-3 months,
depending on the water hardness.
1. Turn o humidier and unplug from wall outlet.
2. Remove top cover.
3. Grab handle and lift water tank out of the unit and empty.
4. Unscrew the water purifying cartridge from inside the tank. Figure 4
5. Submerge cartridge in white vinegar for 10 minutes.
6. Remove cartridge from white vinegar. Shake several times to remove any
remaining solution. Rinse with clean water.
7. Wipe o remaining water with a dry, clean cloth.
8. Screw the cartridge back into place, rell water tank as directed under Initial
Setup and resume use.
Figure 4
Operating Your Humidier
Maintenance
8
End of Season Maintenance:
1. Follow the instructions for weekly maintenance before storing the unit.
2. Ensure all parts are completely dry before storing the unit.
3. Store the unit in a cool, dry place.
4. Never store the unit with water in the tank.
LivePure is not liable for any damages of any kind resulting from misuse or
improper maintenance. Warranty is only valid when proper maintenance, as
stated in this user manual, has been followed, as warranties apply explicitly
to manufacturer’s defects only.
Weekly Maintenance:
1. Turn o the humidier and unplug it from the wall outlet.
2. Remove the tank unit by pulling it straight o the humidier base.
3. Turn the tank upside down and drain any water into a sink or tub. Shake the
unit gently to remove any remaining water.
4. Fill the water tank with a mixture of 1.3 liters of water and eight (8) ounces
of white vinegar. Leave the mixture in the water tank for 20 minutes, giving the
water tank a shake every few minutes. After 20 minutes, give the water tank a
nal shake and discard the mixture.
5. Rinse the water tank several times with clean water. Leave the tank cap o to
allow the water tank to dry completely.
6. Wipe the surfaces of the humidier base with a soft damp cloth.
7. Once all the parts are clean and dry, reassemble the humidier, rell the water
tank, and resume use.
Note: Daily and weekly maintenance is necessary to prevent the growth of
bacteria, mold, and fungi.
Humidier Assistance
Troubleshooting
9
Problem: Excessive Noise
Solution:
1. Check the water tank to make sure it is properly seated on the base.
2. Check the water tank to make sure there are no bubbles when the water tank
is full and running. If there are bubbles, turn the unit o until the bubbling stops.
When the bubbling has stopped, set the unit to the desired speed.
Problem: Humidier not working
Solution:
1. Make sure the power button is not set to “O”
Problem: Mineral buildup on the water tank or tray
Solution:
1. Refer to the section Maintenance.
Problem: Humidity output and water usage decreased
Solution:
1. Check the Power Button to make sure it is set to the desired humidity level and
speed.
2. Check the water tank to make sure there are no bubbles when the water tank
is full and running. If there are bubbles, turn the unit o until the bubbling stops.
When the bubbling has stopped, set the unit to the desired speed.
3. Clean any components that have mineral build-up. Refer to the section
Maintenance.
Tabla de contenidos
Otros manuales de Humidificador de LivePure
