LG CordZero ThinQ R975GM Manual de usuario

Installing the Home Station

1. Remove the protective lm attached to the home station, the robot cleaner, and the nozzle.

2. Position the home station against a wall on hard, level ooring to prevent sliding during docking.

•Place the home station where there are no obstacles within 5 ft (1.5 m) of either side and within 6.5 ft (2 m) of

the front.

•Do not place the home station in conned spaces, as the robot cleaner will have di󰀩culty returning to the

home station.

3. Wrap the unwanted length of power cable around the cord keeper on the rear of the home station to prevent

the robot cleaner’s wheels from rolling over the cable.

4. Insert the power plug into an outlet.

5. Place the home station against the wall so that it does not move.

5 ft

(1.5 m)

5 ft

(1.5 m)

6.5 ft

(2 m)

Charging

1. Insert the power plug of the home station into a power outlet.

2. Turn on the robot cleaner’s main power switch .

3. Place the robot cleaner onto the charging terminals by aligning it to the front side of the home station.

•To return the robot cleaner to the home station during cleaning, press the Home button on the robot cleaner

or on the remote control. The robot cleaner moves to the home station to commence charging.

•If power is not supplied to the home station, the robot cleaner will not be charged.

Operation

Before Cleaning

•The robot cleaner can cross over thresholds that are up to 0.79” (20 mm) high depending on the shape and

material of the threshold.

•The robot cleaner will navigate back to the home station easily, if cleaning is started at the home station.

•Always keep the home station plugged in when in use. If the home station is not plugged in,the robot cleaner will

not return to the home station to charge automatically.

•Check the following items before use:

‒Remove cables or long strings from the oor.

‒Roll up or remove thin mats or carpets with pile longer than 1/2” (12 mm).

‒Remove fragile objects and obstacles from the oor.

‒Remove furniture with thin legs.

‒Close the doors of any room that you do not want the robot cleaner to enter.

Starting a Cleaning

1. Insert the power plug of the home station into a power outlet.

2. Press the Mode button to select the desired mode.

3. Press the Start/Stop button to start cleaning.

MEZ66331069

Rev.00_041320

Getting Started

Note

•Turn o󰀨 the main power switch on the robot cleaner before cleaning the robot cleaner.

•Unplug the power cord of the home station before cleaning the charging terminals of the home station.

•In order to maintain the optimum suction power of the robot cleaner, the lter should be cleaned at least once a

month or when dirty.

•To avoid odor, allow the dust bin, cyclonic mesh lter, pre-lter, and HEPA lter to dry completely in a well-ventilat-

ed area out of direct sunlight for at least 48 hours before reassembling.

Cleaning the Dust Bin, Cyclonic Mesh Filter, and Pre-Filter

1. Separate the dust bin, cyclonic mesh lter, and pre-lter from the product body.

2. Clean out the dust particles on the dust bin, cyclonic mesh lter, and pre-lter using a vacuum

cleaner or rinse them under running water.

•Remove any foreign substances on the rubber at the bottom of the dust bin.

•If the dust bin is completely full of dust or the lter is clogged, the suction power may be reduced.

Cleaning the HEPA Filter

1. Separate the HEPA lter from the HEPA lter case.

2. Clean the HEPA lter using a vacuum cleaner or rinse it under running water.

Cleaning the Brush

1. Separate the brush from the nozzle.

2. Remove any foreign substances such as hair and thread from the brush and brush ends.

•Dust may pile up at the brush entrance on the bottom surface. Remove dust from the brush entrance periodi-

cally using a brush or vacuum cleaner.

•If the brush contains foreign substances, the brush may not spin or a noise may occur during operation.

Cleaning the Sensors and Charging Terminals

1. Clean the 3D DUAL Eye, the cli󰀨 detection sensors, and the dust sensor using a cotton swab or a soft cloth.

2. Clean the charging terminals of the home station with a clean, dry cloth.

Maintenance

Tabla de contenidos

Otros manuales de Aspiradora de LG

Manuales populares de Aspiradora de otras marcas

Bissell

Bissell LittleGreen Proheat 1425 Series Manual de usuario

Panasonic

Panasonic MC-YL637S147-AE Manual de usuario

NEFF

NEFF N17XH10 0 Series Manual de usuario

Oreck

Oreck Cordless Captura BK51700 Series Manual de usuario

Kogan

Kogan KAVACROBVWA Manual de usuario

Kränzle

Kränzle VENTOS 50 ID Guía del usuario

EVVO

EVVO Ai35 Manual de usuario

DeWalt

DeWalt DWH200D Manual de usuario

Pontec

Pontec Pondomatic Vacuum Cleaner Manual de usuario

Cleanmaxx

Cleanmaxx PC-P007E Manual de usuario

Exido

Exido 240-114 Manual de usuario

RIDGID

RIDGID WD1685AU0 Manual de usuario

Ezviz

Ezviz RE4P Manual de usuario

STG global

STG global TANVAC HDV3000 Manual de usuario

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Manual de usuario

Factory

Factory M3340 Manual de usuario

Shop-Vac

Shop-Vac VN92 SERIES Manual de usuario

Nobles

Nobles 608669 Manual del producto