LG LGSWFAC81 Manual de usuario

S P E C I F I C A T I O N

Reg. Date : 2017.09.01 MODEL NAME: LGSWFAC81

Rev. No. : 1.0

2. Ordering Information

Model Description

LGSWFAC81 802.11 a/b/g/n/ac WiFi Module, Dual Band 2T2R MIMO

1. Electrical Specifications

1. Features

LGSWFAC81 is the small size and low power module for IEEE 802.11ac wireless LAN.

LGSWFAC81 is based on Realtek RTL8812BU solution.

IEEE 802.11 a/b/g/n/ac Dual Band WLAN infrastructure

Size : 48.0mm x 30.0mm x 7.95 mm

Two stream spatial multiplexing up to 300Mbps(802.11n) / 867Mbps(802.11ac)

WLAN Metal Press antenna

Use on-chip OTP (One-Time Programmable)

Host Interface : USB2.0 (WLAN)

- This model is using the common USB2.0 to control WLAN

Security : WFA WPA/WPA2, WPS2.0, WAPI

Application : DTV, Tablet/MID, Blue-ray Disk Player, USB Dongle

3. Product Picture

S P E C I F I C A T I O N

Reg. Date : 2017.09.01 MODEL NAME: LGSWFAC81

Rev. No. : 1.0

4. Absolute Maximum Ratings

Parameter Min Max Unit

Storage Temperature -20 +80 ℃

Storage Humidity (40℃)-90%

Caution : The specifications in Table 1 define levels at which permanent damage to the

device can occur. Function operation is not guaranteed under these conditions.

Operating at absolute maximum conditions for extend periods can adversely affect the

long-term reliability of the device.

. Other conditions

1) Do not use or store modules in the corrosive atmosphere, especially where chloride

gas, sulfide gas, acid, alkali, salt or the like are contained.

Also, avoid exposure to moisture.

2) Store the modules where the temperature

and relative humidity do not exceed 5 to 40℃and 20 to 60%.

3) Assemble the modules within 6 months.

Check the soldering ability in case of 6 months over.

< Table 1 >

S P E C I F I C A T I O N

Reg. Date : 2017.09.01 MODEL NAME: LGSWFAC81

Rev. No. : 1.0

5. Operating Conditions

Parameter Min Typ Max Unit

Ambient Temperature 0 - 60 ℃

Ambient Humidity (40℃)--85 %

Supply Voltage 3.135 3.3 3.6 Vdc

6. Standard Test Conditions

The Test for electrical specification shall be performed under the following condition

Otherwise this following conditions, not guaranteed this performance.

Temperature 25 ±5℃

Humidity 65 ±5%

Input power Supply Voltage

VCC_3.3V 3.135 ~ 3.6V

6-1. Ambient condition

6-2. Power supply voltages

6-3. Current consumption

Human Body Model (HBM) Min. Max. Unit

Contact - ±4kV

Air - ±15

6-4. ESD Information

Note 1 : IEC 61000-4-2 (150pF, 330R)

※Test condition : After 8-pin USB Cable connect to module, progress ESD test.

Current Consumption Min. Typ. Max. Unit

TX Mode ( 11ac/80MHz) - 700 1200

mAIdle and Associated state - 270 300

Radio disabled state - 60 70

Note 1 : This figure is the RMS(root mean square) Value.

S P E C I F I C A T I O N

Reg. Date : 2017.09.01 MODEL NAME: LGSWFAC81

Rev. No. : 1.0

7. Pin Description

Pin No. Pin Name I/O Pin Description

1 VCC I Power Supply 3.3V

2 USB D- I/O USB Communication signal USB D-

3 USB D+ I/O USB Communication signal USB D+

4 GND I Ground

5 WL_HOST_WAKE O Wake On WLAN

6 VCC I Power Supply 3.3V

7 N.C - Not connected

8 GND I Ground

①⑧

S P E C I F I C A T I O N

Reg. Date : 2017.09.01 MODEL NAME: LGSWFAC81

Rev. No. : 1.0

8. Installation Manual

Install the module like below in the back of the TV

TV Real Panel

LGSBFAC81 installed position

Regulatory Notices

1. FCC

FCC Part 15.19 Statements:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

FCC Part 15.21 statement

Any changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate this equipment.

FCC Part 15.105 statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

OEM Responsibilities to comply with FCC and Industry Canada Regulations

The module has been certified for integration into products only by OEM integrators under the

following condition:

- The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is

maintained between the radiator (antenna) and all persons at all times.

- The transmitter module must not be co-located or operating in conjunction with any other antenna

or transmitter except in accordance with FCC multi-transmitter product procedures.

As long as the two condition above is met, further transmitter testing will not be required. However,

the OEM integrator is still responsible for testing their end-product for any additional compliance

requirements required with this module installed (for example, digital device emissions, PC

peripheral requirements, etc.).

End Product Labeling

The module is labeled with its own FCC ID and IC Certification Number. If the FCC ID and IC

Certification Number are not visible when the module is installed inside another device, then the

outside of the device into which the module is installed must also display a label referring to the

enclosed module. In that case, the final end product must be labeled in a visible area with the

following:

“Contains FCC ID: BEJLGSWFAC81

“Contains IC: 2703H-LGSWFAC81”

2. IC

RSS-GEN, Sec. 7.1.3 – (licence-exempt radio apparatus)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to

the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit

pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

RF Exposure

The antenna (or antennas) must be installed so as to maintain at all times a distance minimum

of at least 20 cm between the radiation source (antenna) and any individual. This device

may not be installed or used in conjunction with any other antenna or transmitter.

l'exposition aux RF

L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une

distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne

physique.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could

void your authority to operate thisequipment.Attention:

Les changements ou modifications de cet appareil non expressément approuvé par le fabricant

peuvent annuler votre droit à utiliser cet équipement.

Étiquetage du produit final (IC)

Le module BT111 est étiqueté avec sa propre identification FCC et son propre numéro de

certification IC. Si l’identification FCC et le numéro de certification IC ne sont pas visibles lorsque

le module est installé à l’intérieur d’un autre dispositif, la partie externe du dispositif dans lequel

le module est installé devra également présenter une étiquette faisant référence au module inclus.

Dans ce cas, le produit final devra être étiqueté sur une zone visible avec les informations

suivantes :

« Contient module émetteur identification FCC ID : BEJLGSWFAC81

« Contient module émetteur IC : 2703H-LGSWFAC81”

Tabla de contenidos

Otros manuales de Unidad de control de LG

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario