Liebert GXT3 RT120 Manual de usuario

1 SL-23180QS_Rev0_09-2012

Liebert®GXT3™

Quick Start Guide –500-3000VA RT120 & 3000RT208 & 1000MT120 Models

The Liebert GXT3 is shipped with the following items:

•Terminal Block Communication terminals

•Compact disc with:

oLiebert MultiLink®

oConfiguration program

oUser manual (electronic version)

•USB cable, one; 2m (6-1/2 ft.) long

•Rack handles with mounting hardware

•Plastic tower support base, one set

•Plastic Bezel

•Warnings, safety instructions booklet and WEEE recycling sheet (ISO 14001 compliance)

If the installation is in the Tower orientation, locate the support base and stand the UPS up on the support base. Note the

display should be located on the upper half of the unit in the Tower orientation and to rotate the display, grasp the sides

and rotate it 90 degrees clockwise. If the UPS is to be installed in a rack enclosure, follow the instructions provided with

the rack mounting hardware for proper installation.

If using an optional MicroPOD that was purchased separately, please see instructions shipped with the MicroPOD for the

installation instructions. This should be done before connecting the UPS to utility power.

If the hardwired MicroPODs are being used, conduit entry knockout are provided. Input and output wiring should be

installed in separate conduits. All wiring should be done in accordance to all local and national electrical codes. Before

wiring the UPS ensure that the breaker in the external upstream panelboard is OFF.

If an optional POD with attached input cord and output receptacles are used, connect the input plug receptacle and

connect the connected equipment to the output receptacles.

Plastic Bezel

Status Indicators

and Controls

Tower

Support

Base

Liebert GXT3 UPS

With

External Battery Cabinet

Liebert GXT3 UPS

2 SL-23180QS_Rev0_09-2012

The Liebert®GXT3™500-3000 VA models ship with the internal battery installed. Locate the plastic bezel from the

shipping box and attach the bezel to the UPS taking care to align the fastening clips on both ends before inserting them

into the holes.

If your application requires the use of external battery cabinets for longer back up time requirements, connect the first

battery cabinet to the UPS with the cable provided with the battery cabinet. Note: it does not matter which connector is

used on the battery cabinet. If more than one battery cabinet is used the additional cabinets then connect to the adjoining

battery cabinet.

To complete the installation of the UPS, simply connect the input plug on the attached 10 foot input cord to the proper wall

receptacle per the following table. Note: the 500-2000VA UPS models will now have power and the AC Input indicator on

the display should illuminate. The UPS will also begin to charge the internal batteries at this point, so there will also be

battery capacity LEDs illuminated.

UPS Model

Recommended

External Over

Current Protection

NEMA Input Plug

Provided

NEMA Input Plug

Provided

GXT3-500RT120

GXT3-700RT120

GXT3-1000RT120

GXT3-1500RT120

GXT3-1000MT120

15A

5-15

GXT3-2000RT120

20A

5-20

GXT3-3000RT120

30A

L5-30

GXT3-3000RT208

20A

L6-20

The Liebert GXT3 UPS is ready to be powered.

1. If an optional MicroPOD was used, ensure that the maintenance bypass switch is in the UPS position.

2. Install any optional Intellislot communication card into the Intellislot port on the rear of the unit.

3. Ensure the input breaker in the panelboard that provides input power to the UPS is closed

4. For 3000 VA models only, close the input breaker on the rear of the UPS unit. Note: the UPS will now have power

and the AC Input indicator on the display should illuminate. The UPS will also begin to charge the internal

batteries at this point, so there will also be battery capacity LEDs illuminated.

5. The Liebert GXT3 UPS has customizable settings that might be required depending on the application. Please

review the CD that ships with the UPS unit for the steps to use the configuration program and make any

necessary changes. Once that is complete, proceed to the next step.

6. If external battery cabinets are used, close all breakers on the rear of each battery cabinet

7. Press and hold for about 4 seconds, the “ON” button on the UPS display. Note: this will apply power to the output

receptacles via the internal bypass and the bypass indicator will be illuminated along with an audible beep.

8. Over the next several seconds the UPS will perform the self checks and startup routine then automatically

transfer the connected equipment to the inverter power. Once that is complete, the bypass indicator will turn off

and the inverter indicator will illuminate.

The UPS is now running in normal operation mode providing protected, filtered power to the connected equipment.

3 SL-23180QS_Rev0_09-2012

External Battery Cabinet

(for RT style units only)

Input Circuit Breaker

500-1500 VA RT120

2000 VA RT120

3000 VA RT120

3000 VA RT208

1000 VA MT120

External Battery Cabinet Connector

External Battery

Cabinet Connectors

Battery Circuit

Breaker

4 SL-23180QS_Rev0_09-2012

Troubleshooting

The following symptoms indicate the Liebert®GXT3™is malfunctioning:

•The relative indicators illuminate, indicating the UPS has detected a problem.

•An alarm buzzer sounds, alerting the user that the UPS requires attention.

In addition to the fault indicator being illuminated, one or more of LED segments of battery level indicator will also be

illuminated to provide a diagnostic aid to the user, as shown below

The descriptions are listed in the following table

Indicator

Diagnosis/Audible alarm

A - E

On bypass from output overload (half-second beep every half-second)

On bypass due to over temperature condition (1-second beep every 4 seconds)

On bypass due to DC bus overvoltage (1-second beep every 4 seconds)

On bypass due to DC/DC power supply failure (1-second beep every 4 seconds)

PFC failure (1-second beep every 4 seconds)

On bypass due to inverter failure (1-second beep every 4 seconds)

A&B

UPS Failure (includes dual-fan failure, single-fan failure under certain conditions and

battery charger failure) and continuous alarm

A&C

UPS failed battery test (2-second beep every 60 seconds)

A&E

Bypass feedback (1-second beep every 4 seconds)

B&C

REPO (one quarter-second beep at quarter-second intervals)

B&E

Short circuit on the output

C&E

UPS shutdown by command from communication (USB or Liebert IntelliSlot®port)

(no audible alarm)

AC Input Indicator

LED flashing

L-N reverse

Battery Indicator

Flashing

Internal battery source not available (continuous audible alarm); check battery

connection, power down and reboot UPS

Bypass Indicator

Flashing

Utility power voltage or frequency is out of tolerance; bypass is unavailable

Single-Phase UPS & Server Cabinets Technical Support

[email protected]

800-222-5877

Outside North America: +00800 1155 4499

Emerson Network Power Worldwide Locations

United States

1050 Dearborn Drive

P.O. Box 29186

Columbus, OH 43229

800-222-5877

Europe

Via Leonardo Da Vinci 8

Zona Industriale Tognana

35028 Piove Di Sacco (PD) Italy

+39 049 9719 111

Fax: +39 049 5841 257

Asia

29/F, The Orient Square Building

F. Ortigas Jr. Road, Ortigas Center

Pasig City 1605

Philippines

+63 2 687 6615

Fax: +63 2 730 9572

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Unión Postal Universal de Liebert

Liebert

Liebert PowerSure PSA 350VA to 1000VA Manual de usuario

Liebert

Liebert GXT3-5000RT230 Manual de usuario

Liebert

Liebert Liebert PS Manual de usuario

Liebert

Liebert GXT3-240TBATTCE Manual de usuario

Liebert

Liebert GXT2-10000RT208 Manual de usuario

Liebert

Liebert GXT3-5000RT208 Manual de usuario

Liebert

Liebert Series 600 Manual

Liebert

Liebert UPStation GXT 2U Manual de usuario

Liebert

Liebert PowerSure Personal Manual de usuario

Liebert

Liebert GHT MT+ Manual de usuario

Liebert

Liebert UPStation GXT 2U Manual de usuario

Liebert

Liebert NXL Manual de usuario

Liebert

Liebert 500-650 VA Manual de usuario

Liebert

Liebert Power Supply Manual de usuario

Liebert

Liebert APM 150 Manual de usuario

Liebert

Liebert GXT3 Manual de usuario

Liebert

Liebert 700 VA Manual de usuario

Liebert

Liebert 7400 Series Manual de usuario

Liebert

Liebert GXT3 5000RT208 Manual de usuario

Liebert

Liebert UPStation S VCR232C Guía rápida

Liebert

Liebert ITA 6kVA Manual de usuario

Liebert

Liebert UPSTATION GXT3X1-6000 Manual de usuario

Liebert

Liebert PowerSure Personal XT 450 Manual de usuario

Liebert

Liebert Series 300 Manual de instrucciones

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario