LevelOne IGC-0101 Manual de usuario

User Manual

IGC-0101

RJ45 to SFP Gigabit Industrial Media Converter, 1 PoE Output

FCC MARKING

This Equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to

radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at

his own expense.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not cause harmful interference, and

(2) this device must accept any interference received; including interference that

may cause undesired operation.

CE MARKING

This equipment complies with the requirements relating to electromagnetic

compatibility, EN 55022 class A for ITE, the essential protection requirement of

Council Directive 2004/108/EC on the approximation of the laws of the Member

States relating to electromagnetic compatibility.

Company has an on-going policy of upgrading its products and it may be possible

that information in this document is not up-to-date. Please check with your local

distributors for the latest information. No part of this document can be copied or

reproduced in any form without written consent from the company.

Trademarks:

All trade names and trademarks are the properties of their respective companies.

Key Features

➢Hardened Industrial graded Marvell IC

➢Rugged design Aluminum enclosure 103.5x32x81.5mm (LxWxD)

➢Supports 30Watts PSE on TX port

➢Supports SFP fiber speed 100M or 1000M dual mode

➢Surge protection diodes on power input.

➢ESD protection diodes on RJ-45 port

➢Provides increased Noise Immunity

➢Working in extreme environment -40°C to 75°C

Introduction

This IGC-0101 Industrial POE media converter is equipped with Hardened Marvell IC

to provide a reliable power source to power up your remote POE device. It is designed

for Security, Transportation and Telco application to extend your network distances.

With its multi-purpose design, it can also be used for Din-Rail or wall-mounted. It is

an ideal unit for IP surveillance, traffic monitoring and Security application in critical

environment. It can tolerate -40°C to 75°C in harsh environment to perform a

reliable network.

Installation package

The following items are shipped with this device:

Din-Rail Mounted * 1

Wall-Mounted * 2

Screws * 4

4 pin Terminal Block * 1

Power connection

This unit provides 4 pin terminal block. It can be operated using 48-56VDC power

source. Always Make sure your input voltage is within this supported voltage

range. You need to use 56VDC input to generate IEEE802.3at 30Watts power.

To make power connection – Follow the printed polarity for V+, V- and RLY.

Connect positive wire to V+, connect negative wire to V- and also connect neutral

wire to ground.

+V- is for power input connection, this unit has only one power input.

RLY is for relay connection.

Connecting procedure:

STEP 1 –

Take out 4 pin terminal block located in the included mounting kit package.

STEP 2 –

Connect power wire to +V- with correct polarity. Connect RLY for relay.

STEP 3 –

Plug into terminal block socket shown above. Polarity needs to match the V+ and V-

WARNING -- Always SHUTS OFF power source to connect power wire.

WARNING -- Any exceeded input voltage will not make this unit function

and may damage this unit.

LED indicator

LED

Color

State

Description

PWR

Green

Power is detected

OFF

Power is not detected

SFP Lnk/Act

Green

FX port is detected

Flashing

FX data is transmitting/receiving

TX Lnk/Act

Green

TX link is detected

Flashing

TX data is transmitting/receiving

TX PoE

Amber

PSE is activated and PD is detected

OFF

PSE is detecting PD

+V1- RLY

Specification

IEEE Standard

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 100Base-TX Fast Ethernet

IEEE 802.3ab 1000Base-T Gigabit Ethernet

IEEE 802.3z 1000Base-X Gigabit Ethernet

IEEE802.3x Flow Control and Back Pressure,

IEEE802.3af for POE

IEEE802.3at for POE+

Switch Architecture

Back-plane (Switching Fabric): 4Gbps

Data Processing

Store and Forward

Flow Control

IEEE 802.3x Flow Control and Back Pressure

Jumbo Frame

9KB

MAC address Table Size

Packet Buffer Size

Network Connector

1 x RJ-45 10/100/1000BaseT(X) PSE with POE

Output power up to 30Watts

1 x 100/1000M SFP

Network Cable

UTP/STP Cat.5e or above Cable

EIA/TIA-568 10-ohm (100m)

Fiber Cable (Multi-mode):50/125um,62.5/125um

Fiber Cable (Single-mode): 9/125um

Protocol

CSMA/CD

LED

PWR (Green): ON－Power is detected

OFF－Power is not detected

SFP Lnk/Act (Green): ON－FX port is detected

Flashing－FX data is transmitting/receiving

RJ-45 port:

Lnk/Act (Green): ON－TX port is detected

Flashing－TX data is transmitting

PoE (Amber): ON－PSE is activated and PD is detected

Flashing－PSE is detecting PD

POE Pin Assignment

30 watts 2 pairs

V-, V-, V+, V+ for pin 1, 2, 3, 6

DIP Switch

DIP 1: Reserved

DIP 2: ON－SFP port 100M

OFF－SFP port 1000M (Default)

Reverse polarity protection

Present

Overload current protection

Present

Power Supply

4 pin terminal block with 48V-56V VDC Power Input,

RLY (Relay): Relay switch for alarm

Alarm Relay Contact

Relay outputs with current carrying capacity of 1 A

@24VDC,

Relay in short circuit mode when power fails. in open

circuit mode when power supply is connected

Power Consumption

2 W@48 VDC full load, Without POE

Max total power 36Watts at 56VDC

Removable Terminal Block

Provide 4 pin terminal block

Wire range: 0.34mm^2 to 2.5mm^2

Solid wire (AWG):12-24/14-22

Stranded wire(AWG): 12-24/14-22

Torque:5lb-In/0.5Nm/0.56Nm

Wire Strip length: 7-8mm

Operating Temperature

-40°C~75°C fully tested.

Operating Humidity

5% to 95% (Non-condensing)

Storage Temperature

-40°C ~85°C

MTBF (mean time between

failure)

>500,000 hrs ( MIL-HDBK-217F) at 25°C

Housing

Rugged Aluminum, IP30 Protection

Case Dimension (L X W X D)

103.5 x 32 x 81.5 mm (L x W x D)

Installation mounting

DIN-Rail Mounting and Wall Mounting

Certifications

EN55022/24

ITE equipment

EN55011

Industrial, Scientific and Medical (ISM) equipment

Safety

IEC EN60950-1

EMC/EMS

CE, FCC, VCCI

EMI

FCC Part 15 Subpart B Class A,

CE EN 55022 Class A

EN 50155 / EN 60068-2-6

Vibration

EN 50155 / EN 60068-2-27

Shock

EN 50155 / EN 60068-2-32

Free Fall

Housing Dimension (mm)

Tabla de contenidos

Otros manuales de Convertidor de medios de LevelOne

LevelOne

LevelOne IEC-1300 Manual de usuario

LevelOne

LevelOne Infinity IEC-2000 Manual de usuario

LevelOne

LevelOne IEC-1800 Manual de usuario

LevelOne

LevelOne VDS-0120 PSE Manual de usuario

LevelOne

LevelOne FVT-2001 Manual de usuario

LevelOne

LevelOne POS-4000 Manual de usuario

LevelOne

LevelOne FVT-0103TXFC Manual de usuario

LevelOne

LevelOne VDS-1201 Manual del operador

LevelOne

LevelOne Infinity IEC-1020 Manual de usuario

LevelOne

LevelOne FVT-2001 Manual de usuario

LevelOne

LevelOne Infinity IEC-1000 Manual de usuario

LevelOne

LevelOne GVM-1101 Manual de usuario

LevelOne

LevelOne DSS-1000 Manual de usuario

LevelOne

LevelOne VDS-0110 Manual de usuario

LevelOne

LevelOne FVT-6001 Manual de usuario

LevelOne

LevelOne VDS-1201 Manual de usuario

LevelOne

LevelOne GVT-2010 Manual de usuario

LevelOne

LevelOne GVT-2000 Manual de usuario

LevelOne

LevelOne IEC-1220 Manual de usuario

LevelOne

LevelOne FVT-2002 Manual de usuario

LevelOne

LevelOne POI-2001 Manual de usuario

LevelOne

LevelOne POS-4001 Manual de usuario

LevelOne

LevelOne FVS-3800 Manual de usuario

LevelOne

LevelOne FVT-1101 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario