LG SD500 Manual

LG-SD500 Operator’s Guide

December 08, 1999

jong-gil Lee

FCC RF EXPOSURE INFORMATION

In August 1996 the Federal Communications Commission (FCC) of the United States

with its action in Report and Order FCC 96-326 adopted an updated safety standard for

human exposure to radio frequency (RF) electromagnetic energy emitted by FCC

regulated transmitters. Those guidelines are consistent with the safety standard

previously set by both U.S. and international standards bodies. The design of this

phone complies with the FCC guidelines and these international standards.

Use only the supplied or an approved antenna. Unauthorized antennas, modifications,

or attachments could impair call quality, damage the phone, or result in violation of

FCC regulations.

Do not use the phone with a damaged antenna. If a damaged antenna comes into

contact with the skin, a minor burn may result. Please contact your local dealer for

replacement antenna.

Body-worn Operation

This device was tested for typical body-worn operations with the back of the phone kept

0.79 inches (2 cm) from the body. To comply with FCC RF exposure requirements, a

minimum separation distance of 0.79 inches (2 cm) must be maintained between the

user’s body and the back of the phone, including the antenna, whether extended or

retracted. Third-party belt-clips, holsters and similar accessories containing metallic

components should not be used. Body-worn accessories that cannot maintain 0.79

inch (2 cm) separation distance between the user’s body and the back of the phone,

and have not been tested for typical body-worn operations may not comply with FCC

RF exposure limits and should be avoided.

Vehicle Mounted External Antenna (optional, if available.)

A minimum separation distance of 7.9 inches (20 cm) must be maintained between the

user/bystander and the vehicle mounted external antenna to satisfy FCC RF exposure

requirements.

For more information about RF exposure, please visit the FCC website at www.fcc.gov

WARNING! Read this information before using your phone

Terminal Development Center

LGIC

Call Status Functions

1.Memo (Memo Soft Key 2)

Function to store a telephone number while calling

lSelect Memo and enter the telephone number to store.

lPress Store (Soft Key 1) key. (Name is not stored)

2.Record While Calling (Menu Soft Key 1 + 1)

Function to record the conversation while calling

3. Send Own No. (Menu Soft Key 1+2)

When you leave behind your phone number when using a pager or voice mail, you can use

this function to simply send your own phone number without having to press each digit of

the number. Also, you can send, during a call (when using pager or voice mail), your phone

number to other parties.

4.MIC Volume Control (Menu Soft Key 1 + 3)

Function to control the sensitivity of MIC while calling

lYou can select ‘High’or ‘Low’

5.Volume Control (Side Keys)

Function to control the volume while calling

lYou can control the volume by pressing Side Keys.

6.Mute Feature (Clear key)

Function to mute the speech voice while calling

lIf you press CLR key, the speech tone is muted immediately.

If you want to deactivate this mute function, press CLR key again.

Terminal Development Center

LGIC

Stand-by Status Menu Set-up and Its Functions

PIM

1. PHONE BOOK (Cion Secretary) [Menu + 1]

Telephone Directory / Scheduler / Alarm / Call Reserve / World Time

1.1 Contact Secretary [Menu +1 + 1 ]

1.1.1NEW ENTRY (Telephone Directory Register) [Menu +1+1+ 1 ]

1.1.2FIND ENTRY (Telephone Directory Search) [Menu +1+1+ 2 ]

1.1.3DELETE ENTRY (Telephone Directory Delete) [Menu +1+1+ 3 ]

-See the manual on the telephone directory function.

1.2 Calendar (Schedule Management Secretary) [Menu +1 + 2 ]

- See the manual on the diary function

1.2.1Calendar : You can search the calendar by entering the month and year you want to find.

Menu +1 +2 + Menu +1

1.2.2ADD NEW

Menu +1 +2 + Menu +2

1.2.3SEARCH : Used to check if there is schedule,memo,anniversary on the date for your search

Menu +1 +2 +Menu +3

1.2.4 DELETE ALL : Used to delete the schedule saved in the phone.

Menu +1 +2 +Menu +4

1.2.5 DELETE OLD : Used to delete old records which are now unnecessary because their dates have

expired

Menu +1 +2 +Menu +5

1.3 Alarm Secretary [Menu +1 + 3 ]

Alarm Time

*User can set an alarm to the desired time.

lSelect one of ‘Release / Once / Daily’.

lIf you select ‘Release’, it becomes the state of stand-by. In case an alarm time was set previously,

that setting time will be deleted.

lWhen ‘Once / Daily’is selected, you just enter the alarm time in the order of hour and minute.

lIn case the alarm time has been set already, the set alarm time and the soft keys of EDIT/OK are

displayed.

- If you select EDIT here, the soft key 1 of EDIT is displayed in ‘AM’or ‘PM”mode for editing the

input.

Terminal Development Center3

LGIC

l‘AM’and ‘PM’mode can be switched with Soft Key1[AM/PM]

lYou can edit the entered contents using DEL key.

lPress OK key to store the entered alarm time.

