Lexmark E120 Manual de usuario
Quick Reference
1
Quick Reference
Understanding the Operator Panel
The printer operator panel has two buttons and two lights. Lights indicate the status of the printer.
Buttons are used to continue or cancel the current print job.
When the printer is turned on, both lights cycle as a self test is performed. Also, when the printer is
reset, or when a printer setting is changed in the menus, both lights cycle.
•Press and release Continue to resume printing.
•Press and release Continue twice quickly to display the secondary light sequence.
•Press Continue from the Ready state to print the menu settings page.
•Press and hold Cancel to cancel the current job.
•Press and hold Cancel until both lights come on to reset the printer.
Understanding the operator panel lights
The operator panel lights mean different things, depending on their sequence. Lights that are off, on,
and/or blinking indicate printer conditions such as printer status, intervention, or service.
Use the light sequence table to find the message being indicated, then click the message for more
information.
Ready / Data
Cancel
Continue
Error
Understanding the Operator Panel
2
Light sequence
Primary
light
sequence
Secondary
light
sequence
Message
Ready / Data
Error
Ready / Data
Error
Ready / Power Saver
Busy
Waiting
Cancel job / Reset printer
Flushing buffer
Invalid engine code (Ready / Data light blinks once)
Not ready (Ready / Data light blinks once)
Printing font list or menu settings page
Programming engine code or system code
Restoring factory defaults
Cartridge region mismatch (Ready / Data light blinks four times)
Change cartridge / Defective cartridge (Ready / Data light blinks three times)
Open door (Ready / Data light blinks once)
Complex page (Ready / Data light blinks three times)
ENA connection lost (Ready / Data light blinks five times)
Insufficient collation area (Ready / Data light blinks three times)
Load media (Ready / Data light blinks once)
Print side two of a duplex job (Ready / Data light blinks once)
Ready / Data light on =
Ready / Data light blinking =
Error light on =
Error light blinking =
Printing the menu settings and network setup page
3
Printing the menu settings and network setup page
To print the menu settings and network setup pages, press from the Ready state. The printer
automatically prints the menu settings and network setup pages.
A list of the printer settings and the current default values are printed on the menu settings page. The
current default settings are marked with an asterisk. The network setup page confirms the network
Status is “Connected” and lists the current network settings.
Restoring factory defaults
This function will return most of the settings back to their factory values. The display language and
the settings in the Network and USB menus are not returned to the factory defaults.
To restore the printer to the original factory defaults, press and hold for more than three
seconds.
Note: Before restoring the factory defaults, make sure the host computer or network has
stopped sending information to the printer.
Memory full (Ready / Data light blinks three times)
Host interface disabled (Ready / Data light blinks five times)
Jam in the printer paper path (Ready / Data light blinks ten times)
Jam in Tray 1 / priority feeder (Ready / Data light blinks four times)
Short paper (Ready / Data light blinks three times)
Toner low (Ready / Data light blinks eight times)
Replace long-life photoconductor kit (Ready / Data light blinks once)
Service error (Ready / Data light blinks ten times)
Primary
light
sequence
Secondary
light
sequence
Message
Ready / Data
Error
Ready / Data
Error
Loading paper or other print media
4
Loading paper or other print media
To help prevent jams:
•Prepare print media for loading by flexing or fanning it back and forth. Straighten the edges
on a level surface.
•Do not overload the paper trays.
•Never mix media types within a tray.
Source Sizes Types
Capacity*
(sheets)
Tray 1 A4, A5, JIS-B5, letter, legal, executive, folio,
statement, universal†
Plain paper,
bond paper,
transparency,
label
150 sheets
5 transparencies
5 labels
3 x 5 inch, other Card stock 5 cards
7¾, 9, 10, DL, C5, B5, other Envelope 5 envelopes
Priority feeder A4, A5, JIS-B5, letter, legal, executive, folio,
statement, universal†
Plain paper,
bond paper,
transparency,
label
15 sheets
5 transparencies
5 labels
A6 Plain paper,
bond paper
30 sheets
3 x 5 inch, other Card stock 5 cards
7¾, 9, 10, DL, C5, B5, other Envelopes 3 envelopes
* Capacity for 20 lb print media, unless otherwise noted.
†Universal size ranges:
– Tray 1: 76–216 x 190–356 mm (3.0–8.5 x 7.5–14.0 in.) (includes 3 x 5 in. cards)
– Priority feeder: 76–216 x 190–356 mm (3.0–8.5 x 7.5–14.0 in.) (includes 3 x 5 in. cards)
Loading paper or other print media
5
Loading Tray 1
1Open the paper cover by lifting up until the cover clicks into a fully open position.
2Adjust the slide and attached backstop to the length of the selected print media.
Note: To decrease width, push in on the left guide. To increase width, squeeze the tab
attached to the right guide, and slide it to the right.
Loading paper or other print media
6
3Place the prepared print media into the tray, and lightly adjust all guides against the loaded
print media edges.
Note: Load letterhead paper with the design side facing up and the top edge of the sheet
feeding into the printer first. Load envelopes with the flap side down and the return
address first. The stamp area will feed through last.
4Close the paper cover.
Canceling a print job
7
Loading print media into the priority feeder
The priority feeder can be used to make quick runs of print media types or sizes not currently loaded
in Tray 1.
1Adjust the guides to the width of the print media.
2Place the selected print media, with the side to be printed faceup, at the center of the priority
feeder. The print media rests on the Tray 1 paper cover.
3Push the selected print media into the printer until the print media stops.
Note: Do not force print media into the feeder. Forcing print media causes jams.
Canceling a print job
A print job can be canceled from the operator panel or from the computer. The Cancel job light
sequence appears on the operator panel when a job is canceled (see “Cancel Job/Reset printer” on
page 30 of your User’s Guide).
From printer operator panel
Press and release to cancel the current print job. Press and hold for more than three
seconds to reset the printer.
Canceling a print job
8
From a Windows computer
1Click Start ÆSettings ÆPrinters.
2Double-click the printer being used to print the current job.
A list of print jobs appears.
3Right-click the current document, and then click Cancel.
From a Macintosh computer
When a job is sent to print, the printer icon appears on the desktop.
1Click Applications.
2Click Utilities.
3Double-click Printer Setup Utility.
A list of print jobs appears.
4Double-click the printer name to see a list of print jobs.
5Click the print job you wish to cancel.
6From the tool bar, click Delete.
Clearing jams
9
Clearing jams
When a jam occurs, the printer stops, and the Error light on the operator panel blinks. To determine
the location of the jam, view the secondary light sequences. Prepare the printer for jam removal by
opening the paper support and removing all printed pages from the output bin. Then, follow these
steps to clear the entire paper path.
1Open the rear door by sliding the door release button to the right.
2Remove any lodged print media from the paper path.
Warning: When the rear door is open, be careful not to touch the attached roller. Touching
the roller can cause contamination and affect print quality. Do not leave the rear
door open for an extended amount of time. Exposure to light will damage the blue
drum of the long-life photoconductor kit and affect print quality.
Clearing jams
10
3Open the top door, and remove any lodged print media from the paper path.
CAUTION: The fuser may be hot. To avoid personal injury, use caution when opening the top
door to remove a jam from the fuser area.
4Open the front door by sliding the release button to the left.
Otros manuales para E120
4
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Impresora de Lexmark
Lexmark
Lexmark 350 Manual
Lexmark
Lexmark C925 Manual de usuario
Lexmark
Lexmark 632n - T B/W Laser Printer Manual de usuario
Lexmark
Lexmark MX810 Series Manual de usuario
Lexmark
Lexmark MX826ade Manual de usuario
Lexmark
Lexmark C792 Family Manual de usuario
Lexmark
Lexmark C925de Manual de usuario
Lexmark
Lexmark 25C0010 - X 500n Color Laser Manual de usuario
Lexmark
Lexmark Z51 Color Jetprinter Manual de usuario
Lexmark
Lexmark E320 Manual de usuario
Lexmark
Lexmark 22W0000 - P 350 Color Inkjet Printer Manual de usuario
Lexmark
Lexmark C 750 Guía de inicio rápido
Lexmark
Lexmark X748dte Manual de usuario
Lexmark
Lexmark MS710 Series Guía de referencia rápida
Lexmark
Lexmark C3426 Manual de usuario
Lexmark
Lexmark E260d Series Manual de usuario
Lexmark
Lexmark XM1140 Manual de usuario
Lexmark
Lexmark C746 Manual de usuario
Lexmark
Lexmark C792e Manual de usuario
Lexmark
Lexmark C 752 Manual de usuario
