Leviton A8810-41M Manual de usuario

DI-000-A8810-00A

Energy Management Hub and 3-Phase Meter

EMX Data Acquisition System

Cat. No. A8810-41M/41R

Installation Guide

TABLE OF CONTENTS

Warnings ..............................................................................................................................................1

Cautions ...............................................................................................................................................1

1 Getting Started ..................................................................................................................................2

2 Site Location and Providing Power ...............................................................................................4

3 Internal Component Conﬁguration and Operation .......................................................................7

4 Final Steps .....................................................................................................................................11

5 Standard Statements .....................................................................................................................15

WARNINGS:

• TO AVOID FIRE, SHOCK OR DEATH, turn off all power supplying equipment before working on or

inside the equipment. Use a properly rated voltage sensing device to conﬁrm power is off.

• RISK OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH. CAREFULLY READ AND FOLLOW

INSTRUCTIONS:

• This equipment MUST be installed and serviced by qualiﬁed electrical personnel with the requisite

knowledge, training and experience related to the installation and operation of this equipment.

• Follow safe electrical work practices. See NFPA 70E in the USA, or applicable local codes.

• Product may use multiple voltage/power sources. Be sure all sources of power have been disconnected

before servicing.

• Do not depend on this product for voltage indication.

• Only install this product on insulated conductors.

CAUTIONS:

• This product is not intended for life or safety applications.

• Do not install this product in hazardous or classiﬁed locations.

• The installer is responsible for conformance to all applicable codes.

• Mount this product inside a suitable ﬁre and electrical enclosure.

• If the collector is connected directly to a source of voltage, the pulse isolator will immediately burn out

and become non-responsive.

WARNINGS AND CAUTIONS

1 GETTING STARTED

1.1 Recommended Installation Hardware

Not all installations will be the same, but in general we recommend that you have the

following available:

• Power Drill

• Large Phillips Head – Number 2

• Small Flathead 2.5mm or 1/8”

• Laptop – Windows PC with Ethernet Port

• Cable Glands and Weatherproof Sealant

• Digital Multimeter

• CAT 5 Cable

• Belden™1120A Twisted Shielded Pair wire

• Wire Strippers

• Mounting Screws (4)

1.2 Packing List

The following Items are included with the panel:

• Enclosure Mounting Tabs

• Short Ethernet Patch Cable

• Ethernet Cable 7’

• Calibration Certiﬁcates, Operating Manuals, Engineering Drawings, and Wiring

Diagrams are located on the inside of the enclosure door.

• This enclosure is packed for protection during transit. Please inspect all materials

upon receipt to ensure no damage has occurred in transit. Please report any

damage to your product to your vendor immediately. Packing material must

be removed for operation. Please discard, recycle, or reuse these materials

appropriately.

Technical Support

For technical support, contact Leviton at 800-959-6004, or via email at

[email protected]

1 GETTING STARTED

1.3 Product Overview

The EMX panel comes fully assembled, wired and ready for installation.

Neutral and Ground

input terminals

Power Meter –

Series 4100

Bi-Directional

(4DUMR split core

or Rogowski coil

versions)

Energy Monitoring

Hub - A8810

Power Supply

– Phoenix

Contact Step-PS

277AC/24DC/3.5A

Separate 3-Phase

(meter reference

voltage) and Single-

Phase (system

power) fused AC

power input terminals

Current Transformer

input terminals

2 SITE LOCATION AND PROVIDING POWER

2.1 Mounting the Enclosure

2.1.1 Mount the enclosure in a location according to and compliant with local

electric code.

2.1.2 Mounting Tabs and screws are provided with the enclosure. The provided

screws are intended to be used to mount the tabs to the enclosure. User to

provide additional mounting hardware as needed.

2.1.3 Create knockout holes for any necessary power, current transformer and

communications lines in the bottom of the enclosure.

2.1.3.1 To maintain the warranty and integrity of the panel, all holes/punch

outs for conduit and wires should only be drilled in the bottom of the

enclosure and properly sealed to prevent exposure to moisture.

2.1.3.2 To prevent interference, it is recommended that sense voltage and CT

wiring are separated and run through different knock outs.

2.1.4 The enclosure does have the ability to be padlocked externally. This is

recommended to maintain security and device integrity.

2 SITE LOCATION AND PROVIDING POWER

2.2 Connecting Input Power

2.2.1 Per local electrical code and site speciﬁcations connect power to voltage

sense input and panel power input.

2.2.2 There are separate power inputs for meter reference voltage and panel power

to allow the hub and meter to remain powered if the circuits being monitored

need to be off.