Note: The alarm bell is triggered at the set alarm time with the message of “Alarming Now”

displayed on the display.

Note: In case ‘Once’is selected, if the END key is pressed or 1minute is passed, the alarm time is

deleted.

1.4 Call Reservation Secretary [Menu + 1 + 4 ]

Call Reserve

*Function to originate a call to the reserved number automatically at the reserved time.

lEnter the reservation time in the order of “Hour :Minute”.

l‘AM’and ’PM’mode can be switched with Soft Key 1[AM/PM].

lPress OK key to store the entered reserved call time.

lEnter the reservation telephone number.[Up to 32 characters acceptable]

lStore the entered telephone number using STORE key.

Note: Telephone rings at the reserved time with the message of “Time for Reserved Call”on the

display.

Note:If the END key is pressed or one minute is passed, the reserved call time is automatically

deleted and stored in the last call list.

1.5 World Time Secretary [Menu +1 + 5]

World Time

*Function to confirm the standard time of major cities in the world based on GPC time.

This function is available in CDMA mode only.

lSelect the city you want to check using ‘Soft Key1’or ‘V/#’key and press OK key.

Then, the international standard time of the selected city is appeared.

Cities applicable

Guam / New York / Dacca / Dallas / Denver / Delhi / Tokyo / Detroit / London / Rome / Los Angeles /

Lisbon / Riode Janeiro / Manila / Madrid / Mexico / Moscow / Montreal / Bangkok / Berlin / Beijing /

Beirut / Boston / Buenos Aires / Vienna / Sydney / Seattle / Chicago / Singapore / Athens / Abu Dhabi /

Ajoles / Amsterdam / Anchorage / Oakland / Washington / Jakarta / Jedda / Kabul / Cairo / Caracas /

Colombo / Kuwait / Taipei / Tehran / Paris / Hanoi / Helshinki / Honolulu / Hongkong

Terminal Development Center

LGIC

2.Volume Control [Menu + 2]

Function to control Ring /Key Tone /Call Volume

2.1 Ringer Volume (Receiver Volume Control) [Menu +2 +1]

lSelect the volume using the next setup key (Soft Key 1).

lSelect the volume you want using V/#keys.

lStore the selected volume using the selection key.

2.2 Key Tone Volume Control [Menu +2 +2]

lSelect the volume using the next setup key (Soft Key 1).

lSelect the volume you want using V/#key.

lStore the selected volume using the selection key.

2.3 Earpiece Volume Control [Menu +2 +3]

lSelect the volume using the next setup key (Soft Key 1).

lSelect the volume you want using V/#key.

lStore the selected volume using the selection key.

3. Select Ring (Bell Selection) [Menu +3 ]

Function to select the bell type for the incoming call.

3.1 Types of Bell [Ring / Vibration / Vibration + Ring]

lSelect Menu + 3+ 1.

lSelect the bell type using the next setup key (Soft Key 1).

lSelect the type of bell you want using V/#key.

lStore the selected status using the selection key.

3.2 Bell Selection (17 types)

[General / Sound of glass bead / Kung-tha-ri Shabara / Rise tone / Alarm tone / Chime bell / Code

tone / Tune of Japanese apricot tree / Pathetic sonata / Bolero of love/ Tune of bird / Father’s

face / Small fountain / Edelweiss / A happy home / Nostalgia / Mail carriage]

lSelect Menu + 3+ 2

lSelect the type of bell using the next setup key (Soft Key 1).

lSelect the bell you want using V/#key.

lStore the selected status using the selection key.

Terminal Development Center

LGIC

4. Call Time [Menu + 4]

Function to verify the record on the call time

4.1 Last Call Time

*Function to show the last call time

lSelect Menu + 4+ 1.

lPress OK key to return to the stand-by state.

4.2 Total Call Time

*Function to show the number of call and the call time for all calls of receiving and transmitting.

User can verify the total number of calls made and the call time through this function.

lSelect Menu + 4+ 2.

lIf you select OK key (Soft Key2), it returns to the stand-by status and if you select DEL key (Soft

Key1), you can delete the accumulated total call time.

4.3Home call + Roam calls

*Used to display the call time for calls only within your business place.

*Used to display the call time of calls with other business enterprise places.

lSelect Menu + 4+ 3.

5. Secret Function [Menu + 5 + Password 4-digit]

Lock mode setup / Call list delete / Private information delete / Voice list delete /

Emergency phone number store / Password change / International call restrict /

Automatic PIN transmit / Software version confirm functions can be performed in this menu.

5.1. Lock Mode

*Function to restrict the originating and storing functions.

*You can select ‘Release / Power-On / Always’

lPress Menu + 5+ Password 4-digit + 1

lSelect one of ‘Release / Power-On / Always’using ‘Soft Key1’or ‘V/#’key and press the store

key.

lIf you select ‘Always’, the phone falls in the lock mode always, and [Select] menu and the calling

are locked.

-If you try to call in this case, you are prompted for the password and if the entered password is

identified, the call is established. In the lock mode, if you press [Locking Release] button, the

Terminal Development Center6

LGIC

locking on the [Select] key is released and the [Locking Release] button is changed to [Select]

button.

-Even in this case, whenever you try to call, the password is required.

-If you want the locking release, you should release this setup from the [Menu].

lIf you select ‘Power-On’, the locking function is not immediately executed but when the phone is

switched on, it is automatically set to the lock mode and at the same time, the soft key is changed

to [Menu], [Locking Release].

Default password is ‘0000’.

5.2. Call List Delete

*Function to delete all the telephone numbers stored in the last call list.

lSelect Menu + 5 + Password 4-digit + 2

lSelect ‘Yes’from Yes/No using the next setup key (Soft Key1) or ‘V/#’key and press the

SELECT key.

5.3. Private Information Delete

*Function to delete all the contents stored in the memory address 01 ~ 200.

lSelect Menu + 5 + Password 4-digit + 3.

lSelect ‘Yes’from Yes/No using the next setup key (Soft Key1) or ‘V/#’key and press the

SELECT key.

During the deletion, a message of ‘Please, wait’appears and after the completion of the deletion

it returns to the stand-by status.

5.4 Voice List Delete

*Function to delete all the voice items (20 entities) from the memory addresses where voice is

stored of memory address 01 ~ 200.

lSelect Menu +5+ Password 4-digit + 4.

lSelect ‘Yes’from Yes/No using the next setup key (Soft Key1) or ‘V/#’key and press the

STORE key.

5.5. Emergency Phone Number Store

*Function used to enter the emergency telephone number [Up to 3 numbers ]

lSelect Menu + 5 + Password 4-digit + 5.

If the telephone number stored in the telephone number 1is appeared empty, a message of

Terminal Development Center7

LGIC

‘None’appears.

lSelect the memory address where you want to make input using the next setup key (Soft Key1) or

‘V/#’key [ 1 ~ 3 ]

lSelect the edit mode by pressing EDIT key.

lEnter the telephone to store and press OK key.

If you want to terminate the process at this time, press the END key and if you want to enter the

telephone in other memory address, repeat the procedures that follow the step of memory address

selection.

5.6.Password Change

*Function to change the password

lSelect Menu + 5 + Password 4-digit + 6.

lEnter a new password of 4-digit and press STORE key.

lFor the reconfirmation, enter the password you entered just before in 4-digit.

lPress OK key. [It is then back to the previous status]

5.7. International Call Restrict

*Function to restrict the originating for the international call

lSelect Menu + 5 + Password 4-digit + 7

lSelect ‘Setup’of ‘Setup/Release’using the next setup key (Soft Key1) or ‘V/#’key and press

STORE key.

Once the international call is restricted, the international call cannot be originated.

5.8. Automatic PIN Transmit

*Function to set up PIN CODE and store it.

lSelect ‘Setup’of ‘Setup/Release’using the next setup key (Soft Key1) or ‘V/#’key and press

STORE key.

lSelect Menu + 5 + Password 4-digit + 8

This function is not used currently. (It is subject to change later by the service provider)

5.9. Software Version Confirm

*Function to confirm the software version of the phone.

lSelect Menu + 5 + Password 4-digit + 9.

¢ÑMSM Version / Self Source Version / Qualcomm Source Version are appeared.

Terminal Development Center8

LGIC

6. Convenient Functions [ Menu + 6 ]

Area code input/setup, automatic reception, calculator, voice recognition setup, automatic

answer functions can be set.

6.1 Automatic Area Code

*The stored area code is added to the dial number automatically while a call is originated.

lSelect Menu + 6+ 1.

lSelect one of ‘Setup/Release’using the next setup key (Soft Key1) or ‘V/#’key and press

STORE key.

lIf you select ‘Release’, it will be in the stand-by state. In case there is a pre-stored number, that

number will be deleted.

lPress SETUP to enter the area code. [Max. up to 4digits ]

lPress OK key to store the entered contents.

If the entered area code is not registered one, a message of ‘Wrong Number’appears with a

beep alarm and it returns to its initial stage.

¢Ã

World Area Code (Skip)

6.2Automatic Reception

*If the user does not answer an incoming call, after the telephone rings as many times as the set

number of the bell for the automatic reception, call is established automatically.

lSelect Menu + 6+ 3

lSelect one of ‘Release / After 1st Ring / After 3rd Ring’using the next setup key (Soft Key1) or

‘V/#’key and press STORE key.

In case of melody, the incoming call is received after the 1 st tune regardless of the setting

value.

6.3Calculator

*[Add / Subtract / Multiply / Divide] can be executed.

*You can enter the decimal point with [ V] key.

lSelect Menu + 6+ 4.

lEnter numbers. [9 digits can be entered including the decimal point]

lSelect operators using Soft Key1 key.

lEnter numbers. [9 digits can be entered including the decimal point]

Tabla de contenidos

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario

Blackbe;rry

Blackbe;rry CURVE 8300 - SMARTPHONE Manual de usuario

Blackbe;rry

Blackbe;rry 8707 - VERSION 4.1 Manual de usuario