Linksys SRW224P - 10/100 - Gigabit Switch Manual de usuario
A Division of Cisco Systems, Inc.
®
Model No.
WIRED
with WebView and Power over Ethernet
24-Port 10/100 + 2-Port Gigabit Switch
SRW224P
User Guide
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Copyright and Trademarks
Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco
Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2005 Cisco Systems, Inc. All
rights reserved. Other brands and product names are trademarks or registered trademarks of their respective
holders.
How to Use This User Guide
This User Guide has been designed to make understanding networking with the Switch easier than ever. Look for
the following items when reading this User Guide:
In addition to these symbols, there are definitions for technical terms that are presented like this:
Also, each figure (diagram, screenshot, or other image) is provided with a figure number and description, like
this:
Figure numbers and descriptions can also be found in the “List of Figures” section in the “Table of Contents”.
This exclamation point means there is a caution or warning and
is something that could damage your property or the Switch.
This checkmark means there is a note of interest and is something
you should pay special attention to while using the Switch.
This question mark provides you with a reminder about
something you might need to do while using the Switch.
word: definition.
Figure 0-1: Sample Figure Description
SRW224P-UG-51008 KL
WARNING: This product contains chemicals, including lead, known
to the State of California to cause cancer, and birth defects or other
reproductive harm. Wash hands after handling.
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Table of Contents
Chapter 1: Introduction 1
Welcome 1
What’s in this Guide? 2
Chapter 2: Getting to Know the Switch 3
The Front Panel 3
The Back Panel 4
The Side Panel 4
RJ-45 Ports 5
The Gigabit Expansion Ports 5
The Console Port 5
Chapter 3: Connecting the Switch 6
Overview 6
Pre-Installation Considerations 7
Hardware Installation 8
Placement Options 8
Uplinking the Switch 9
Chapter 4: Configuration using the Console Interface 10
Overview 10
Configuring the Switch through the Console Interface 11
Chapter 5: Configuring the Switch through the Web Utility 24
Overview 24
System Information 25
IP Config 31
Switch Config 33
QoS 43
DiffServ 50
Security 56
SNTP 65
Statistics 66
PoE 68
Spanning Tree 71
SNMP 75
IGMP 76
Maintenance 80
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Help 82
Appendix A: Fast Ethernet and Gigabit Ethernet 83
About Fast Ethernet 83
About Gigabit Ethernet 83
Appendix B: Cabling 84
Overview 84
Twisted Pair Cabling 84
Fiber Optic Cabling 84
Appendix C: Glossary 85
Appendix D: Specifications 88
Appendix E: Warranty Information 89
Appendix F: Regulatory Information 90
Appendix G: Contact Information 96
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
List of Figures
Figure 2-1: Front Panel 3
Figure 2-2: Back Panel 4
Figure 2-3: Side Panel 4
Figure 3-1: Typical Network Configuration 6
Figure 3-2: Attaching the Switch’s Rubber Feet 8
Figure 3-3: Attaching Brackets to the Switch 9
Figure 3-4: Mounting the Switch 9
Figure 4-1: Finding Hyperterminal 10
Figure 4-2: Connection Description 10
Figure 4-3: Password Screen 10
Figure 4-4: COM1 Properties 11
Figure 4-5: Login 11
Figure 4-6: Switch Main Menu 12
Figure 4-7: System Configuration Menu 12
Figure 4-8: System Information 13
Figure 4-9: Versions 13
Figure 4-10: General Information 13
Figure 4-11: Serial Port Configuration 14
Figure 4-12: CPU Performance 14
Figure 4-13: User and Password Settings 15
Figure 4-14: IP Configuration 16
Figure 4-15: IP Address Configuration Screen 16
Figure 4-16: HTTP 16
Figure 4-17: SNMP 17
Figure 4-18: Network Configuration/PING 17
Figure 4-19: File Management 18
Figure 4-20: Restore System Default Settings 19
Figure 4-21: Reboot System 19
Figure 4-22: Back to Main Menu 20
Figure 4-23: Port Status 21
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Figure 4-24: Port Configuration 21
Figure 4-25: PoE Main Menu 22
Figure 4-26: Power Configuration 22
