Linksys WPC55AG Manual de usuario
A Division of Cisco Systems, Inc.
®
Model No.
Model No.
Quick Installation Guide
1
Model No.
Quick Installation Guide
WPC55AG (EU/LA/UK)
Notebook Adapter
Wireless A+G
Package Contents
• Dual-Band Wireless A+G Notebook Adapter
• Setup CD-ROM
• User Guide (English only) on CD-ROM
• Quick Installation
Dual-Band
Dual-Band
+
GHz
802.11a
5GHz
2
802.11g
4
,
2
1
AInsert the Setup Wizard CD-
ROM into your CD-ROM drive.
The Setup Wizard should run
automatically, and the
Welcome screen should
appear. If it does not, click the
Start button and choose Run.
In the field that appears, enter
D:\setup.exe (if “D” is the letter
of your CD-ROM drive).
BTo install the Adapter, click the
Install button on the Welcome
screen.
CAfter reading the License
Agreement, click Next to
accept the agreement
DChoose a network type. Select
5GHz or 2.4GHz if you will
connect to 802.11a, 802.11g,
and/or 802.11b networks.
Select 5GHz only if you will
connect only to 802.11a
networks. Select 2.4GHz only if
you will connect only to
802.11g and/or 802.11b
networks. Then click Next.
EChoose a wireless network
mode. Click the Infrastructure
Mode radio button if you want
your wireless computers to
network with computers on
your wired network using a
wireless access point. Click the
E
C
D
Set up the Dual-Band Wireless A+G
Notebook Adapter
B
IMPORTANT: You must run the
Setup Wizard before inserting the
Adapter into your notebook
computer.
3
Ad-Hoc Mode radio button if
you want multiple wireless
computers to network directly
with each other.
In the SSID field, enter the SSID
or name for your wireless
network. The SSID must be
identical for all devices in the
network. Click Next.
FIf you chose Infrastructure
Mode, go to Step G now.
Select the correct operating
channel for your wireless
network, which must match the
channel set on the other
devices in your wireless
network. If you are unsure
about which channel to use,
keep the default setting, Auto.
Then, click Next.
GSelect the security method you
want to use: WEP, WPA-
Personal, WPA-Enterprise,
RADIUS, or LEAP. Then click
Next.
If your network doesn’t use any
security method, select
Disabled and click Next. Then
proceed to Step I.
F
G
NOTE: WEP stands for Wired
Equivalent Privacy. WPA stands
for Wi-Fi Protected Access and is
a stronger security method than
WEP. RADIUS stands for Remote
Authentication Dial-In User
Service, and LEAP stands for
Lightweight Extensible
Authentication Protocol.
4
HProceed to the appropriate
instructions for your security
method.
1WEP
aSelect 64-bit, 128-bit, or 152-
bit from the drop-down menu
(152-bit encryption is available
only for 802.11a networking).
bEnter your Passphrase in the
Passphrase field, and the WEP
key will be automatically
generated.
To manually enter the WEP key,
leave the Passphrase field
blank and enter the WEP key in
the WEP Key field.
cClick Next, and go to Step I.
2 WPA - Personal
aSelect the encryption method
you want to use, TKIP or AES,
from the drop-down menu.
bEnter your Passphrase or pre-
shared key in the Passphrase
field.
cThen click Next and proceed
to Step I.
WEP
WPA - Personal
5
3 WPA-Enterprise
Select the authentication method
you want to use, EAP-TLS or PEAP.
EAP-TLS
aEnter the login name in the
Login Name field.
bEnter the name of the
authentication server in the
Server Name field. (optional)
cFrom the Certificate drop-
down menu, select the
authentication certificate.
dSelect the encryption method
you want to use, TKIP or AES.
eClick Next, and go to Step I.
PEAP
aEnter the login name in the
Login Name field.
bEnter the password in the
Password field.
cEnter the name of the
authentication server in the
Server Name field. (optional)
dFrom the Certificate drop-
down menu, select the
authentication certificate.
eSelect the authentication
method used inside the PEAP
tunnel, EAP-MSCHAP v2 or
Generic Token Card.
WPA - Enterprise
EAP-TLS
WPA - Enterprise
PEAP
6
fSelect the encryption method
you want to use, TKIP or AES.
gClick Next, and go to Step I.
4 RADIUS
Select the authentication method
you want to use, EAP-TLS or PEAP.
EAP-TLS
aEnter the login name in the
Login Name field.
bEnter the name of the
authentication server in the
Server Name field. (optional)
cFrom the Certificate drop-
down menu, select the
authentication certificate.
dClick Next, and go to Step I.
PEAP
aEnter the login name in the
Login Name field.
bEnter the password in the
Password field.
cEnter the name of the
authentication server in the
Server Name field. (optional)
dFrom the Certificate drop-
down menu, select the
authentication certificate.
eSelect the authentication
method used inside the PEAP
RADIUS
EAP-TLS
RADIUS
PEAP
7
ftunnel, EAP-MSCHAP v2 or
Generic Token Card.
gClick Next, and go to Step I.
5 LEAP
aEnter the user name in the User
Name field.
bEnter your password in the
Password field.
cEnter your password again in
the Confirm field.
dClick Next, and go to Step I.
IThe Setup Wizard will ask you to
review your settings before it
starts to copy files. Click Next to
save these settings, or click
Back to change any settings.
JIf you are using Windows 2000,
you may see a screen
indicating that a digital
signature was not found. This
software has been tested and
works properly with Windows
2000. Click the Yes button.
KAfter the software has been
successfully installed, the
Congratulations screen will
appear. Click Exit.
I
K
J
LEAP
8
2
APower down your notebook
and locate an available
CardBus slot on it.
BWith the connector pin end
facing the CardBus slot and
the label facing up, slide the
Adapter into the CardBus slot
until it locks into place.
CPower on your notebook
computer. The Power LED
should light up when the
Adapter is installed correctly.
DIf you are using Windows 2000,
you may see a screen
indicating that a digital
signature was not found. This
software has been tested and
works properly with Windows
2000. Click the Yes button.
EAfter the Adapter is installed,
the Wireless Network Monitor
icon will appear in the system
tray at the bottom right-hand
corner of your screen.
Double-click the icon if you
want to check the link
information, search for
available wireless networks, or
make additional configuration
changes.
Congratulations! The installation of
the Dual-Band Wireless A+G
Notebook Adapter is complete.
WPC55AG-EU-LA-UK_V1.2-QIG-50110NCJL
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2005
Cisco Systems, Inc. All rights reserved.
Connect the Dual-Band
Wireless A+G Notebook Adapter
B
DE
For additional information or troubleshooting
help, refer to the User Guide on the CD-ROM
or the Technical Support Insert. You can also
e-mail for further support.
Website
http://www.linksys.com/international
A Division of Cisco Systems, Inc.
®
Modelnr.
Modelnr.
Installationsvejledning
1
Modelnr.
Installationsvejledning
WPC55AG (DK)
Notebook-netværkskort
Trådløs-A+G
Pakkens indhold
• Trådløst dual band-A+G-Notebook-netværkskort
• Installations-cd-rom
• Brugervejledning (kun på engelsk) på cd-rom
• Installationsvejledning
Dual band
Dual band
+
GHz
802.11a
5
GHz
2
802.11g
4
,
2
1
APlacer cd-rom'en med guidet
konfiguration i cd-rom-drevet.
Den guidede konfiguration
køres automatisk, og
skærmbilledet Welcome
(Velkommen) vises. Hvis det
ikke er tilfældet, skal du klikke
på knappen Start og vælge
Kør. Indtast D:\setup.exe i det
felt, der vises (hvis "D" er
bogstavet for cd-rom-drevet).
BInstaller kortet ved at klikke på
knappen Install (Installer) i
skærmbilledet Welcome
(Velkommen).
CKlik på Next (Næste), når du
har læst licensaftalen, for at
acceptere vilkårene.
DVælg en netværkstype. Vælg
5GHz or 2.4GHz (5 GHz eller
2,4 GHz) for at tilslutte 802.11a-,
802.11g- og/eller 802.11b-
netværk. Vælg 5GHz only (Kun
5 GHz) for kun at tilslutte
802.11a-netværk. Vælg
2.4GHz only (Kun 2,4 GHz) for
kun at tilslutte 802.11g- og/eller
802.11b-netværk. Klik derefter
på Next (Næste).
EVælg en tilstand for det
trådløse netværk. Klik på
alternativknappen
Infrastructure Mode,
(Infrastrukturtilstand), hvis dine
trådløse computere, skal
oprette netværksforbindelse til
E
C
D
Konfiguration af det trådløse dual
band-A+G-Notebook-netværkskort
B
VIGTIGT: Du skal køre den
guidede konfiguration, inden du
sætter netværkskortet i din
notebook-computer.
Otros manuales para WPC55AG
6
Tabla de contenidos
Idiomas:
Otros manuales de Adaptador de Linksys
Linksys
Linksys USB100M Manual de usuario
Linksys
Linksys WAPPOE Manual de usuario
Linksys
Linksys PAP2T-NA Manual de servicio
Linksys
Linksys PAP2-NA Guía rápida
Linksys
Linksys PCM1000 - Cisco 10/100/1000 CARDBUS MOBILE... Manual de usuario
Linksys
Linksys Instant Broadband Series Manual de usuario
Linksys
Linksys PAP2 Instrucciones de funcionamiento originales
Linksys
Linksys PAP2 Manual de usuario
Linksys
Linksys WPC51AB Instrucciones de funcionamiento originales
Linksys
Linksys WPC200 Manual de operación
Linksys
Linksys WMP11 ver. 2.7 Instrucciones de funcionamiento originales
Linksys
Linksys WPC4400N Instrucciones de funcionamiento originales
Linksys
Linksys WPC54GS - Refurb Wrls-g Notebook Adr Spdbstr No... Manual de operación
Linksys
Linksys WPC54G EU Manual de usuario
Linksys
Linksys PAP2 Instrucciones de funcionamiento originales
Linksys
Linksys WUSB54GC EU Manual de usuario
Linksys
Linksys PLE200 - PowerLine AV EN Adapter Bridge Manual de operación
Linksys
Linksys WUSB54GS EU Manual de operación
Linksys
Linksys WUSB54GC EU Manual de usuario
Linksys
Linksys WPC54GR (DE) Manual de usuario
