Lightspeed TOPCAT Manual de usuario

Installation Guide

Instructional Audio System

Topcat

1. Do not use the apparatus near water.

2. Clean only with dry cloth.

3. Do not block any ventilation openings.

4. Do not install near any heat sources such as radiators, heat registers, stoves, or

other apparatus (including amplifiers) that produce heat.

5. Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding- type

plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not fit into your outlet, consult

an electrician for replacement of the outlet.

6. Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

7. Unplug this apparatus during lightning storms or when unused for long periods of

time.

8. Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power-supply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

9. When the mains plug or appliance coupler is used as the disconnect device, it shall

remain readily operable.

10. Please keep the unit in a good ventilation environment.

11. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus

to rain or moisture.

12. Apparatus shall not be exposed to dripping or splashing and no objects filled with

liquids, such as vases, shall be placed on the apparatus.

13. WARNING: Battery pack shall not be exposed to excessive heat such as sunshine,

fire or the like.

Important Safety Instructions

OVERVIEW

Table of Contents

OVERVIEW

2Important Safety Instructions

4System Components and Unpacking

5Optional Components

INSTALLATION

6Installation Planning

6Selecting Mounting Location

7Topcat Ceiling Installation (U.S. & Canada)

9Topcat Ceiling Installation (Outside U.S. & Canada)

12 Installing and Wiring Electrical Power

14 Alternate Power Connections

15 Setup and Using the Flexmike

16 Charging the Flexmike

INSTALLING OPTIONAL EQUIPMENT

17 PageFirst Installation

20 Media Connector Set-Up

24 Audio Input Cable Installation

CERTIFICATIONS & TROUBLESHOOTING

25 Safety Warnings and Certifications

28 Troubleshooting

OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING

System Components and Unpacking

The standard configuration includes:

Microphone Cradle Charger

& Power Supply

Flexmike

Volume Control Microphone

Topcat

OVERVIEW

NOTE ON PAIRING: Topcat, microphone(s), and Media Connector or Activate Station are paired together at the Lightspeed factory as required for proper operation.

OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING

Sharemike

Handheld Microphone

Optional Components

Media Connector

& Power Supply

Audio

Input Audio

Output Tone

Level

Push

StatusPower

Media

Connector

Activate Station

with Bluetooth

PowerLink

InputOutputMic

Optional equipment which may be part of your Topcat system:

INSTALLATION

SELECTING MOUNTING LOCATION

The Topcat is shipped ready to mount in a standard suspended ceiling grid. All hardware

needed to secure the Topcat into the ceiling grid is provided. Additional hardware may be

required if building structure tie-points are metal. A licensed electrician will need to provide

necessary materials if Topcat is permanently connected to the building AC mains.

Topcat will distribute sound throughout a classroom of up to 1200 sq  (112 sq m) with ceiling

heights of 9 to 12 . The location of the Topcat is critical to ensure even sound distribution.

1. Identify the center of the listening area of the classroom for optimum location (Figure 1).

2. Select a ceiling tile that is free of fixtures (lighting, HVAC, etc.) nearest to the center point.

3. Remove the selected ceiling tile for Topcat installation.

FIGURE 1:

IDENTIFY THE CENTER

OF THE LISTENING AREA

TOOLS AND MATERIALS

In addition to the contents of the Topcat system, you may need the following tools & materials:

• Flat blade screwdriver (small)

• Pliers

• Wire cutters

• Drill

Before beginning installation, make sure you have the necessary tools and materials on hand and that the area underneath the proposed Topcat location is cleared.

Installation Planning

NOTE: Topcat is designed for installation in a 2’ x 2’ or 2’ x 4’ suspended ceiling grid (or 600mm x 600mm international ceiling grids). If you do not have this type of ceiling,

please contact your local Lightspeed Territory Manager.

• Utility knife

• Safety wire anchors

• Wire ties

OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING

FIGURE 3:

SNAP THE T-BAR INTO PLACE TO CREATE A

1’ X 2’ OPENING AND A 3’ X 2’ OPENING

NEW T-BAR

EXISTING TILE GRID

3/4 TILE

TCQ

END SIDE

TOPCAT CEILING INSTALLATION (U.S. & CANADA)

The dimensions of Topcat are 1’ x 2’ and it is designed to fit into any

standard 2’ x 2’ or 2’ x 4’ suspended ceiling tile grid.

1. The ceiling tile will need to be cut to accommodate Topcat.

2. Set the ceiling tile on a flat work surface with the patterned side

facing down.

3. Using a straight edge, cut a 1’ x 2’ section from the ceiling tile,

leaving a 1’ x 2’ section and a 2’ x 3’ section (Figure 2), or two 1’ x 2’

sections (Figure 4).

5. Topcat dimensions

FIGURE 2:

CUT THE 2’ X 4’ TILE TO CREATE A 1’ X 2’

SECTION AND A 2’ X 3’ SECTION

WASTE REMAINING

3/4 CEILING TILE

CUT WITH

STRAIGHT EDGE

1’ 3’

2’

4’

2’ X 4’ CEILING TILE

FIGURE 4:

CUT THE 2’ X 2’ TILE TO CREATE

TWO 1’ X 2’ SECTIONS

WASTE

CUT WITH

STRAIGHT EDGE

1' 1'

2’

2’ X 2’ CEILING TILE

NEW T-BAR

EXISTING TILE GRID

1/2 TILE

FIGURE 5:

SNAP THE T-BAR INTO PLACE TO

CREATE TWO 1’ X 2’ OPENINGS

TCQ

4. Locate the 2’ ceiling grid T-bar provided. Locate the attachment

slots in the existing ceiling grid and snap the new T-bar into

place to create two openings to create a 1’ x 2’ and a 2’ x 3’

opening (Figure 3) or two 1’ x 2’ openings (Figure 5).

+DC INPUT

24V/2.5A

PAGING

INPUT AUDIO IN REGISTERPROGRAM

DO NOT DRILL IN THIS AREA

3.75”

11.5” 23 3/8”

FIGURE 1:

LOOP THE SAFETY WIRE THROUGH TAB

FIGURE 2:

PLACE TOPCAT INTO THE CEILING

GRID AND LOOP THE SAFETY WIRE

THROUGH BOTH TABS

CEILING

SECURING TOPCAT (U.S. & CANADA)

To comply with Building Codes, the Topcat MUST be secured with two

safety wires.

1. Locate the 20  length of safety wire. The safety wire needs to be permanently

attached to the solid building structure above.

2. Cut the safety wire in half, leaving two 10  pieces.

3. Install anchors (or eye screws if necessary) into the building structure.

4. Loop one end of the safety wire through the anchor (or eye screw), then twist it

around itself at least five times (Figure 1). Repeat for second anchor.

5. Li the Topcat up and lay it into the desired ceiling grid location.

CAUTION:Ensure that Topcat is stable on the grid rails with the side brackets

hooked over the rails. If not stable, there could be a danger of it falling until

safety wires are attached.

6. Loop the other end of the safety wire through one of the tabs on Topcat (located

in opposite corners). Pull the wire through until it is taut and twist it around itself

at least five times to secure Topcat. Cut o excess wire if needed.

7. When hard wiring AC power to Topcat, electrical codes require for Topcat to

be attached to the ceiling rail. Utilizing existing holes on the vertical section of

the ceiling rail (center of the hole to the base of the rail must be a minimum of

15mm) drill two screws on each 2’ side of the Topcat. Drilling these screws into

the designated areas of the Topcat chassis will not cause harm to the product

(Figure 3).

NOTE: Do not drill in the area designated with yellow tape.

8. Continue to page 12, Installing and Wiring Electrical Power.

FIGURE 4:

DRILL SCREWS THROUGH CEILING RAIL INTO DESIGNATED AREAS OF TOPCAT

ANCHOR OR

EYE SCREW

OVERVIEWINSTALLATIONOPTIONAL INSTALLATIONTROUBLESHOOTING

TOPCAT CEILING INSTALLATION (OUTSIDE U.S. & CANADA)

For 600mm x 600mm Ceiling Grid

Topcat has spacer brackets mounted on each of the four sides. With

these brackets installed and the ceiling tile is cut in half, the Topcat will

fit into a standard 2’ x 2’ suspended ceiling grid with an additional tile

support. With the brackets removed, it will fit a 300mm x 600mm ceiling

grid with an additional tile support (Figures 4 & 5).

Remove the spacer brackets from each of the four sides of the Topcat

(Figure 1, next page).

NOTE: If your ceiling grid is any other dimension than mentioned above,

contact your local Lightspeed Representative.

