Linear Technology LT8608 Manual de usuario

DEMO MANUAL DC2521A

UG-1403 Rev. 0

DESCRIPTION

LT8608/LT8608B

42V, 1.5A Micropower

Synchronous Step-Down Regulator

Demonstration circuit 2521A is a 42V, 1.5A micropower

synchronous step-down regulator featuring the LT8608/

LT8608B. There are two assembly versions. DC2521A-A

is for the LT8608 and DC2521A-B is for the LT8608B.

The LT8608/LT8608B is a compact, high efficiency, high

speed synchronous monolithic step-down switching

regulator. Top and bottom power switches, compensa-

tion components and other necessary circuits are inside

of the 2mm × 2mm DFN package to minimize external

components and simplify design. The difference LT8608

and LT8608B is the LT8608 works under low ripple

Burst Mode

operation at light load condition, while the

LT8608B has pulse-skipping mode for light load. Due

to the Burst Mode operation, LT8608 consumes only

1.7μA of quiescent current when output is regulated at

5V. LT8608B has higher quiescent current because of its

pulse-skipping mode operation.

All registered trademarks and trademarks are the property of their respective owners.

PERFORMANCE SUMMARY

The demo board is designed for 5V output from a 5.5V

to 42V input. The wide input range allows a variety of

input sources, such as automotive batteries and industrial

supplies.

The demo board has an EMI filter installed. The radiated

EMI performances of the board (with EMI filter) are shown

in Figure 2 and Figure 3. The red lines in Figure 2 and

Figure 3 are CISPR 25 Class 5 peak limit. To use the EMI

filter, the input should be tied to VEMI, not VIN. An induc-

tor L2, which is a 0Ω jumper on the board by default

now, can be added in the EMI filter to further reduce the

conducted emission.

The LT8608 data sheet gives a complete description of

the part, operation and application information. The data

sheet must be read in conjunction with this demo manual

for DC2521A.

Design files for this circuit board are available.

Specifications are at TA= 25°C

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

VIN Input Voltage Range 5.5 42 V

VOUT Output Voltage 4.8 5 5.2 V

IOUT Maximum Output Current 1.5 A

fSW Switching Frequency 1.85 2 2.15 MHz

EFE Efficiency at DC VIN = 12V, IOUT = 0.75A 92 %

DEMO MANUAL DC2521A

UG-1403 Rev. 0

QUICK START PROCEDURE

DC2521A is easy to set up to evaluate the performance

of the LT8608/LT8608B. Refer to Figure 4 for proper

measurement equipment setup and follow the proce-

durebelow:

NOTE:When measuring the input or output voltage

ripple, care must be taken to avoid a long ground lead

on the oscilloscope probe. See Figure 5 for the proper

scope technique.

1. Set an input power supply that is capable of 42V/1.5A.

Then turn off the supply.

2. With power off, connect the supply to the input termi-

nals VIN and GND.

3. Turn on the power at the input.

NOTE:Make sure that the input voltage never

exceeds42V.

4. Check for the proper output voltage of 5V. Turn off the

power at the input.

5. Once the proper output voltage is established, connect

a variable load capable of sinking 1.5A at 5V to the

output terminals V

OUT

and GND. Set the current for0A.

a. If efficiency measurements are desired, an amme-

ter can be put in series with the output load in

order to measure the DC2521A’s output current.

b. A voltmeter can be placed across the output ter-

minals in order to get an accurate output voltage

measurement.

6. Turn on the power at the input.

NOTE:If there is no output, temporarily disconnect the

load to make sure that the load is not set too high.

7. Once the proper output voltage is established again,

adjust the load and/or input within the operating range

and observe the output voltage regulation, ripple volt-

age, efficiency and other desired parameters.

Figure 2. LT8608/LT8608B Demo Circuit EMI Performance in

CISPR 25 Radiated Emission Test, Antenna Polarization: Vertical

(VIN = 14V, VOUT = 5V, IOUT = 1.5A, 2MHz Switching Frequency)

LOAD CURRENT (A)

0.5

1.5

100

EFFICIENCY (%)

DC2521A F01

LT8608 (Burst Mode OPERATION)

LT8608B (PULSE-SKIPPING MODE)

Figure 1. Efficiency vs Load Current at 12V Input and 2MHz Switching Frequency

Figure 3. LT8608/LT8608B Demo Circuit EMI Performance in

CISPR25 Radiated Emission Test, Antenna Polarization:Horizontal

(VIN = 14V, VOUT = 5V, IOUT = 1.5A, 2MHz Switching Frequency)

DEMO MANUAL DC2521A

UG-1403 Rev. 0

QUICK START PROCEDURE

Figure 4. Proper Measurement Equipment Setup

Figure 5. Measuring Output Ripple

OUT

GND

DEMO MANUAL DC2521A

UG-1403 Rev. 0

PARTS LIST

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 1 C2 CAP., X7R, 4.7μF, 50V, 10% 1206 MURATA, GRM31CR71H475K

