Leica TS03 Manual de usuario

Leica TS03/TS07

User Manual

Version 1.0

English

Introduction

Congratulations on the purchase of the Leica TS03/TS07.

This manual contains important safety directions as well as instructions for set-

ting up the product and operating it. Refer to "1 Safety Directions" for further

information.

Read carefully through the User Manual before you switch on the product.

The model and serial number of your product are indicated on the type plate.

Always refer to this information when you need to contact your agency or

Leica Geosystems authorised service centre.

•Windows is a registered trademark of Microsoft Corporation in the United

States and other countries

•

Bluetooth

®is a registered trademark of Bluetooth SIG, Inc.

All other trademarks are the property of their respective owners.

This manual applies to TS03 and TS07 instruments. Where there are differences

between the various instruments they are clearly described.

For the Tunnel application, refer to the separate manual "Leica TS03/TS07 Tun-

nel Application".

For the Mining application, refer to the separate manual "Leica TS03/TS07 Min-

ing Application".

On the last page of this manual, you can find the address of Leica Geosystems

headquarters. For a list of regional contacts, please visit

http://leica-geosystems.com/contact-us/sales_support.

myWorld@Leica Geosystems (https://myworld.leica-geosystems.com) offers

a wide range of services, information and training material.

With direct access to myWorld, you are able to access all relevant services

whenever it is convenient for you.

Service Description

myProducts Add all products that you and your company own

and explore your world of Leica Geosystems: View

detailed information on your products and update

your products with the latest software and keep up-

to-date with the latest documentation.

myService View the current service status and full service his-

tory of your products in Leica Geosystems service

centres. Access detailed information on the services

performed and download your latest calibration cer-

tificates and service reports.

Purchase

Product identification

Trademarks

Validity of this

manual

Leica Geosystems

address book

Service Description

mySupport Create new support requests for your products that

will be answered by your local Leica Geosystems

Support Team. View the complete history of your

support requests and view detailed information on

each request in case you want to refer to previous

support requests.

myTraining Enhance your product knowledge with Leica Geosys-

tems Campus - Information, Knowledge, Training.

Study the latest online training material on your

products and register for seminars or courses in your

country.

myTrustedServices Add your subscriptions and manage users for Leica

Geosystems Trusted Services, the secure software

services, that assist you to optimise your workflow

and increase your efficiency.