Figure 4-27: Power Port Status 22
Figure 4-28: Power Port Configuration 23
Figure 4-29: Logout 23
Figure 5-1: Address Field 24
Figure 5-2: Password Screen 24
Figure 5-3: Sys. Info - System Description 24
Figure 5-4: Sys. Info - System Information 25
Figure 5-5: Sys. Info - System Mode 26
Figure 5-6: Sys. Info - Forwarding Database 27
Figure 5-7: Dynamic Address Screen 28
Figure 5-8: Static Address Screen 28
Figure 5-9: Sys. Info - Time Synchronization Screen 29
Figure 5-10: Sys. Info - CPU Performance 30
Figure 5-11: Sys. Info - Logout 30
Figure 5-12: IP Config - IP Address 31
Figure 5-13: Switch Config - Port Configuration 33
Figure 5-14: Edit Port Configuration Screen 34
Figure 5-15: Switch Config - VLAN 36
Figure 5-16: Adding/Editing VLAN Screen 37
Figure 5-17: Switch Config - VLAN Port 38
Figure 5-18: Switch Config - LAG Configuration 39
Figure 5-19: Create LAG Screen 40
Figure 5-20: LAG Broadcast Control Screen 40
Figure 5-21: VLAN LAG Configuration Screen 40
Figure 5-22: Switch Config - Port Mirroring 41
Figure 5-23: Switch Config - LACP 42
Figure 5-24: LACP Membership Screen 42
Figure 5-25: QoS - CoS Settings 44
Figure 5-26: QoS - Queue Settings 45
Figure 5-27: QoS - CoS to Queue 45
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Figure 5-28: QoS - IP Precedence/DSCP 46
Figure 5-29: QoS - IP Port 47
Figure 5-30: QoS - ACL Priority 48
Figure 5-31: QoS - Rate Limit 49
Figure 5-32: DiffServ - Diffserv Class Map 51
Figure 5-33: DiffServ Class Map - Setting Rules 51
Figure 5-34: DiffServ Class Map - Adding a Class 52
Figure 5-35: DiffServ - Diffserv Policy Map 53
Figure 5-36: DiffServ Policy Map - Adding a Policy 53
Figure 5-37: DiffServ Policy Map - Setting Rules 54
Figure 5-38: DiffServ - Diffserv Service Policy 55
Figure 5-39: Security - ACL Conf 56
Figure 5-40: ACL Conf - Adding/Editing Standard ACL 57
Figure 5-41: ACL Conf - Adding/Editing Extended ACL 57
Figure 5-42: ACL Conf - Adding/Editing MAC ACL 59
Figure 5-43: Security - ACL Port Binding 60
Figure 5-44: Security - 802.1x Users 61
Figure 5-45: Security - 802.1x Port Conf 62
Figure 5-46: Security - RADIUS Server 62
Figure 5-47: Security - Port Security 63
Figure 5-48: Security - Storm Control 63
Figure 5-49: Security - HTTPS Settings 64
Figure 5-50: Security - System Password 64
Figure 5-51: SNTP - Global Settings 65
Figure 5-52: Statistics - Interface Statistics 66
Figure 5-53: Statistics - Etherlike Statistics 67
Figure 5-54: Statistics - RMON Statistics 67
Figure 5-55: PoE - Power Config 68
Figure 5-56: PoE - Power Port Config 69
Figure 5-57: PoE - Power Port Status 69
Figure 5-58: PoE - Power Status 70
Figure 5-59: Spanning Tree - Information 72
Figure 5-60: Spanning Tree - Configuration 73
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Figure 5-61: Spanning Tree - Port/LAG Info 73
Figure 5-62: Spanning Tree - Information 74
Figure 5-63: SNMP - SNMP Config 75
Figure 5-64: IGMP - IGMP Conf 77
Figure 5-65: IGMP - IGMP Router Info 78
Figure 5-66: IGMP - IGMP Router Conf 78
Figure 5-67: IGMP - IP Multicast Reg Table 79
Figure 5-68: IGMP - IGMP Member Conf 79
Figure 5-69: Maintenance - Reset 80
Figure 5-70: Maintenance - File Download 80
Figure 5-71: Maintenance - File Upload 81
Figure 5-72: Maintenance - Restore Defaults 81
Figure 5-73: Maintenance - Save Config 81
Figure 5-74: Maintenance - Integrated Cable Test 82
Figure 5-75: Help 82
1
Chapter 1: Introduction
Welcome
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
Chapter 1: Introduction
Welcome
Thank you for choosing the 24-port 10/100 + 2-Port Gigabit Switch with WebView and Power over Ethernet. This
Switch will allow you to network better than ever.
This new Linksys rackmount Switch delivers non-blocking, wire speed switching for your 10 and 100 megabit
network clients, plus multiple options for connecting to your network backbone. Twenty-four 10/100 ports wire
up your workstations, while the two integrated 10/100/1000BaseTX ports connect to other switches and the
backbone at Gigabit speeds. And the mini-GBIC ports allow future expansion through alternate transmission
media like optical fiber.
All the 10/100 ports on this Switch support IEEE 802.3af standard (802.3af) Power-over-Ethernet (PoE)
capabilities. Each port can detect connected 802.3af-compliant network devices, such as IP phones or wireless
access points, and automatically supply the required DC power.
The Switch can provide DC power to a wide range of connected devices, eliminating the need for an additional
power source and cutting down on the amount of cables attached to each device. Once configured to supply
power, an automatic detection process is initialized by the Switch that is authenticated by a PoE signature from
the connected device. Detection and authentication prevent damage to non-PoE devices.
The Switch features WebView monitoring and configuration via your web browser, making it easy to manage the
128 VLANs and up to 4 lagging groups. Or if you prefer, you can use the integrated console port to configure the
Switch. The non-blocking, wire-speed switching forwards packets as fast as your network can deliver them.
All ports have automatic MDI/MDI-X crossover detection. Each port independently and automatically negotiates
for best speed and whether to run in half- or full-duplex mode. Head-of-line blocking prevention keeps your high-
speed clients from bogging down in lower-speed traffic and fast store-and-forward switching prevents damaged
packets from being passed on into the network.
Use the instructions in this User Guide to help you connect the Switch, set it up, and configure it to bridge your
different networks. These instructions should be all you need to get the most out of the 24-port 10/100 + 2-Port
Gigabit Switch with WebView and Power over Ethernet.
2
Chapter 1: Introduction
What’s in this Guide?
24-Port 10/100 + 2-Port Gigabit Switch with Webview and Power over Ethernet
What’s in this Guide?
This user guide covers the steps for setting up and using the Switch.
• Chapter 1: Introduction
This chapter describes the Switch’s applications and this User Guide.
• Chapter 2: Getting to Know the Switch
This chapter describes the physical features of the Switch.
• Chapter 3: Connecting the Switch
This chapter describes how to connect the Switch.
• Chapter 4: Configuration using the Console Interface
This chapter instructs you on how to use the Switch’s console interface for configuring the Switch.
• Chapter 5: Configuring the Switch through the Web Utility
This chapter shows you how to configure the Switch using the Web Utility.
• Appendix A: Fast Ethernet and Gigabit Ethernet
This appendix describes the various types of ethernet.
• Appendix B: Cabling
This appendix discusses different types of cabling.
• Appendix C: Glossary
This appendix gives a brief glossary of terms frequently used in networking.
• Appendix D: Specifications
This appendix provides the Switch’s technical specifications.
• Appendix E: Warranty Information
This appendix supplies the Switch’s warranty information.
• Appendix F: Regulatory Information
This appendix supplies the Switch’s regulatory information.
• Appendix G: Contact Information
This appendix provides contact information for a variety of Linksys resources, including Technical Support.
Otros manuales para SRW224P - 10/100 - Gigabit Switch
2
Tabla de contenidos
Otros manuales de Cambiar de Linksys
Linksys
Linksys Instant EtherFast Series Manual de usuario
Linksys
Linksys SLM224P Manual de operación
Linksys
Linksys EZXS88R - EtherFast Rack Switch Manual de usuario
Linksys
Linksys EtherFast FENSK05 v2 Manual de usuario
Linksys
Linksys SR224G - Cisco - 10/100 Gigabit Switch Manual de operación
Linksys
Linksys EG008W - Instant Gigabit Workgroup Switch Manual de usuario
Linksys
Linksys ProConnect Series Manual de usuario
Linksys
Linksys SRW208MP Manual de operación
Linksys
Linksys ProConnect SVIEW08 v2 Manual de usuario
Linksys
Linksys EG008W - Instant Gigabit Workgroup Switch Manual de usuario
Linksys
Linksys SRW2048 Manual de operación
Linksys
Linksys LGS108P Manual de instrucciones
Linksys
Linksys SLM248G4S (G5) Manual de usuario
Linksys
Linksys SRW2016 Manual de usuario
Linksys
Linksys EG008W - Instant Gigabit Workgroup Switch Manual de usuario
Linksys
Linksys LGS105 Manual de instrucciones
Linksys
Linksys SLM248G4PS Manual de operación
Linksys
Linksys MGBLH1 - Gigabit LH Mini-GBIC SFP... Manual de usuario
Linksys
Linksys SVIEW04 - ProConnect CPU Switch KVM Manual de usuario
Linksys
Linksys LGS108P Manual de usuario