2 1 C4 CAP., X7R, 0.22μF, 16V, 10%, 0603 AVX, 0603YC224KAT2A

3 1 C5 CAP., C0G, 10pF, 25V, 5%, 0603 AVX, 06033A100JAT2A

4 1 C6 CAP., X7R, 47μF, 10V, 10%, 1210 MURATA, GRM32ER71A476KE20L

5 1 C7 CAP., X7R, 1.0μF, 25V, 10%, 0603 MURATA, GRM188R71E105KA12D

6 1 L1 IND., 2.2µH WURTH ELEKTRONIK, 74438336022

7 1 R2 RES., CHIP, 18.2k, 1/10W, 1%, 0603 VISHAY, CRCW060318K2FKEA

8 1 R3 RES., CHIP, 49.9k, 1/10W, 1%, 0603 VISHAY, CRCW060349K9FKEA

9 2 R1, R4 RES., CHIP, 1MEG, 1/10W, 1%, 0603 VISHAY, CRCW06031M00FKEA

10 1 R5 RES., CHIP, 187k, 1/10W, 1%, 0603 VISHAY, CRCW0603187KFKEA

DC2521A-A Version Specific Components

1 1 U1 IC, REGULATOR, DFN-8 ANALOG DEVICES, LT8608EDC#PBF

DC2521A-B Version Specific Components

1 1 U1 IC, REGULATOR, DFN-8 ANALOG DEVICES, LT8608BEDC#PBF

Additional Demo Board Circuit Components

1 1 C1 CAP., ALUM 22μF 63V SUN ELECT, 63CE22BS

2 2 C3, C10 CAP., X7R, 4.7μF, 50V, 10% 1206 MURATA, GRM31CR71H475K

3 1 C8 CAP., X7R, 1μF, 50V, 10%, 0805 TDK, C2012X7R1H105K

4 1 C9 CAP., X7R, 4.7μF, 16V, 10%, 0805 MURATA, GRM21BR71C475K73L

5 2 C11, C12 CAP., X7R, 0.1μF, 50V, 10%, 0603 MURATA, GRM188R71H104KA93D

6 1 FB1 FERRITE BEAD 0805 TDK, MPZ2012S221AT000

7 1 L2 RES., CHIP, 0Ω, 3/4W, 2010 VISHAY, CRCW20100000Z0EF

8 0 R6 (OPT.) RES., 0603

Hardware For Demo Board Only

1 7 E1 − E7 TESTPOINT, TURRET, 0.094" MILL-MAX, 2501-2-00-80-00-00-07-0

2 1 E8 (OPT.) TESTPOINT, TURRET, 0.094"

3 4 MH1 − MH4 STAND-OFF, NYLON 0.50 TALL KEYSTONE, 8833 (SNAP ON)

DEMO MANUAL DC2521A

UG-1403 Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

SCHEMATIC DIAGRAM

C C

B B

A A

ALL CAPACITORS ARE 0603.

NOTES: UNLESS OTHERWISE SPECIFIED

1. ALL RESISTORS ARE 0603.

SUNCON

63CE22BS

(2MHz)

ASSEMBLY TYPE

VERSION

DC2521A-A

DC2521A-B

LT8608EDC

LT8608BEDC

VCC

C12

0.1µF

50V

(Opt)

10pF

187k

C10

4.7µF

50V

1206

47µF

10V

1210

1.00M

EN/UV

U1 *

VIN

VCC

FB 5

PG 6

SW 2

BST 1

GND

22µF

63V

C11

0.1µF

50V

1µF

4.7µF

50V

1206

GND

1µF

50V

0805

2.2µH

74438336022

VIN

5.5V - 42V

18.2k

FB1

MPZ2012S221AT000

GND

0.22µF

0 2010

E7 PG

VOUT

5V / 1.5A

49.9k

GND

4.7µF

50V

1206

VEMI

5.5V - 42V

4.7µF

16V

0805

VOUT

DEMO MANUAL DC2521A

UG-1403 Rev. 0

 ANALOG DEVICES, INC. 2018

UG17098-0-9/18(0)

www.analog.com

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and

conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation

Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)

and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to

Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and

agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted

is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third

Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is

NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all

be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of

use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile

or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited

to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS

Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF

LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY

DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE

HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States

federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts

(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits

to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

Otros manuales para LT8608

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Linear Technology

Linear Technology

Linear Technology LTC3718 Manual de usuario

Linear Technology

Linear Technology LT6411 Manual de usuario

Linear Technology

Linear Technology DC2460A Guía de configuración rápida

Linear Technology

Linear Technology DC2159A Manual de usuario

Linear Technology

Linear Technology LTC2923 Manual de usuario

Linear Technology

Linear Technology CIRCUIT 630 Manual de usuario

Linear Technology

Linear Technology LTM9004 Manual de usuario

Linear Technology

Linear Technology DEMO CIRCUIT 1324A Manual de usuario

Linear Technology

Linear Technology LTC3588-1 Guía de solución de problemas

Linear Technology

Linear Technology DC2005A Manual de usuario

Linear Technology

Linear Technology LTC2933 Manual de usuario

Linear Technology

Linear Technology DC2455A-C Guía de configuración rápida

Linear Technology

Linear Technology LTC2430 Manual de usuario

Linear Technology

Linear Technology DC2041A Manual de usuario

Linear Technology

Linear Technology LTC6905 Series Manual de usuario

Linear Technology

Linear Technology LTC6930 Series Manual de usuario

Linear Technology

Linear Technology LTC3220 Manual de usuario

Linear Technology

Linear Technology DC2012A Guía de configuración rápida

Linear Technology

Linear Technology LTC2175-12 Manual de usuario

Linear Technology

Linear Technology LTC6417 Manual de usuario

Linear Technology

Linear Technology DC2339A Guía de configuración rápida

Linear Technology

Linear Technology DC1920A Guía de configuración rápida

Linear Technology

Linear Technology Analog Devices DC2773A-B Manual de usuario

Linear Technology

Linear Technology 1791A Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario