Lightspeed Delta X6 Manual de usuario
User Manual
Classroom Audio System
Delta X6
TABLE OF CONTENTS
SECTION 1: 4 System Components and Unpacking
Overview 5 Optional Components
6 Quick Start Guide
9 Top Panel Wireless Receiver Controls
10 Top Panel Controls & Connections
11 Rear Panel Controls & Connections
12 Installing or Replacing Receiver Module
SECTION 2: 14 Step 1. Connecting the Delta X6 Receiver to a
Power Supply
Set-up & Use 15 Step 2A. Setting up one DeltaX6 Receiver
16 Step 2B. Using More Than One Delta X6
Receiver
HANDHELD TRANSMITTER
17 Step 3. Channel Selection
18 Step 4. Mute & Sensitivity Levels
19 Step 5. Battery Life Indicator & Battery Type
20 Step 6. Replacing Batteries
21 Step 7. Recharging Batteries
BELT-PACK TRANSMITTER
22 Step 8. Connecting and Placing
23 Step 9. Channel Selection
24 Step 10. Mute and Gain Adjustment
25 Step 11. Battery Life Indicator and Type
26 Step 12. Replacing Batteries
27 Step 13. Recharging Batteries
28 Quick Start User’s Guide
29 Daily Use Instructions
SECTION 3: 30 Hand Held Microphone
Optional Accessories 31 Belt-Pack Transmitter
SECTION 4: 32 Troubleshooting Guide
Troubleshooting
SECTION 5: 34 Warranty Statement
Warranty &
Specifications
36 Safety Instructions & Warnings
37 System Specifications
4
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
SECTION 1:
OVERVIEW
SYSTEM COMPONENTS AND UNPACKING
The standard configuration of the Delta X6™ will contain:
Delta X6 Carry Case
Delta X6 Public
Address System
and Power Supply
HM-900 Transmitter
5
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troublshooting 5. Warranty, Safety
& Specifications
OPTIONAL COMPONENTS
Optional equipment which may be part of your Delta X6 system:
Individual Components
RX-7100R 100 Channel UHF Receiver Module
TX-HM900 100 Channel UHF Handheld Transmitter
AC-MH7 Mic Clip for HM900 Handheld Transmitter
TX-BP900 100 Channel UHF Belt-Pack Transmitter
BC-TX900 Battery Charger for BP900 or HM900
MC831S Audio-Technica 831 Lapel Mic
MC-TK270S Lightspeed Noise-cancelling Headset Mic
PS-15V-4.3 AC Power Supply
BA-NH1 AA NiMH Rechargeable Battery
AC-SPDELTA-X6 Carry Bag for Delta X6
AC-831CLIP Mic clip for MC-831S
AC-PWR-NA AC North American Power Cable
Optional Accessories
CA-GTC900 Guitar/aux In Cable for BP900
AC-TWBRK Speaker Stand Bracket
AC-SS1 Tripod Speaker Stand
AC-SPSS1 Carry Bag for Tripod Speaker Stand
MC-H10 Wired Dynamic Handheld Mic
BP-900 Transmitter and
Charger
MK-TK270S Noise-
Cancelling Headset
Microphone
MC-831S Audio
-Technica 831 Lapel
Mic
6
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ
RF
CHANNEL
LCD
Display
QUICK START GUIDE
System Overview
1. System Setup
Amplified
Audio Out
UHF Receiver
Module
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ
RF
CHANNEL
Use Scan
Button
to Select
Channel
Power Overview
LOW
BAT
LOW
BAT
Turn ON Power/
Wireless Mic 1
Volume Knob
7
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troublshooting 5. Warranty, Safety
& Specifications
QUICK START GUIDE CONT’D
2. Handheld Transmitter Setup
• Press and hold POWER to turn on.
• To set channel, press and hold SET
until cursor blinks on LCD display
(approximately 3 seconds).
• Use UP and DOWN to change
channel number.
• Press and hold SET to save
selected channel.
PWR
DN UP
PWR
D
NU
P
POWER
LCD Display
SET
UPDOWN
3. Belt-pack Transmitter Setup
• Press and hold ON for power.
• Open the plastic door by
depressing latches on each side.
• To set channel, press and hold SET
until cursor blinks on LCD display
(approximately 3 seconds).
• Use UP and DOWN to change
channel number.
• Press and hold SET to save
selected channel.
• Attach microphone into Mic Jack.
Belt Clip
LCD
Display
Mic Jack
On/Off
Button
Mute Switch
Red LED
CH: 002
CH: 002
694.500M
LS
HM-900
SENS SET
LEVEL [2]
NiMH
AKLN
CH: 002
CH: 002
694.500M
LS
HM-900
SENS SET
LEVEL [2]
NiMH
AKLN
CH: 002
CH: 002
694.500M
LS
HM-900
SENS SET
LEVEL [2]
NiMH
AKLN
CH: 002
CH: 002
694.500M
LS
HM-900
SENS SET
LEVEL [2]
NiMH
AKLN
Gain
Adjust
Door
Latch
Toggle
DOWN
Toggle
UP
Set
8
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
QUICK START USER’S GUIDE CONT’D
5. Final System Adjustment
• If your system contains
two wireless receivers and
microphones, do the following:
• Leave the first transmitter ON.
• Press SCAN on the second
receiver (Wireless Mic 2).
• Go to Steps 2 and 3 to program
the second transmitter.
WM 1 = Wireless Mic 1
WM 2 = Wireless Mic 2
LOW
BAT
LOW
BAT
RF Light indicates both
receiver module and
transmitter(s) are on
LightSPEED
7100R
UHF TRUE
DIVERSITY
RECEIVER
A B
LOW
BAT SCAN SQ
RF
CHANNEL
LCD
Display
4. Wired Microphone Setup Use AUX IN/MIC
IN to Control
Volume
LOW
BAT
LOW
BAT
MIC IN
Transmitter Location During Use
Do not stand directly in front of the
DELTA X6 with the microphone on.
Avoid!
9
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troublshooting 5. Warranty, Safety
& Specifications
LOW
BAT
LOW
BAT
LOW
BAT
LOW
BAT
TOP PANEL: WIRELESS RECEIVER CONTROLS
5. TRANSMITTER LOW BATTERY
INDICATOR: This LED will light
to indicate the batteries in the
corresponding transmitter are low.
6. SCAN: Press this button to auto-
matically select a channel that is
free from interference.
7. SQUELCH LEVEL ADJUSTMENT:
Covered with a plastic cap, the
squelch is adjusted at the factory
to provide the best signal level
and minimum noise. There is no
need to adjust the squelch level in
the field.
8. RECEIVER POWER/VOLUME
ADJUSTMENT: The receiver
volume adjustment is covered
with a plastic cap. The volume is
adjusted at the factory to provide
the best signal level and minimum
noise. There is no need to adjust
the receiver volume in the field.
1. WIRELESS RECEIVER: One or
two wireless receiver modules are
located at the top panel.
2. CHANNEL DISPLAY: An LED
readout of the receiver module
indicates which channel you are on.
3. CHANNEL CONTROL (0-99): The
left button controls the number
on the left (0-9). Each touch of
the button moves the number up
one until it gets to nine, and then
it cycles back to zero. The right
button has the same function for
the number on the right.
4. RF CHANNEL A/B INDICATOR:
The A lights up indicating the
A channel tuner is receiving the
strongest RF signal. The B lights
up indicating the B channel tuner
is receiving the strongest RF
signal.
1
1
2
36
5
78
4
10
1. Overview 2. Setup & Use 3. Optional
Accessories 4. Troubleshooting 5. Warranty, Safety
& Specifications
TOP PANEL CONTROLS AND
CONNECTIONS
1. BASS: Controls the level of low
frequency sound output for the
system.
2. TREBLE: Controls the level of high
frequency sound output for the
system.
NOTE: Reducing Feedback
The BASS and TREBLE controls
can be used to reduce feedback
(“squealing” or “howling”). If you
hear high-pitched squealing, lower
the treble setting. If you hear low-
pitched howling, lower the bass
setting.
3. AUX IN/MIC IN: Controls the
volume of a wired microphone
plugged into MIC IN on the back
of the system and the volume of
an auxiliary piece of equipment
plugged into the AUX IN on the
back of the system.
4. WIRELESS MIC 2: Controls the
volume of Wireless Microphone 2
(WM2) if a second wireless receiver
is installed.
5. POWER/WIRELESS MIC 1: Turn
this knob clockwise to power up
the system. Rotate to adjust the
volume of Wireless Microphone 1
(WM1).
6. POWER LED: Glows GREEN when
the system is powered on..
1
2
3
6
5
4
LOW
BAT
LOW
BAT
Otros manuales para Delta X6
2
Tabla de contenidos
Otros manuales de Micrófono de Lightspeed
