LG One:Quick Flex 43HT3WJ Manual de usuario

*MFL71848802*

(2111-REV00)

OWNER’S MANUAL

Stand

Please read this manual carefully before operating your set and retain it for future

reference.

ST-43HT

www.lg.com

Printed in Korea

ENGLISH

Assembling and Preparing

Accessories

ax 4

(M6 x L28)

* Image shown may dier from your product.

Safety instructions

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Please read these safety precautions carefully before

using the product.

• When lifting or moving the product, at

least two people are required due to the

heavy weight of the product.

- The product may fall down, causing a

malfunction or injury.

• Do not let children hang on or climb onto

the product.

- The product may fall down, causing an

injury or even death.

• Do not install the product in a place which

is unstable or vibrating or a place where

the product is not completely supported

such as a shaky shelf or a tilted place.

- The product may fall down or overturn,

causing an injury or malfunction.

• Put the product on a at and rm oor.

• When moving or handling a product

assembled with the Stand, be cautious

about damaging the exterior of the

product.

• When there is a stain or ngerprint left on

the surface, wipe it o gently.

- When removing a stain, do not

use excessive force. Wiping with

excessive force may cause scratches or

discoloration on the product.

ENGLISH

How to Assemble the Stand

• When assembling the stand, put the

product on a table or a at oor with its

screen facing downward. Here, rst put a

soft and uy cloth on the place, and then

put the product on top of it to prevent the

screen from being damaged.

• When assembling the stand, check if the

screws are completely fastened. (If they are

not completely fastened, the product may

lean forward after being installed.) Avoid

fastening the screws with excessive force

because otherwise the joint part of the

screws may be worn out, and the screws

might come o.

• When assembling the product, do not use

foreign substances (oil, lubricant, etc.) on

the screws.

- It may cause damage to the product.

• Before installing a wall mount support,

disassemble the Stand by conducting the

method to assemble the stand in a reverse

order.

2x 4

M6 x L28

ENGLISH

Mounting on a Table

1 Lift and tilt the monitor into its upright position

on a table.

• Leave a 10cm (3.9inches)(minimum) space

from the wall for proper ventilation.

10cm

(3.9inches)

2 Connect the power cord to a wall outlet.

• Do not apply foreign substances (oils,

lubricants, etc.) to the screw parts when

assembling the product. (Doing so may

damage the product.)

• If you install the monitor on a stand,

you need to take actions to prevent the

product from overturning. Otherwise, the

product may fall over, which may cause

injury.

• Do not use any unapproved items to

ensure the safety and product life span.

• Any damage or injuries caused by using

unapproved items are not covered by the

warranty.

• Make sure that the screws are inserted

correctly and fastened securely. (If they are

not fastened securely enough, the monitor

may tilt forward after being installed.) Do

not use too much force and over tighten

the screws; otherwise screw may be

damaged and not tighten correctly.

• Only use the authorized stand and wall

mounting bracket made specically for LG

products.

- Pursuant to Consumer Protection

Law, LG Electronics will not be

held responsible for any product

malfunction, material damage or

injury caused by using products not

authorized by LG Electronics.

Securing the Monitor to a Wall

1 Insert and tighten the eye-bolts, or monitor

brackets and bolts on the back of the monitor.

• If there are bolts inserted at the eye-bolts

position, remove the bolts rst.

2 Mount the wall brackets with the bolts to the

wall. Match the location of the wall bracket and

the eye-bolts on the rear of the monitor.

3 Connect the eye-bolts and wall brackets tightly

with a sturdy rope. Make sure to keep the rope

horizontal with the at surface.

• Use a platform or cabinet that is strong and large

enough to support the monitor securely.

• Brackets, bolts and ropes are not provided. You

can obtain additional accessories from your local

dealer.

Specications

ST-43HT

Model 43HT3WJ

Width x Depth x Height

(mm)

(inches)

420x242.3x241.4

(16.5x9.5x9.5)

Weight (kg)(lbs) 2.7

(5.9)

10cm

(3.9inches)

ENGLISH

Model

Serial No.

The model and serial number of the product

are located on the back and on one side of the

product. Record them below in case you ever

need service.

Otros manuales para One:Quick Flex 43HT3WJ

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Señalización digital de otras marcas

SMART-AVI

SMART-AVI SIGNAGEPRO Manual de usuario

KeyWest Technology

KeyWest Technology BREEZE Manual de usuario

XtendLan

XtendLan XL-DSP-183C Manual de usuario

Dynascan

Dynascan DS861LR4 Manual de usuario

Classic Exhibits

Classic Exhibits SEGUE DESIGNS MOD-1363 Manual de usuario

protech

protech KT-7290 Manual de usuario

WebDT

WebDT 515A Instrucciones de montaje

Samsung

Samsung IWJ Series Manual de usuario

EVERI

EVERI Enrollment Kiosk Manual de usuario

NCR

NCR SelfServ 90 Manual

ViewSonic

ViewSonic EP4602 Manual de usuario

ViewSonic

ViewSonic EP3202r Manual de usuario

Samsung

Samsung OM46N Manual de usuario

Viessmann

Viessmann 6336 Manual de usuario

Osram

Osram Traxon Manual de instrucciones de instalación

Philips

Philips Signage Solutions Series BDL4990VL Manual de usuario

ViewSonic

ViewSonic EP5012-L Manual de usuario

Philips

Philips CRD01/00 Manual de usuario