LevelOne GEU-0822 Manual de usuario

GEU-0822

8-Port Gigabit Switch

V1. 2_20151223

1. INTRODUCTION......................................................... 3

1.1 Product Briefs ....................................................................................................3

1.2 Product Features.................................................................................................3

1.3 Hardware Introduction.......................................................................................4

2. CONNECTING THE SWITCH.................................... 5

2.1 Package Contents...............................................................................................5

2.2 Before You Connect to the Network..................................................................5

3. Connecting the switch................................................... 6

4. Appendix....................................................................... 7

4.1 Technical Specifications ....................................................................................7

4.2 RJ-45 PIN SPECIFICATION ............................................................................8

1. INTRODUCTION

1.1 Product Briefs

The switch is a un-management layer 2 10/100/1000Mbps switch; it provide dedicated 10,

100 or 1000 Mbps Ethernet bandwidth on each port. The ports will automatically detect the

speed, duplex and MDI/MDIX status of the device it is connecting to, and adjust these

settings accordingly. The Switch ports can be used to network computers, printers, servers,

routers, other switches or any device equipped with an Ethernet port. For best performance,

use Category 5 or better Ethernet cabling.

This stand-alone Switch is very easy to set up, there is no network management required.

Just power on the Switch and connect the cables. Keep in mind however that the standard

rules of Ethernet regarding cable length apply to this and all Ethernet devices. The length of

an Ethernet cable from one device to another cannot exceed 100 meters (or 300 feet).

1.2 Product Features

The Switches do not require any management. All Switches are designed for easy

installation, flexibility and high performance. Connect devices to the Switch as the scale and

volume of network traffic increases.

8 10/100/1000Mbps Ethernet ports

Auto-Negotiation for 10/100/1000Mbps and duplex mode

Auto-MDI/MDIX for each port

Supports Full/Half-duplex transfer mode for 10 and 100Mbps

Supports Full-duplex transfer mode for 1000Mbps

Full wire speed reception and transmission

Store-and-Forward Switching method

Supports 8K absolute MAC addresses

Switch Supports embedded SRAM for data buffering

IEEE 802.3x flow control for Full-duplex

Back pressure flow control for Half-duplex

Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure,

format, and support for CSMA/CD protocol, full duplex, flow control, and management

objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet

and a hundredfold increase over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps

and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade

without wasting a company’s existing investment in hardware, software and trained

personnel.

The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping

with the network bottlenecks that frequently develop as computers and their bus speeds get

faster and more users use applications that generate more traffic. Upgrading key components,

such as your backbone and servers to Gigabit Ethernet can greatly improve network response

times as well as significantly speed up the traffic between your subnets.

1.3 Hardware Introduction

1.3.1 Product Appearance

1．Front Panel

The figure below shows the front panel of the Switch.

8-port Gigabit Switch Steel Front Panel

The fisrt LED is Power Indicator and other five LEDs are Status Indicator.Details will be

described in the next chapter See the chapter 1.3.2

2．Rear Panel

The figure below shows the rear panel of the Switch, Including All MDI/MDI-X ports

8-port Switch Steel Rear Panel

Auto MDI/MDI-X Ports:

All ports support automatic MDI/MDI-X crossover detection. The AutoMDI/MDI-X

function makes it simple to connect to the switch—just plug either a Crossover or

Straight-Through CAT5 cable into any port.

1.3.2LED Indicators

Table 1-3 Gigabit Ethernet Switch LED Indicators

LED

Panel

signature

Status

Description

Power

Indicator

Power

Green ON

Switch is powered ON

OFF

Switch is powered OFF

Status

Indicator

Link/Act

Green ON

Link

Green Blinking

Activity

OFF

No link path

Status

Indicator

1000M

Green ON

1000Mbps Link

OFF

10/100Mbps Link OR OFF

2. CONNECTING THE SWITCH

2.1 Package Contents

Open the shipping carton of the Switch and carefully unpack its contents.

The carton should contain the following items:

One 8 Port 10/100/1000BASE-T Gigabit Ethernet Switch

Power Adapter

CD-ROM with Manual and QIG

Quick Installation Guide

If any item is found missing or damaged, please contact your local reseller for replacement.

2.2 Before You Connect to the Network

The site where you install the Switch may greatly affect its performance. Please follow

these guidelines for setting up the Switch.

Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs) of

weight. Do not place heavy objects on the Switch.

The power outlet should be within 1.82 meters (6 feet) of the Switch.

Visually inspect the power cord and see that it is fully secured to the AC power port.

Make sure that there is adequate space for proper heat dissipation from and adequate

ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and

rear of the Switch for ventilation.

Install the Switch in a fairly cool and dry place for the acceptable temperature and

humidity operating ranges.

Install the Switch in a site free from strong electromagnetic field generators (such as

motors), vibration, dust, and direct exposure to sunlight.

When installing the Switch on a level surface, attach the rubber feet to the bottom of the

device. The rubber feet cushion the Switch, protect the casing from scratches and prevent

it from scratching other surfaces.

3. Connecting the switch

Cable Quality

For all connections to the Switch, use these rules to determine the Cable quality.

For connections to 10BASE-T and 100BASE-TX devices, use Category 5 or 5e

UTP/STP cable.

For connections to 1000BASE-T and 100BASE-TX devices, use Category 5e or better

UTP/STP cable.All 1000BASE-T connections operate in full duplex mode.

PC to Switch

A computer can be connected to the 8-Port 10/100/1000Mbps Switch via a two-pair

Category 3, 4, 5 UTP/STP Straight-Through or Crossover cable. A computer equipped with a

RJ-45 10/100/1000Mbps port can be connected to any of the five 8-Port 10/100/1000Mbps

Switch ports.

The LED indicators for the PC connection depend on the capability of the computer’s

Ethernet card. If the LED indicators are not lit after making a proper connection, check the

computer’s Ethernet card, the cable, and the 8-Port 10/100/1000Mbps Switch’s conditions

and connections.

Hub to Switch

A hub can be connected to the 8-Port 10/100/1000Mbps Switch via a two-pair Category 3,

4, or 5 UTP/STP Straight-Through or Crossover cable. For 1000Mbps operation a Category 5

cable must be used. The connection is accomplished from any port of the hub to any port of

the 8-Port 10/100/1000 Mbps Switch.

Switch to other devices

NOTE: UTP (Unshielded Twisted Pair) Ethernet cabling is adequate for

most small office environments. More expensive STP (Shielded Twisted

Pair) can also be used, but is generally only needed where there will be

risk of strong Electromagnetic of Radio Frequency Interference.

The 8-Port 10/100/1000Mbps Switch can be connected to another switch or other devices

(routers, bridges, etc.) via a two-pair Category 3, 4, 5 UTP/STP Straight-Through or

Crossover cable. A Category 5 cable must be used for 1000Mbps operation. The connection

can be accomplished from any port on the 8-Port 10/100/1000Mbps Switch to any of the

10Mbps ,100Mbps or 1000Mbps ports on another switch or other devices.

Port Speed & Duplex Mode

After plugging the selected cable to a specific port, the system uses auto-negotiation to

determine the transmission mode, auto-detecting the network speed for any new twisted-pair

connection.

If the attached device does not support auto-negotiation or has auto-negotiation disabled,

an auto-sensing process is initiated to select the speed and half-duplex mode is selected.