Table of Contents

1 Safety Directions 8

1.1 General 8

1.2 Definition of Use 9

1.3 Limits of Use 9

1.4 Responsibilities 9

1.5 Hazards of Use 10

1.6 Laser Classification 13

1.6.1 13

1.6.2 14

1.6.3 14

1.6.4 15

1.6.5

General

Distancer, Measurements with Reflectors

Electronic Guide Light EGL

Laser Plummet

AutoHeight Laser Plummet 16

1.7 Electromagnetic Compatibility EMC 17

1.8 FCC Statement, Applicable in U.S. 18

1.9 ICES-003 Statement, Applicable in Canada 20

2 Description of the System 21

2.1 System Components 21

2.2 Container Contents 22

2.3 Instrument Components 23

3 User Interface 25

3.1 Keyboard 25

3.2 Screen 26

3.3 Status Icons 26

3.4 Icon Pop-up Bubbles 29

3.5 Softkeys 30

3.6 Operating Principles 31

3.7 Pointsearch 32

3.8 Graphic Symbols 33

4 Operation 35

4.1 Instrument Setup 35

4.2 Batteries 38

4.2.1 Operating Principles 38

4.2.2 Battery for the TS Instrument 39

4.3 Data Storage 39

4.4 Main Menu 40

4.5 Distance Measurements - Guidelines for Correct Results 42

5 Settings 44

5.1 Work Settings 44

5.2 Regional Settings 46

5.3 Data Settings 49

5.4 Screen & Audio Settings 50

5.5 EDM Settings 52

5.6 Interface Settings 57

5.7 FTP Client 58

5.8 Internet Settings 60

5.9 Adjust 61

5.10 Startup Sequence 62

5.11 System Information 62

5.12 Licence Keys 65

5.13 Instrument Protection with PIN 65

5.14 Loading Software 66

4 Table of Contents

6 Apps - Getting Started 68

6.1 Overview 68

6.2 Starting an App 68

6.3 Setting the Job 69

6.4 Station Setup 70

7 Apps 72

7.1 Common Fields 72

7.2 Station Setup 72

7.2.1 Starting 72

7.2.2 Measuring the Target Points 75

7.2.3 Station Setup Results 77

7.3 Surveying 80

7.4 Setout 80

7.5 Reference Line 84

7.5.1 Overview 84

7.5.2 Defining the Base Line 84

7.5.3 Defining the Reference Line 85

7.5.4 Measure Line & Offset 86

7.5.5 Stakeout 87

7.5.6 Grid Stakeout 89

7.5.7 Line Segmentation 91

7.6 Reference Arc 94

7.6.1 Overview 94

7.6.2 Defining the Reference Arc 94

7.6.3 Measure Line & Offset 96

7.6.4 Stakeout 97

7.7 Reference Plane 100

7.8 Tie Distance 102

7.9 Area & DTM Volume 104

7.9.1 Overview 104

7.9.2 2D / 3D Area 106

7.9.3 Area to Reference Plane 107

7.9.4 DTM Volume 108

7.9.5 Area Division 111

7.10 Remote Height 113

7.11 COGO 114

7.11.1 Starting 114

7.11.2 Inverse and Traverse 115

7.11.3 Intersections 115

7.11.4 Offsets 117

7.11.5 Line - Extension 118

7.12 Road 2D 118

7.13 Road 3D 121

7.13.1 Starting 121

7.13.2 Basic Terms 122

7.13.3 Creating or Uploading Alignment Files 126

7.13.4 Stake 128

7.13.5 Check 129

7.13.6 Stake Slope 130

7.13.7 Check Slope 133

7.14 Traverse 134

7.14.1 Overview 134

7.14.2 Starting and Configuring Traverse 135

7.14.3 Measuring Traverse 137

7.14.4 Moving ahead 139

Table of Contents 5

7.14.5 Closing a Traverse 140

7.15 Tunnel 143

8 Favourites 144

8.1 Overview 144

8.2 Target Offset 145

8.2.1 Overview 145

8.2.2 Cylindrical Offset 146

8.3 Hidden Point 148

8.4 Check Tie 149

8.5 EDM Tracking 150

8.6 Backsight Check 151

8.7 SketchPad 151

9 Coding 153

9.1 Coding 153

9.2 Quick Coding 154

10 MapView Interactive Display Feature 156

10.1 Overview 156

10.2 Accessing MapView 156

10.3 Configuring MapView 156

10.4 MapView Components 157

10.4.1 Screen Area 157

10.4.2 Keys, Softkeys and Toolbar 157

10.4.3 Point Symbols 158

10.5 Selecting Points 159

11 Imaging & Sketching 160

11.1 Screenshot 160

11.2 Sketching 160

11.3 Image Management 161

12 Data Management 163

12.1 Manage 163

12.2 Exporting Data 164

12.3 Importing Data 168

12.4 Working with a USB Memory Stick 170

12.5 Working with the SD Card 171

12.6 Working with the Internal Memory 172

12.7 Working with Bluetooth 173

12.8 Working with the SIM Card 173

13 Check & Adjust 175

13.1 Overview 175

13.2 Preparation 175

13.3 Adjusting Line-of-Sight and Vertical Index Error 176

13.4 Adjusting the Compensator 178

13.5 Adjusting the Tilting Axis Error 179

13.6 Adjusting the Circular Level of the Instrument and Tribrach 180

13.7 Adjusting the Circular Level of the Prism Pole 181

13.8 Inspecting the Laser Plummet of the Instrument 181

13.9 Servicing the Tripod 182

14 mySecurity 183

15 Care and Transport 185

15.1 Transport 185

15.2 Storage 185

15.3 Cleaning and Drying 186

6 Table of Contents

16 Technical Data 187

16.1 Angle Measurement 187

16.2 Distance Measurement with Reflectors 187

16.3 Distance Measurement without Reflectors

(Non-Prism mode)

188

16.4 Distance Measurement Reflector (>4.0km) 189

16.5 Conformity to National Regulations 190

16.5.1 TS03 190

16.5.2 TS07 190

16.5.3 Dangerous Goods Regulations 191

16.6 General Technical Data of the Product 191

16.7 Scale Correction 195

16.8 Reduction Formulas 196

17 Software Licence Agreement 199

Appendix A Menu Tree 200

Appendix B Directory Structure 201

Table of Contents 7

1 Safety Directions

1.1 General

The following directions enable the person responsible for the product, and the

person who actually uses the equipment, to anticipate and avoid operational

hazards.

The person responsible for the product must ensure that all users understand

these directions and adhere to them.

Warning messages are an essential part of the safety concept of the instru-

ment. They appear wherever hazards or hazardous situations can occur.

Warning messages...

•make the user alert about direct and indirect hazards concerning the use

of the product.

•contain general rules of behaviour.

For the users‘ safety, all safety instructions and safety messages shall be

strictly observed and followed! Therefore, the manual must always be available

to all persons performing any tasks described here.

DANGER, WARNING, CAUTION and NOTICE are standardised signal words for

identifying levels of hazards and risks related to personal injury and property

damage. For your safety, it is important to read and fully understand the fol-

lowing table with the different signal words and their definitions! Supplemen-

tary safety information symbols may be placed within a warning message as

well as supplementary text.

Type Description

DANGER Indicates an imminently hazardous situation

which, if not avoided, will result in death or

serious injury.

WARNING Indicates a potentially hazardous situation or

an unintended use which, if not avoided,

could result in death or serious injury.

CAUTION Indicates a potentially hazardous situation or

an unintended use which, if not avoided,

may result in minor or moderate injury.

NOTICE

Indicates a potentially hazardous situation or

an unintended use which, if not avoided,

may result in appreciable material, financial

and environmental damage.

☞Important paragraphs which must be adhered

to in practice as they enable the product to

be used in a technically correct and efficient

manner.

Description

About warning

messages

8 Safety Directions

1.2 Definition of Use

•Measuring horizontal and vertical angles.

•Measuring distances.

•Recording measurements.

•Visualizing the aiming direction and vertical axis.

•Data communication with external appliances.

•Computing by means of software.

•Use of the product without instruction.

•Use outside of the intended use and limits.

•Disabling safety systems.

•Removal of hazard notices.

•Opening the product using tools, for example screwdriver, unless this is

permitted for certain functions.

•Modification or conversion of the product.

•Use after misappropriation.

•Use of products with recognisable damages or defects.

•Use with accessories from other manufacturers without the prior explicit

approval of Leica Geosystems.

•Deliberate dazzling of third parties.

•Controlling of machines, moving objects or similar monitoring application

without additional control and safety installations.

•Aiming directly into the sun.

•Inadequate safeguards at the working site.

1.3 Limits of Use

Suitable for use in an atmosphere appropriate for permanent human habita-

tion: not suitable for use in aggressive or explosive environments.

WARNING

Working in hazardous areas, or close to electrical installations or simi-

lar situations.

Life Risk.

Precautions:

▶Local safety authorities and safety experts must be contacted by the per-

son responsible for the product before working in such conditions.

1.4 Responsibilities

Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica

Geosystems, is responsible for supplying the product, including the User Man-

ual and original accessories, in a safe condition.

Intended use

Reasonably

forseeable misuse

Environment

Manufacturer of the

product

Safety Directions 9

The person responsible for the product has the following duties:

•To understand the safety instructions on the product and the instructions

in the User Manual.

•To ensure that it is used in accordance with the instructions.

•To be familiar with local regulations relating to safety and accident preven-

tion.

•To inform Leica Geosystems immediately if the product and the application

becomes unsafe.

•To ensure that the national laws, regulations and conditions for the opera-

tion of the product are respected.

1.5 Hazards of Use

NOTICE

Dropping, misusing, modifying, storing the product for long periods or

transporting the product

Watch out for erroneous measurement results.

Precautions:

▶Periodically carry out test measurements and perform the field adjust-

ments indicated in the User Manual, particularly after the product has been

subjected to abnormal use as well as before and after important measure-

ments.

DANGER

Risk of electrocution

Because of the risk of electrocution, it is dangerous to use poles, levelling

staffs and extensions in the vicinity of electrical installations such as power

cables or electrical railways.

Precautions:

▶Keep at a safe distance from electrical installations. If it is essential to

work in this environment, first contact the safety authorities responsible

for the electrical installations and follow their instructions.

WARNING

Lightning strike

If the product is used with accessories, for example masts, staffs, poles, you

may increase the risk of being struck by lightning.

Precautions:

▶Do not use the product in a thunderstorm.

Person responsible

for the product

10 Safety Directions

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Leica

Leica

Leica DISTO D810 touch Manual de usuario

Leica

Leica TS12P Manual de usuario

Leica

Leica Disto E7100i Manual de usuario

Leica

Leica Pinmaster Manual de usuario

Leica

Leica RANGEMASTER CRF 1200 Manual de usuario

Leica

Leica TS02 Manual de usuario

Leica

Leica TCR307 Manual de usuario

Leica

Leica tps1100 Manual de usuario

Leica

Leica Viva TS16 Manual de usuario

Leica

Leica Lino L2 Manual de usuario

Leica

Leica PINMASTER II PRO Manual de usuario

Leica

Leica TS11 Manual de usuario

Leica

Leica PIPER 100 Manual de usuario

Leica

Leica 3D Disto Manual de usuario

Leica

Leica RX1200 Manual de usuario

Leica

Leica Leica UTILIFINDER+ Manual de usuario

Leica

Leica DISTO A6 Manual de usuario

Leica

Leica RANGEMASTER CRF 800 Manual de usuario

Leica

Leica Disto D510 Manual de usuario

Leica

Leica NA320 Manual de usuario

Leica

Leica MOJO RTK Guía del administrador

Leica

Leica Builder T Manual de usuario

Leica

Leica Nova MS60 Manual de usuario

Leica

Leica Lino P5 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario