LevelOne PLI-2040 Manual de usuario
LevelOne
PLI-2040
200 Mbps HomePlug AV Adapter
User Manual
V1.0.0
HomePlug PowerLine
HomePlug PowerLine is an excellent solution that can be used to extend your network. In the home or small office
building, use HomePlug Ethernet Bridge Adapters to link multiple locations without the need to run Ethernet cable.
Combined with a broadband DSL/Cable connection, every room with electrical power outlets will have easy access
to high-speed Internet connection.
Introduction
200 Mbps HomePlug AV Adapter allows you to connect any device which has an Ethernet port to a PowerLine net-
work. In operation, the 200 Mbps HomePlug AV Adapter is completely transparent, and simply passes data
between the Ethernet port and the PowerLine network. The PowerLine data transfer rate can be reached up to 200
Mbps. Any device may be connected to the 200 Mbps HomePlug Ethernet Bridge’s Ethernet port, but a Windows
PC must be used for configuration.
* Strongly recommend Windows 2000/XP/Vista for utility configuration
Physical Details
Figure 1: 200 Mbps HomePlug AV Adapter
Front Panel LEDs
Power
On - Normal operation.
Off - No power
HomePlug
On - The PowerLine network is active. This means that at least one other HomePlug de-
vice was detected.
Off - PowerLine network is not available - no other HomePlug devices were detected.
Flashing - Data is being transmitted or received via the PowerLine network.
Ethernet
On - Ethernet connection is active.
Off - No Ethernet connection.
Flashing - Data is being transmitted or received via the Ethernet Port.
Setup
Configuration requires the use of Windows PC. Once configured, any device may be connected to the 200 Mbps
HomePlug AV Adapter's Ethernet port. To perform configuration, follow the procedures list below.
1. Connect a standard LAN cable from the 200 Mbps HomePlug AV Adapter's Ethernet port to your PC.
2. Plug the 200 Mbps HomePlug AV Adapter into a power outlet.
3. Wait a few seconds for startup to be completed, and then check the LEDs
The Power LED should be ON.
The HomePlug LED will be ON if other HomePlug devices are detected, otherwise it will be OFF.
The Ethernet LED should be ON.
4. Insert the supplied CD-ROM into your Windows PC, and wait for it to start, select “Utility”from the autorun
screen. If it does not start automatically, locate and run SETUP.EXE.
5. Follow the prompts to install the PLI-2040 utility.
6. Microsoft .NET Framework 1.1 is needed for installing PLI-2040 utility. The wizard will check automatically
whether the Microsoft .NET Framework 1.1 was installed on your PC or not. If not, the wizard will pop up a
message box. Click OK to install Microsoft .NET Framework 1.1 first.
Figure 2: Microsoft .NET Framework 1.1 Screen
7. Once installation is completed, run the PLI-2040 utility program. The first screen (Network Tab) will display in-
formation of the compatible devices found, such as their MAC Addresses and current transfer speeds.
Choose the desired device from the Device Selection, and the information of the selected device will be dis-
played in the table.
Figure 3: PLI-2040 Utility - Network Tab
8. Click Close to exit the PLI-2040 utility.
Setup is now complete.
If your PC is not the device you wish to use with the 200 Mbps HomePlug AV Adapter, connect the Ethernet ca-
ble from the 200 Mbps HomePlug AV Adapter to the desired device.
The 200 Mbps HomePlug AV Adapter is now ready for use.
Operation
Operation is completely automatic, and no user intervention is required.
If your HomePlug devices have difficulty communicating with each other, check the following:
Each HomePlug device must use the same Network Key.
You can use the Encryption tab of the PLI-2040 utility to assign a Network Key to other HomePlug devices.
200 Mbps HomePlug AV Adapter works better when plugged into the wall socket. Connect the 200 Mbps Ho-
mePlug AV Adapter into the power strip or surge protectors may degrade the network performance.
Specification
PowerLine Standards
HomePlug AV
Transfer Rate
Up to 200 Mbps
Modulation
1024/256/64/16/8 QAM, QPSK, BPSK
Forward Error Correction
Turbo Codes
Protocol
TDMA, CSMA/CA
Security
128-bit AES Encryption
LEDs
1 * Power
1 * HomePlug
1 * Ethernet
Ethernet Interface
1 * RJ45 LAN Port
Auto-negotiation, Auto MDI/MDIX
Ethernet Standards
Ethernet specification IEEE802.3, IEEE802.3u, IEEE802.3x
Power
100 - 240VAC, 50/60 Hz
Power Consumption
100mA (max.)
Operating Temperature
0C to 40C
Storage Temperature
-20C to 70C
Operating Humidity
10-90%RH (max)
Certifications
FCC Part 15 Class B
CE Mark
Safety Approvals
UL Listed (UL60950-1)/cUL CSA No.22-60950-01-03
CB, IEC/EN 60950-1;2001
Operating Systems
Windows 98SE, Windows ME, Windows 2000, Windows XP, Windows Vista or any
other operating system with network support
Tabla de contenidos
Otros manuales de Adaptador de LevelOne
LevelOne
LevelOne USB-0301 Manual de usuario
LevelOne
LevelOne WPC-0601 Manual de usuario
LevelOne
LevelOne USB-0401 Manual de usuario
LevelOne
LevelOne WUA-0616 Manual de usuario
LevelOne
LevelOne WNC-0101USB Manual de usuario
LevelOne
LevelOne WUA-1810E Manual de usuario
LevelOne
LevelOne USB-0301 Manual de usuario
LevelOne
LevelOne WUA-0601 Manual de usuario
LevelOne
LevelOne USB-0401 Manual de usuario
LevelOne
LevelOne USB-0501 Manual de usuario
LevelOne
LevelOne PLI-3410 Manual de usuario
LevelOne
LevelOne WPC-0101 Manual de usuario
LevelOne
LevelOne PLI-4052 Manual de usuario
LevelOne
LevelOne USB-0301 Manual de usuario
LevelOne
LevelOne GNC-0102T Manual de usuario
LevelOne
LevelOne FNC-0107TX Manual de usuario
LevelOne
LevelOne WUA-0616 Manual de usuario
LevelOne
LevelOne PLI-3510 Manual de usuario
LevelOne
LevelOne USB-0301 Manual de usuario
LevelOne
LevelOne USB-0502 Manual de usuario