4. Appendix

4.1 Technical Specifications

Table 4-1 Gigabit Ethernet Switch General Features

Specification

Standards

IEEE 802.3 10BaseT

IEEE 802.3u 100BaseTX

IEEE 802.3ab 1000BaseT

IEEE 802.3x Flow Control

Features

RJ-45 Ports: 8

MAC Address: 8K

Buffer Memory: 128KB

Jumbo Frames: 9K

Transmission Method: Store and Forward

Filtering/Forwarding

Rates

1000Mbps port –1,488,000pps

100Mbps port - 148,800pps

10Mbps port - 14,880pps

Transmission Media

10BaseT Cat. 3, 4, 5 UTP/STP

100BaseTX Cat. 5 UTP/STP

1000BaseT Cat. 5E UTP/STP

Led Indicators

Per Port: Link/Act

Per Port:1000Mbps Link

Per Unit: Power

Power Requirement

9V/1A

Power Consumption

< 5 Watts

Dimensions

137mm×75mm×25mm(L x W x H)

Weight

<=0.5 kg

Operating Temperature

0℃to 40℃

Storage Temperature

-20℃to 70℃

Humidity

Operating:10 to 90% RH (non-condensing)

Storage: 5 to 95% RH (non-condensing)

4.2 RJ-45 PIN SPECIFICATION

The following diagram and tables show the standard RJ-45 receptacle/connector and their

pin assignments.

RJ-45 Connector pin assignment

Contact

Media Direct Interface Signal

TX_D1+

TX_D1-

RX_D2+

BI_D3+

BI_D3-

RX_D2-

BI_D4+

BI_D4-

Standard RJ-45 receptacle/connector

Otros manuales para GEU-0822

Tabla de contenidos

Otros manuales de Enrutador de red de LevelOne

LevelOne

LevelOne GEU-1621 Manual de usuario

LevelOne

LevelOne FBR-1406TX Manual de usuario

LevelOne

LevelOne FBR-1100TX Manual de usuario

LevelOne

LevelOne GEU-0822 Manual de usuario

LevelOne

LevelOne WBR-3406TX Manual de usuario

LevelOne

LevelOne FBR-1403TX Manual de usuario

LevelOne

LevelOne FBR-1461 Manual de usuario

LevelOne

LevelOne GEL-2461 Manual de usuario

LevelOne

LevelOne FSW-1650 Manual de usuario

LevelOne

LevelOne WBR-3405TX Manual de usuario

LevelOne

LevelOne FRT-2101TX Manual de usuario

LevelOne

LevelOne WBR-6802 Manual de usuario

LevelOne

LevelOne FSW-2411TX Manual de usuario

LevelOne

LevelOne WBR-3407 Manual de usuario

LevelOne

LevelOne WBR-6003 Manual de usuario

LevelOne

LevelOne FRT-2101TX Manual de usuario

LevelOne

LevelOne FEP-1611 Manual de usuario

LevelOne

LevelOne GSW-0507 Manual de usuario

LevelOne

LevelOne HomePlug Pro PLI-3210 Manual de usuario

LevelOne

LevelOne FSW-0508TX Manual de usuario

LevelOne

LevelOne WBR-6004 Manual de usuario

LevelOne

LevelOne FEP-0811 Manual de usuario

LevelOne

LevelOne WBR-6006 Manual de usuario

LevelOne

LevelOne FSW-0811 Manual de usuario

Manuales populares de Enrutador de red de otras marcas

Allnet

Allnet ALL0333AU Manual de usuario

HomeSeer

HomeSeer HT-SEL Manual de usuario

Sercomm

Sercomm Genesis OC3505D Manual de usuario

Billion

Billion BIPAC 5102 Series Manual de usuario

TP-Link

TP-Link TD-8817 Manual de usuario

Motorola

Motorola MR1900 Manual de usuario

Digi

Digi IX14 Manual de usuario

Cisco

Cisco NCS 540 Manual

XAVi

XAVi X8821e Manual de usuario

BEC

BEC 6200WZL Manual de usuario

MikroTik

MikroTik hAP ac3 Series Manual de usuario

Korenix

Korenix JetNet 5428G Series Manual de usuario

NETGEAR

NETGEAR FS526T - Switch Manual de usuario

Korenix

Korenix JetNet 5710G Series Manual de usuario

Automated Logic

Automated Logic ZN551 Manual del propietario

Cisco

Cisco ASR 1000 Series Manual del operador

EnGenius

EnGenius ESR-9710 Manual de usuario

Cisco

Cisco 805 Series Instrucciones de funcionamiento y seguridad