Lightware UMX-TPS-TX120 Manual de usuario

www.lightware.eu Firmware version: 1.0.1

For technical support contact support@lightware.eu Document revision: 1.1

UMX-TPS-TX120, UMX-TPS-TX130, UMX-TPS-TX140

Quick Start Guide

Introduction

Lightware’s new UMX-TPS-TX140 transmits universal video at a resolution up to 4K, audio

and control up to 170 m distance over a single CAT cable. This transmitter was designed for

digital and analog video and audio signals e.g. DVI, VGA, YPrPb, HDMI1.4 and DP 1.1 with

analog stereo audio from local inputs or embedded 7.1 HBR audio and to handle HDCP

encryption. The transmitters are fully compatible with Lightware TPS matrix boards and other

TPS products.

Installation

The transmitters can be powered locally with +12V DC adaptor (enclosed to the device), or

remotely by a PoE-compatible power injector, like Lightware’s TPS-PI-1P1.

Connecting steps –using local PSU

1. Connect the transmitter and the receiver unit by a CATx cable via the TPS connector.

2. Connect the desired HDMI / VGA / DVI / DP / Audio source(s) to the input connector(s) of the

transmitter.

3. Optionally connect the transmitter to a Local Area Network in order to control the device.

4. Optionally for RS-232 extension: connect a controller unit to the transmitter’s RS-232 port.

5. Optionally for Infra-Red extension:

a. Connect the IR emitter to the IR OUT port of the transmitter, and/or

b. Connect the IR detector to the IR IN port of the transmitter.

6. Connect the power cord of the supplied adaptor to the transmitter or use Lightware’s rack

mountable power supply unit.

7. Power on the devices.

Connecting steps –Using remote power

1. Connect the TPS OUT port of the transmitter to the TPS+PoE port of TPS-PI-1P1 by a CATx

cable.

2. Connect the receiver (or the Matrix input board) to the power injector by a CATx cable via the

TPS port.

3. Connect the desired HDMI / VGA / DVI / DP / Audio source(s) to the input connector(s) of the

transmitter.

4. Optionally connect the transmitter to a LAN in order to control the device.

5. Optionally for RS-232 extension: connect a controller unit to the transmitter’s RS-232 port.

6. Optionally for Infra-Red extension:

a. Connect the IR emitter to the IR OUT port of the transmitter, and/or

b. Connect the IR detector to the IR IN port of the transmitter.

7. Power on the devices.

Front view (UMX-TPS-TX140)

Rear view (UMX-TPS-TX140)

www.lightware.eu Firmware version: 1.0.1

For technical support contact support@lightware.eu Document revision: 1.1

UMX-TPS-TX120, UMX-TPS-TX130, UMX-TPS-TX140

Quick Start Guide

Front panel LEDs

VIDEO sources

▪DARK: video source is not selected

▪BLINKS: video source is selected but not active

▪LIGHTS: video source is selected and active

AUDIO sources

▪DARK: audio source is not selected

▪BLINKS: audio source is selected but not active –regardless of the output mode

▪LIGHTS (with short pause): audio source is selected and the port is active

(continuously): audio source is selected, active and the audio is embedded to the

output video stream

HDCP LED

▪DARK: video output signal is not encrypted with HDCP

▪LIGHTS: video output signal is encrypted with HDCP

AUTOSELECT LED

▪DARK: autoselect function is OFF

▪BLINKS: searching for signal (video LEDs also blink)

▪LIGHTS: active video signal is found (the LED of selected video also lights)

Rear panel LEDs

LIVE

▪DARK: device is not powered

▪BLINKS (slow): device is powered and operational

(fast): device is in bootload mode

▪LIGHTS: device is powered but no operation

RS-232

▪DARK: RS-232 ports (Local and Link) are in Pass-through mode

▪BLINKS: Command Injection mode is active

▪LIGHTS: RS-232 ports (Local and Link) are in Control mode

SRVC

▪LIGHTS: Testpattern is the selected and active input source

LINK

▪DARK: no TPS link between transmitter and receiver

▪BLINKS (slow): low power mode is active

(fast): Ethernet fallback mode is active

▪LIGHTS: TPS link is established, HDBaseT or Long Reach mode is active

Video input selection

Desired video input can be selected by the Video select button on the front panel. The selection

order of the inputs depend on the model. The input can be also selected by using LDC

(Lightware Device Controller), sending a protocol command, or using Autoselect.

Audio input selection

Desired audio input can be selected by the Audio select button on the front panel. The selection

order of the inputs depend on the model. The input can be also selected by using LDC

(Lightware Device Controller), sending a protocol command or using Autoselect.

Info: A port is active if there is a valid signal on it.

Allowed audio/video embedding

Audio source

HDMI

DVI-D

Audio1

(or Audio)

Audio2

Video source

HDMI



VGA



DVI-D



DVI-A



Info: If 4K video is selected to the output, analog audio cannot be embedded to the video stream

due to the capabilities of the video IC, thus the original audio stream will be transmitted.

Set dynamic IP address

1. Press and keep the Show me button pressed for 5 seconds; front panel LEDs start to blink.

2. Release the button, then press it 3 times quickly. DHCP is now enabled.

Restore factory default settings

1. Press and keep the Show me button pressed for 10 seconds; front panel LEDs start to blink.

2. Release the button, then press it 3 times quickly; factory default settings are restored:

IP address (fix)

192.168.0.100

Autoselect

disabled

DHCP

disabled

RS232 mode

Pass-through

Port nr.

6107

RS232 port setting

57600 BAUD, 8, N, 1

Crosspoint setting

Audio 1 input

Emulated EDID

Analog ports: F89

VGA input

Digital ports: dynamic

Otros manuales para UMX-TPS-TX120

Este manual sirve para los siguientes modelos

Otros manuales de Transmisor de Lightware

Lightware

Lightware DVI-OPT-TX110 Manual de usuario

Lightware

Lightware SW4-OPT-TX240RAK Manual de usuario

Lightware

Lightware UMX-TPS-TX130 Manual de usuario

Lightware

Lightware UMX-TPS-TX140 Manual de usuario

Lightware

Lightware UMX-TPS-TX120 Manual de usuario

Lightware

Lightware HDMI-TP-TX50 Manual de usuario

Lightware

Lightware HDMI-3D-OPT-TX210A Manual de usuario

Lightware

Lightware HDMI-TP-TX100R Manual de usuario

Lightware

Lightware SW4-TPS-TX240 Manual de usuario

Lightware

Lightware HDMI-3D-OPT-TX210A Manual de usuario

Lightware

Lightware UMX-OPT-TX150R Manual de usuario

Lightware

Lightware UMX-TPS-TX100 Series Manual de usuario

Lightware

Lightware HDMI-TPS-TX210 Manual de usuario

Lightware

Lightware DVI-OPT-RX110 Manual de usuario

Lightware

Lightware UMX-OPT-TX150R Manual de usuario

Lightware

Lightware WP-UMX-TPS-TX120-US Black Manual de usuario

Lightware

Lightware DVI-HDCP-TPS-TX210 Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario