LEGRAND MicroRex D21 Plus Manual de usuario
0 6 12 16 24
2 41
N 292555/00
Technical data
4126 31 4126 32 4126 33
047 61 6047 60 047 63
Supply voltage: 230V 50/60Hz 120V 50/60Hz 24V AC/DC
Effective power consumption: Approx. 1 W
Contact rating: 1 changeover contact 16A 250V~µ cos ϕ = 1
Parallel compensation: 600W max. 70µF
Accuracy: ~ 0,1 s / day
single strand multi strand
Terminal capacity:1,5...4 mm2 1,5...2,5 mm2
Programmes : 56
Battery reserve: 5 years
Storage ambient: -20°C to +60°C
Working ambient: -20°C to +55°C
IP: 20
General information
• Start-up: after applying the supply voltage, the time switch
starts automatically with the last selected function. The relay
position is set by the current program.
• Battery backup
- Backlighting not active
- Data key READ/WRITE only via the menu
Set language
A
Day, Time, Date
Switch status
Function
Receptacle for
data key
Overview of programmed
switching times for the week.
Resolution 0.5h
Select menu, back to main menu,
Hold down > 1s = operating display
Confirm selection or load parameters
Select menu options or set parameters
Overview
Time switch
D21 - 1-channel
4 126 31 / 32 / 33 - 047 61 / 63 / 6047 60
®
!
Safety notes
This product should be installed in line with installation rules, preferably by a qualified electrician. Incorrect installation and use can lead to risk
of electric shock or fire. Before carrying out the installation read the instructions and take account of the product’s specific mounting location. Do not open
up, dismantle, alter or modify the device except where specifically required to do so by the instructions. All Legrand products must be opened and repaired
exclusively by personnel trained and approved by Legrand. Any unauthorised opening or repair completely cancels all liabilities and the rights to replacement
and guarantees. Use only Legrand brand accessories.
The device contains a LiMnO2 primary cell. When the product reaches the end of its life, this cell must be correctly removed and disposed of in accordance with
national legislation and the requirements of environmental protection.
GB
Operating principle: Typ 1.B. S. T.
IEC/EN 60730-1, IEC/EN 60730-2-7
Operation in a normal environment
Montage: in distribution panel, Degree of contamination: 2
Switch output, potential-free
a
dc
bg
This symbol indicates that the
selection is active.
* Only available in EXPERT mode.
2000 W
1000 W
2000 VA 600 W 70µF
+
c
R
2000 W
+
2000 W 2000 W
+
3680 W
Reset
Warning!
The memory will be cleared,
and all set data will be lost.
Hold down for more than 3 seconds and at
the same time press and release .
The language, time, date, summertime/winter-
time and
switching times will have to be re-entered.
Modes
• Auto - Automatic operation
• Constant ON
• Constant OFF
• Extra
The switch status imposed by the
program is inverted (manual override).
With the next effective switch command,
the time switch resumes control of on/off
switching.
4
Set time/date, summertime/wintertime
2
Summertime: ± 1 hour
Europe: Factory set
SPECIAL: The switchover to/from
summertime can be freely programmed by entering a start date and
end date and is then executed each year on the same day of the
week, e.g. Sunday
3Programming
A program consists of an ON time, OFF time and associated on and off days.
Programs with predefined on/off days (Mon to Sun, Mon to Fri and Sat and Sun): for these programs, you only need to set the switching times.
With the „INDIVIDUAL” option, you can allocate switching times to specific days of your choice.
The programs of a channel are combined with a logical OR.
*
*
CHRONO = All switch commands are executed in chronological order in a week
INPUT = Programs are executed in the order in which they are entered
Set MON and TUES
as on/off days
Contrast adjustment
5
Data key
1 h-Test
When this function is activated, the output is switched on for one hour.
After one hour, the time switch returns automatically to the programmed
mode.
Random function
Function to simulate presence.
Function active: the programmed switching cycles are shifted at random within the range of ± 15 minutes.
Hour counter
Displays the total relay ON time, (0 to 65535 h) and the date of the last reset.
Load the programs of the time switch on to a data key (WRITE KEY)
Warning! all programs stored on the data key will be overwritten.
or
or
Load the programs from the data key to the time switch (READ KEY)
Warning! all programs programmed in the time switch will be overwritten.
Pincode
PIN CODE active: The menus of the time switch will not be accessible unless the PIN CODE has been entered. When the pin code is active,
access to the button and key functions is disabled 1 minute after the last button press.
PIN free access can be re-enabled by selecting PASSIVE or by resetting the device.
Example
Expert mode
Some additional functions are available in Expert mode:
• Power grid synchronisation to improve the accuracy
• Cycle function
Note: Upon switching from ACTIVE to PASSIVE the additional menu items are hidden again and all the Expert mode settings are cancelled.
After re-activating, Expert mode will operate again with the basic settings.
Holiday
After activation the holiday program is executed between 0:00h on the start date and 24:00h on the end date (Constant ON/OFF). After the holi-
day program has run once, it must be reactivated.
Activating and deactivating grid synchronisation
Only available in EXPERT mode.
The default setting is PASSIVE. In order to improve the long-term accuracy, it is advisable to activate synchronisation if the time switch is
supplied from a on 50/60 Hz grid with frequency adjustment.
Cycle function
Only available in EXPERT mode
For cyclical switch commands the switching on time is set by logical “OR“ of programs of all types. A fixed cycle of ON and OFF time then ope-
rates within those limits. The cycle always starts with the ON time.
The cycle duration and the ON time within the cycle are the same length for all switching times. The cycle duration and the ON time can be set
independently in one-second increments. If the switching time is shorter than the cycle duration, the cycle will be shortened accordingly. The
ON time will remain unchanged. If the switching time is actually shorter than the ON time, the ON time will be shortened accordingly.
0:10:00 0:10:00 0:10:00
0:04:00 0:04:000:04:00
15:00:00 15:10:00 15:20:00 15:30:00
15:32:00
Program 1
Relais Chanal 1
Program n
min max
Period 2s 2h
Pulse 1s 1h 59min 59s
1
2
+
Switch off the device before dismantling the module. Do not switch on again until the module has been installed.
Always use a Li cell type battery (LiMnO2) CR2477, 3V, high temperature type min +70°C.
Tabla de contenidos
Otros manuales de Minutero de LEGRAND
LEGRAND
LEGRAND Wattstopper RT-100-I Manual de usuario
LEGRAND
LEGRAND Wattstopper RT-200-W Manual de usuario
LEGRAND
LEGRAND LEXIC 037 25 Manual de usuario
LEGRAND
LEGRAND WattStopper RT-50 Manual de usuario
LEGRAND
LEGRAND LEXIC 037 05 Manual de usuario
LEGRAND
LEGRAND EconoRex MT 499 83 Manual de usuario
LEGRAND
LEGRAND PRO 21 781 50 Series Manual de usuario
LEGRAND
LEGRAND MaxiRex 4T 649 917 Manual de usuario
LEGRAND
LEGRAND MicroRex D11 Basic Manual de usuario
LEGRAND
LEGRAND LEXIC 037 81 Manual de usuario
LEGRAND
LEGRAND Lexic MicroRex D22 Manual de usuario
LEGRAND
LEGRAND LEXIC RondoRex w21 Series Manual de usuario
LEGRAND
LEGRAND 49730 Manual de usuario
LEGRAND
LEGRAND LEXIC 037 64 Manual de usuario
LEGRAND
LEGRAND Pass&Seymour RT1 Manual de usuario
LEGRAND
LEGRAND LEXIC MicroRex T11 Manual de usuario
LEGRAND
LEGRAND LEXIC Rex2000 D21F Manual de usuario
LEGRAND
LEGRAND Wattstopper RT-20 Manual de usuario
LEGRAND
LEGRAND MaxiRex D72/2 Plus Series Manual de usuario
LEGRAND
LEGRAND D817SLIMDP Manual de usuario
