Linksys SPA3102 Manual de usuario
Cluana
Linksys Cisco FXO adapter SPA 3102 Configuration guide
Cable connection
Step 1: connect your p one cable to t e “PHONE” port. Leave the “LINE” port disconnected.
Step 2: connect your LAN cable to t e “INTERNET” port. We assume a DHCP server is already running on
your LAN. If not, after step 3 jump to “Static IP configuration”
Step 3: power up t e adapter
IP address detection and web management
On your p one
–press **** (star key 4 time)
–press 110# and take note of t e annouced IP address. Let's call it “ip_address”
–press 7932# 1# 1 (it's needed to enable web management on t e internet port)
–open a web browser to t e URL: ttp://ip_address/admin/advanced
Adapter configuration
Let's assume t e followings:
Your PBX company domain is m compan .com (provided by Cluana).
Your PBX ostname is m server.cluana.com (provided by Cluana)
Your analog adapter User ID / Aut ID is fxo_1 (your c oice)
Your analog adapter password is : password (your c oice)
Your p one line PSTN number is YOUR_NUMBER (0733784374 in t e picture below)
Open SIP tab
RTP Parameters section
RTP Packet Size: 0.020
Open PSTN Line tab
Proxy and Registration
Proxy: m compan .com:5061
Outbound Proxy: m server.cluana.com:5061
Use Outbound Proxy: Yes
Register: Yes
Register Expires: 120
Subscriber Information
Display name: FXO_1
User ID: fxo_1
Password: password
Use aut ID: Yes
Aut ID: fxo_1
Audio Configuration
Preferred Codec: G711a (G711u for USA)
Dial Plans
Dial Plan 2: (S0<:YOUR_NUMBER>)
PSTN-To-VoIP Gateway Setup
PSTN Ring T ru Line 1: no
PSTN CID For VoIP CID: yes
PSTN Caller Default DP: 2
FXO Timer Values (sec)
PSTN Answer Delay: 2
PSTN Disconnect Detection
Disconnect Tone:
US: 480@-30,620@-30;4(.25/.25/1+2)
UK: 400@-30,400@-30; 2(3/0/1+2)
France: 440@-30,440@-30; 2(0.5/0.5/1+2)
Germany: 440@-30,440@-30; 2(0.5/0.5/1+2)
Net erlands: 425@-30,425@-30; 2(0.5/0.5/1+2)
Sweden: 425@-10; 10(0.25/0.25/1)
Norway: 425@-10; 10(0.5/0.5/1)
Italy: 425@-30,425@-30; 2(0.2/0.2/1+2)
Spain: 425@-10; 10(0.2/0.2/1,0.2/0.2/1,0.2/0.6/1)
Portugal: 425@-10; 10(0.5/0.5/1)
Poland: 425@-10; 10(0.5/0.5/1)
Denmark: 425@-10; 10(0.25/0.25/1)
New Zealand: 400@-15; 10(0.25/0.25/1)
Australia: 425@-13; 10(0.375/0.375/1)
International Control
FXO Port Impedance:
US: 600
EU (UK, Germany, Net erlands, Sweden, Norway, Italy,
Spain, Portugal, Poland, and Denmark): 270+750||150nF
France: 270+750||150nF
Australia: 220+820||120nF
New Zealand: 370+620||310nF
Press "Submit all c anges"
Now you can connect your p one line cable to t e “LINE” port.
Firmware Upgrade
Configuration parameters above were tested wit firmware release 5.2.13 . If your adapter is using an older
release (c eck Voice menu, Info->Product Information->Software Version) maybe a software upgrade is
needed.
•Download t e latest firmware from t e adapter manufacturer support site
•Extract t e Zip file, and t en run t e executable file to upgrade t e firmware.
•W en t e Firmware Upgrade Warning window appears, click Continue.
•In t e next window t at appears, enter t e IP address of t e ATA device, and t en click OK.
•In t e Confirm Upgrade window, verify t at t e correct device information and product number
appear. T en click Upgrade.
•A progress message appears w ile t e upgrade is in progress.
•T e success window appears w en t e upgrade is completed. T e device reboots. Click OK to close
t e confirmation message.
•To verify t e upgrade, point t e web browser to t e IP address of t e ATA device
Static IP configuration
We recommend to use a DHCP server on your Local Area Network in order to allow your adapter to
automatically configure its network parameters. S ould you need to assign a static IP address, please follow
t e Quick Install guide provided wit your adapter. Remember t at you need to find a free IP address
compatible wit your network and assign via IVR commands suc IP address and its netmask (eg.
192.168.1.100 and 255.255.255.0) . Suc parameters s ould be enoug to access t e device via web
browser and allow you to configure any ot er value.
Factor Reset
You can restore factory default settings wit t e following steps:
on your p one
–press **** (star key 4 time)
–press 73738#
–press 1
–angup
Otros manuales para SPA3102
5
Tabla de contenidos
Otros manuales de Adaptador de Linksys
Linksys
Linksys HU200 Manual de usuario
Linksys
Linksys PAP2-T Manual de usuario
Linksys
Linksys WPC54GX Manual de usuario
Linksys
Linksys PAP2-NA Guía rápida
Linksys
Linksys PLE200 - PowerLine AV EN Adapter Bridge Manual de usuario
Linksys
Linksys LNE100M Instrucciones de funcionamiento originales
Linksys
Linksys Small Business SPA2102 Manual de usuario
Linksys
Linksys USB1000 Manual de usuario
Linksys
Linksys WPC54GX Manual de usuario
Linksys
Linksys WUSB11 ver. 2.6 Manual de usuario
Linksys
Linksys Linksys SPA9000 Manual de usuario
Linksys
Linksys Small Business SPA2102 Manual de usuario
Linksys
Linksys PAP2-T Manual de operación
Linksys
Linksys PAP2 Manual de usuario
Linksys
Linksys WPC300N Manual de operación
Linksys
Linksys WPC54GR (DE) Manual de usuario
Linksys
Linksys PAP2 Manual de usuario
Linksys
Linksys EC1000 Manual de operación
Linksys
Linksys WUSB6100M Manual de usuario
Linksys
Linksys Small Business SPA2102 Manual de usuario