2.3 Connecting Current Transformers

2.3.1 CT inputs are located next to the power input section on the lower DIN rail.

2.3.2 CT should be wired per manufacturer directions indicated below. CT terminals

are clearly labeled CT1 (X1/X2), CT2 (X1/X2), and CT3 (X1/X2).

2 SITE LOCATION AND PROVIDING POWER

2.4 Observe correct CT orientation

X1 White

X2 A

X2 B

X2 C

Black

X1 White

X2 A

X2 B

X2 C

Black

L1N

X1 White

X2 A

X2 B

X2 C

Black

White

Black

X2 X1

L2L1

X1 White

X2 A

X2 B

X2 C

Black

White

Black

X2 X1

X2 White

Black

L2L1N

X1 White

X2 A

X2 B

X2 C

Black

White

Black

X2 X1

X2 White

Black

L2L1N

X1 White

X2 A

X2 B

X2 C

Black

White

Black

X2 X1

X2 White

Black

Diagram 1: 1-Phase Line-to-Neutral

2-Wire System 1CT

Diagram 2: 1-Phase Line-to-Line

2-Wire System 1CT

Diagram 3: 1-Phase Direct Voltage

Connection 2CT

Diagram 4: 3-Phase 3-Wire 3 CT no PT

Diagram 5: 3-Phase 4-Wire Wye Direct

Voltage Input Connection 3 CT

Diagram 6: 3-Phase 4-Wire Wye

Connection 3CT 3 PT

Use System Type 10 (1L + 1n) Use System Type 11 (2L)

Use System Type 12 (2L + 1n) Use System Type 31 (3L)

Use System Type 40 (3L + 1n) Use System Type 40 (3L + 1n)

3 INTERNAL COMPONENT CONFIGURATION AND OPERATION

3.1 Introduction

The Leviton EMX comes with multiple internal components that are essential to operation.

The following describes these components and outlines basic installation instructions.

3.2 Phoenix Contact Power Supply

Description: The Phoenix Power Supply provides DC power to the components within

the cabinet, and, if needed, external devices that you may wish to power. There are no

installation steps required, however the following are some product details.

3.2.1 Model Number: STEP-PS/277AC/24DC/3.5 - 2904945

3.2.2 Nominal Input Voltage Range: 100 VAC – 277 VAC

3.2.3 Nominal Output Voltage: 24 VDC

3.2.4 Nominal Output Current: 3.5A

3.3 Leviton 4DUMR Power Meter

Description: The Leviton 4DUMR is a revenue grade, bi-directional, power meter that

provides information about the electrical performance of the monitored circuit.

Conﬁguration of the meter assumes that the meter has arrived with factory default

settings. In the steps below you will: Set up communication parameters, voltage and

current information, and system information. All of this can be done with the push buttons

on the meter.

Important: Note now whether you have Split Core or Rogowski “Rope” CT as it will

alter the steps that follow.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cambiar de Leviton

Leviton

Leviton Z-MAX ZMDSW-S1W Manual de usuario

Leviton

Leviton 47611-5GB Instrucciones de instalación

Leviton

Leviton Scene Capable Electronic Switch Manual de usuario

Leviton

Leviton VSHUB Manual de usuario

Leviton

Leviton Powerswitch MDS30-AX Manual de usuario

Leviton

Leviton Decora IPV0R Manual de usuario

Leviton

Leviton PK-A3419-10-00-5A Manual de usuario

Leviton

Leviton Vizia-RF Instrucciones de instalación

Leviton

Leviton Lumina RF 10A Manual de usuario

Leviton

Leviton SS0AV-091 Manual de usuario

Leviton

Leviton OMNI-BUS Instrucciones de montaje

Leviton

Leviton PowerSwitch DS30-FAX Manual de usuario

Leviton

Leviton 47691-5MS Manual de usuario

Leviton

Leviton 1461 Manual de usuario

Leviton

Leviton 321 Manual de usuario

Leviton

Leviton DECORA VPT24 Instrucciones de funcionamiento

Leviton

Leviton 35A00-1 Instrucciones de montaje

Leviton

Leviton HCS08 Manual de usuario

Leviton

Leviton 1080 Manual de instrucciones

Leviton

Leviton Decora IPS02 Manual de usuario

Leviton

Leviton Acenti AC201-1L Manual de usuario

Leviton

Leviton Decora Plus 5624 Manual de usuario

Leviton

Leviton Decora Smart DG3HL Manual de usuario

Leviton

Leviton 37A00-1 Instrucciones de montaje

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario