LEGRAND Vaddio RF Manual de usuario
Document Number 411-0058-40 Rev A – August 2021
User Guide for the
Vaddio RF Remote Commander
August 2021
998-2180-000 (Worldwide)
The Vaddio RF Remote Commander provides basic camera and conference
functionality – pan, tilt, zoom, presets, volume control, and muting, as applicable.
You can also use the remote to get the camera's IP address. This remote is a radio-
frequency device, and is not compatible with products that use IR (infrared)remotes.
Before you can use the RF remote, you will need to:
nInstall the batteries
nPair the remote with the camera
Installing the Batteries
The Vaddio RF Remote Commander uses two AAA batteries.
1. Remove the cover from the back of the remote. You may need to press down on
the inner edge while sliding it off.
2. Install the batteries as shown in the diagram in the battery compartment.
3. Slide and snap the cover back into place.
Pairing the Remote to the Camera
The camera does not recognize or respond to the remote until they are paired. Do
this after the camera is turned on and its status light is white.
To pair the remote using the camera’s IP button:
1. Press and hold the camera’s IP button until the status light blinks cyan.
2. While the camera’s status light blinks cyan, press the pairing button on the remote. The camera's
status light changes to steady white when the remote is paired. You may need to press the remote's
pairing button more than once.
3. If the status light changes color and keeps blinking, the pairing was not successful. Reboot the
camera and go back to step 1. If the problem persists, contact Vaddio Technical Support.
To pair the remote using the camera’s administrative web interface:
1. On the Pairing page of the web interface, select Pair Remote.
2. When the camera's status light blinks cyan, press and hold the pairing button on the remote until the
status light changes to steady white.
RF Remote Quick Reference
The Vaddio RF Remote Commander may have controls for capabilities that your camera does not have.
Some buttons behave in different ways depending on the model of camera.
Indicator and Power button – Set the camera to standby
mode, or return to full-power mode.
Function buttons – Reserved for future use.
Arrow buttons – Pan and tilt. For cameras with Auto-
framing capability, Auto-framing pauses if you use these
buttons.
Home button – Function depends on the model of camera.
For cameras with Auto-framing capability, Auto-framing
resumes when you press this button.
Network button – Display the camera's IP address on the
video output.
Pairing button – Use when pairing the remote with the
camera.
Mute button – Mute the microphone(s).
Reserved for future use.
Volume +/– button – Increase or decrease the volume from
the connected speaker.
Focus +/– buttons – Adjust the focal distance in or out,
when Manual focus mode is selected.
Zoom +/– button– Increase or decrease the zoom.
Auto and Man buttons – Select automatic or manual focus.
Preset buttons – Set, clear, or select preset shots.For
cameras with Auto-framing capability, Auto-framing pauses if
you use these buttons.
User Guide for the Vaddio RF Remote
2
Vaddio is a brand of Legrand AV Inc.· www.legrandav.com · Phone 800.572.2011 / +1.763.971.4400 ·
Vaddio is a registered trademark of Legrand AV Inc. All other brand names or marks are used for
identification purposes and are trademarks of their respective owners. All patents are protected under
existing designations. Other patents pending.
©2021 Legrand AV Inc.
Other Things to Know About the Remote
Here are some common situations in which the Vaddio RF Remote Commander can behave in ways you
don't expect.
nEnvironments with cameras in adjacent rooms – If the remote is currently paired to a camera and
within range of that camera, it will not pair with another camera.
nThe remote goes to standby mode after a brief period of inactivity. Press a button to wake it up.
nThe remote is no longer paired after restoring the camera's factory defaults. If you restore
factory defaults on the camera, pair it with the remote again.
Unpairing the Remote
If you need to unpair the remote from the camera that currently recognizes it, you will need to log in to the
camera's web interface as admin. On the Pairing page, select Forget Remote.
User Guide for the Vaddio RF Remote
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Mando a distancia de LEGRAND
LEGRAND
LEGRAND MKFOB v2 Manual de usuario
LEGRAND
LEGRAND 0 882 32 Manual de usuario
LEGRAND
LEGRAND ADMHRM4 Manual de usuario
LEGRAND
LEGRAND Wattstopper LMRH-101 Manual de usuario
LEGRAND
LEGRAND Qmotion QDR2 Manual de usuario
LEGRAND
LEGRAND FSIR-100 Instrucciones de funcionamiento e instalación
LEGRAND
LEGRAND RCFREMOTE Manual de usuario
LEGRAND
LEGRAND VADDIO HuddleSHOT Remote Manual de usuario
LEGRAND
LEGRAND FB Advanced Manual de usuario
LEGRAND
LEGRAND QMotion Manual de instalación
LEGRAND
LEGRAND DPX 400 Hoja de datos
LEGRAND
LEGRAND 348220 Manual de usuario
LEGRAND
LEGRAND FB Advanced Manual de instrucciones
LEGRAND
LEGRAND Pass & Seymour LightSense PSWRR Manual de usuario
LEGRAND
LEGRAND 882 30 Manual de usuario
LEGRAND
LEGRAND In One 882 00 Manual de usuario
LEGRAND
LEGRAND 0 676 95 Manual de usuario
LEGRAND
LEGRAND 882 32 Manual de usuario
LEGRAND
LEGRAND DPX 1250 Manual de usuario
LEGRAND
LEGRAND Qmotion QDR2 Manual de usuario
