Link-m-technologies WILO 900 Manual de usuario
WILO900 LOW RIDER REMOTE CONTROL SYSTEM
BY Link M Technologies
Owners Manual
Document 5.08.17-18
Revision 2.0
Introduction
Thank you for purchasing our product.
The WiLo 900 Low Rider Remote Control system was
designed with the input of low rider enthusiasts whose past
experiences with remote controls helped create a technical
wireless system into a simple form that will be a fun and
exciting addition to your pride and joy.
Link M Technologies
527 North Azusa Avenue #243
Covina, California 91722
http://www.linkmtechnologies.com
Table of Contents
CHAPTER 1..............................................1
GETTING STARTED ...................................1
CHAPTER 2..............................................2
SYSTEM OVERVIEW..................................2
Receiver Front Panel Controls.............2
Receiver Rear Panel.............................2
Interface Cable.....................................3
Transmitter Controls ............................4
CHAPTER 3..............................................5
INSTALLATION:QUICK .............................5
INSTALLATION:IN DEPTH.........................6
Suitable Location..................................6
Mounting ..............................................6
Connector Wiring List..........................7
Pump Example Wiring List...................8
Dump Example Wiring List ..................9
CHAPTER 4............................................10
SYSTEM OPERATION:QUICK ..................10
SYSTEM OPERATION:IN DEPTH..............11
Receiver Programming Setup.............11
Receiver Timing Setup........................11
Transmitter Operation........................12
Choreography Mode...........................12
Antenna Orientation...........................13
Transmitter Battery Replacement.......14
CHAPTER 5............................................15
TROUBLESHOOTING................................15
CHAPTER 6............................................16
SPECIFICATIONS .....................................16
LIMITED WARRANTY AND DISCLOSURE
STATEMENT............................................17
FCC NOTICE TO USER ............................18
INDEX.....................................................19
Getting Started
QuickreferencedwithIn Depth outlines.
his manual is outlined in two formats following the Overview section; “Quick” and
“In Depth”. The “Quick” format at the top of the chapter highlights the details of
the section for two purposes:
1. To provide the anxious user just enough information to get started right away
without having to glean the entire manual.
2. To refresh the memory of the one who has taken the time to read the entire manual.
The “In Depth” format provides all the operational details of the subject matter for the
enquiry minds as well as the product installers who need to know how the system
operates.
The System Overview section provides all the operating aspects of the transmitter and
receiver to briefly familiarize the user with the product.
Before You Begin
Parts Checklist
Make sure your package includes the following items:
1. WiLo 900TX handheld transmitter with antenna, batteries included.
2. WiLo 900RX receiver with right angle antenna.
3. 7’ Interface cable and assorted crimp terminals.
4. Two spare 3V size 2032 Lithium coin cell batteries.
5. Two spare mini blade 25 Amp fuses.
Chapter1
T
1
Chapter
2
System Overview
Receiver Front Panel Controls
Power
Push button On/Off switch lights up in center to indicate power.
Front
This variable timing control regulates how long the Front pump/s will stay ON minimizing over
extending the hydraulic cylinders. The pulse time can be adjusted from 35ms to 450ms.
Rear
Like the Front control, this variable timing control regulates how long the Rear pump/s will stay ON
minimizing over extending the hydraulic cylinders. The pulse time can be adjusted from 35ms to 450ms.
Program
Momentary push button switch used to “Learn” transmitter ID allowing system activation. See
Receiver Programming Setup for complete details.
Receiver Rear Panel
Fuses
Each solenoid control output is protected with a 25 Amp fuse that is shared between a respective
pump and dump pair.
Interface I/O connector
Output control signal and power input are provided via the interface connector.
2
Interface Cable
The Interface cables length is sufficient to mount the receiver in the trunk or on the rear
deck of the car.
Red 18AWG +12V input
Black 12AWG chassis GND
Red 10AWG +24V input
Brown Left Front Pump
Black Left Front Dump
Red Right Front Dump
Orange Right Front Pump
Yellow Left Rear Dump
Green Left Rear Pump
Violet Right Rear Pump
Blue Right Rear Dump
Figure 1: Interface cable length reduced for clarity.
3
Transmitter Controls
Function Switches
The transmitter has four 2 way Function switches labeled with the symbols; ♥♣♦♠.
Mode Switch
This slide switch on the bottom of the unit with the choice between “A” and “B”, changes
the action of the Function switches.
Power Switch
This switch is a momentary push button that turns the power ON to the unit as long as it is
held and is a safety feature to minimize accidental hydraulic activation.
Transmit LED
The LED below the antenna lights up when the Power switch is squeezed.
4
Chapter3
Installation: Quick
Someprideinworkmanship goes alongway for acleanandpresentable
installationto be proud of.
Important! Test your system before installation, then after installing the
Interface cable, then once more after connecting Interface cable to
WiLo900RX. Troubleshooting will be easier if a problem were to occur.
•Choose a suitable grounded location and mount the WiLo 900RX close
enough to the hydraulic control system so that the 7’ interface cable is
neatly routed between the two.
•Terminate the interface cable wires to power and the control solenoids
as illustrated in Figure 1.
•Plug the interface cable into the WiLo 900RX.
Power Program
Pumps
24
Pump Dump
Min Max Min Max
Los Controles
Pumpsolenoids
Dumpsolenoids
The receiver cable wiring
taps into the existing system at
the solenoid switches.
+24V
+24V
+12V
GND
Figure 2 Sample wiring diagram
5
Installation: In Depth
Therealnutsandbolts ofinstallations…
Suitable Location
The WiLo 900RX can be installed on the rear deck inside of the car or in the trunk, but
should be positioned such that:
•The interface cable neatly reaches the hydraulic control wiring or solenoids and
power source with enough slack left over to remove receiver should servicing be
needed.
•Mounting platform is grounded to vehicle chassis.
•The antenna is more than 6” horizontally from any metal such as batteries, pumps
and car chassis.
•The user can easily reach the unit to access controls.
Mounting
Always exercise caution and inspect underside trunk of a car checking for clearance to gas
tank and fuel lines before drilling holes and driving screws.
1. Mark the two mounting holes using the tabs as a guide.
2. Center punch and drill 1/8” holes on the vehicle chassis or a suitable grounded
platform.
3. Remove all metal shavings from holes before installing screws.
4. Position the receiver over the holes and drive one of the two supplied sheet metal
screws and washer to the right mounting tab (facing front).
5. Position interface cable Black ground wire over left mounting tab and drive second
screw and washer.
6
Connector Wiring List
Pin 12 Pin 3
Pin 10 Pin 1
The 12 pin male connector provides power to the receiver and output control signals to the
hydraulic control system via the 7’ interface cable.
Pin and Interface Cable wire list
Pin Wire color and function Pin Wire color and function
1 Red: Right Front Dump 7 Yellow: Left Rear Dump
2 Brown: Left Front Pump 8 Black 14AWG: Ground
3 Black: Left Front Dump 9 RED 10AWG: 24 Volt input
4 Orange: Right Front Pump 10 Green: Left Rear Pump
5 Red 18AWG: 12 Volt input 11 Blue: Right Rear Dump
6 RED 10AWG: 24 Volt input 12 Violet: Right Rear Pump
Note: Even though this system has been designed for a four pump four dump system,
controlling a single, double, or a three pump setup is just a matter of logical wiring.
See the Pump Example and Dump Example Wiring lists on the next two pages for various
single pump, two pump, and three pump wiring. These lists cover the basic and most
common setups because some systems are customized to the owners’ request.
7
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