FIGURE 2

SNAP THE T-BAR INTO PLACE TO CREATE

A 1’ X 2’ OPENING AND A 3’ X 2’ OPENING

NEW T-BAR

EXISTING TILE GRID

3/4 TILE

TCQ

FIGURE 1

CUT THE 2’ X 4’ TILE TO CREATE A 1’ X 2’

SECTION AND A 2’ X 3’ SECTION

WASTE REMAINING

3/4 CEILING TILE

CUT WITH

STRAIGHT EDGE

1’ 3’

2’

4’

FIGURE 3:

CUT THE 2’ X 2’ TILE TO CREATE

TWO 1’ X 2’ SECTIONS

WASTE

CUT WITH

STRAIGHT EDGE

1' 1'

2’

NEW T-BAR

EXISTING TILE GRID

1/2 TILE

FIGURE 4:

SNAP THE T-BAR INTO PLACE TO

CREATE TWO 1’ X 2’ OPENINGS

TCQ

2’ X 4’ CEILING TILE 2’ X 2’ CEILING TILE

To comply with Building Codes, the Topcat MUST be secured with two

safety wires and to the ceiling grid with four screws.

1. Remove the spacer brackets from each of the four sides of Topcat (Figure 1).

2. Locate the 6m length of safety wire. The safety wire needs to be permanently

attached to the solid building structure above.

3. Cut the 6m safety wire in half, leaving two 3m pieces.

4. Install anchors (or eye screws if necessary) into the building structure.

5. Loop one end of the safety wire through the anchor (or eye screw), then twist it

around itself at least five times (Figure 2). Repeat for second anchor.

6. Li the Topcat up and lay it into the desired ceiling grid location.

CAUTION: Ensure that Topcat is stable on the grid rails. If not stable there

could be a danger of it falling until safety wires are attached.

7. Loop the other end of the safety wire through one of the tabs on Topcat

(located in opposite corners). Pull the wire through until it is taut and twist it

around itself at least five times to secure Topcat. Cut o any excess wire if needed

(Figure 3).

SECURING TOPCAT (OUTSIDE U.S. & CANADA)

FIGURE 1:

REMOVE SPACER BRACKETS

FIGURE 2:

LOOP THE SAFETY WIRE THROUGH TAB

FIGURE 3:

PLACE TOPCAT INTO THE CEILING

GRID AND LOOP THE SAFETY WIRE

THROUGH BOTH TABS

CEILING

ANCHOR OR

EYE SCREW

Otros manuales para TOPCAT

Tabla de contenidos

Otros manuales de Sistema estéreo de Lightspeed

Lightspeed

Lightspeed Lightspeed Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed 820iR Manual de usuario

Lightspeed

Lightspeed TOPCAT Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed 955Access Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed 705iR Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed Mobile PA Manual de usuario

Lightspeed

Lightspeed 975 Manual de usuario

Lightspeed

Lightspeed ActivateStation Manual de usuario

Lightspeed

Lightspeed 820iR Manual de usuario

Lightspeed

Lightspeed CAT 860 Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed flexcat Manual de usuario

Lightspeed

Lightspeed TOPCAT Manual de usuario

Lightspeed

Lightspeed Cat 855 Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed 800IX Manual de usuario

Lightspeed

Lightspeed Redcat media Manual de usuario

Lightspeed

Lightspeed Redcat Access LSRCA 1881 Manual de usuario

Lightspeed

Lightspeed 955 Access Manual de usuario

Lightspeed

Lightspeed 850iR Manual de usuario

Manuales populares de Sistema estéreo de otras marcas

LG CM3330B Manual de usuario

Sony

Sony SS-CEP50 Manual de usuario

Cetacea Sound

Cetacea Sound CVS-II Manual de usuario

Aiwa

Aiwa XR-H66MD Manual de usuario

Denon

Denon UCD-250 Manual de usuario

Sanyo

Sanyo DC-MX41i Manual de usuario

Sharp

Sharp CD-ES600V Manual de usuario

Exibel

Exibel BDX600-UK Manual de usuario

Sanyo

Sanyo DC-F320 Manual de usuario

Philips

Philips FWM583X Manual de usuario

Sharp

Sharp CD-C462 Manual de usuario

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Manual de usuario

Aiwa

Aiwa XR-EM70 Manual de usuario

Cyrus

Cyrus Lyric Manual de usuario

Philips

Philips MCM159/98 Manual de usuario

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Manual de usuario

RCA

RCA RS3965SB Manual de usuario

Sharp

Sharp XL-UH240 Manual de usuario