LEGRAND EasyIP VADDIO PCC Manual de usuario
Document Number 411-0068-31 Rev B – October 2023
Installation Guide for the
EasyIP PCC and PCC Mini
Four-Camera Joystick Controllers
Overview
This guide provides information about:
nEasyIP PCC four-camera joystick controller, 999-57755-000 (worldwide)
nPCC Mini four-camera joystick controller, 999-57750-000 (worldwide)
About this guide
This guide covers:
nControls and connections
nTips for a successful installation
nConnection diagram
nEquipment power-on
Complete product information is available in the Complete Manual
for the EasyIP PCCFour-Camera Joystick Controller.
Features
nSimple control of up to four cameras:
oEasyIP PCC for EasyIP cameras
oPCC Mini for other Vaddio cameras
nThree-axis Hall effect joystick
nIlluminated pushbuttons for camera selection
nWeb interface for operation and administrative control
nUse with the Vaddio Device Controller or manage from your PC
nYour EasyIP Switch powers the EasyIP PCC; a PoE+ mid-span power injector powers the PCC Mini
A quick look at the camera controller
The EasyIP PCC and PCC Mini look identical except for the model information.
Camera buttons (lower row)– Select the camera to use for the next shot (the preview camera). The
buttons are only illuminated if they are assigned to cameras.
Preset buttons (upper row) – Use these buttons to select presets 1 through 4 on the selected preview
camera. The buttons are only illuminated if the corresponding presets have been stored on the camera.
Joystick – Left/right to pan, forward/back to tilt, twist to zoom.
Kensington lock slot – Keep your joystick from adventuring away into the wide, wonderful world.
PoE+ Gigabit Ethernet port – Power and network connectivity, including access to cameras.
Courtesy HDMI output – Video from the camera you are currently controlling.
IP button – Press to overlay the device's IP address on the HDMI video output display.
Installation Guide for the EasyIP PCC Four-Camera Joystick Controller
2
Installation
This section covers how to install and connect the product. It also provides safety information and other
guidance related to installing the product.
Note
This product is intended for installation and use only in environments where all RS-232 and PoE/PoE+
connections originate within the building.
Or in UL's preferred phrasing...
PoE-type networks connected to this equipment are for intra-building use only and should not
be connected to lines that run outside the building in which this product is located.
Don’t void your warranty!
Caution
This product is for indoor use. Do not install it outdoors or in a humid environment without the appropriate
protective enclosure. Do not allow it to come into contact with any liquid.
Do not install or operate this product if it has been dropped, damaged, or exposed to liquids. If any of
these things happen, return it to Vaddio for safety and functional testing.
Cabling notes
Best practices for making cables:
nUse Cat-5e or better cable. We recommend shielded cabling if the cables will be coiled,
run tightly with other cables, or placed close to sources of electromagnetic interference
such as power lines or fluorescent light fixtures.
nUse high-quality standard RJ-45 connectors; 568B termination recommended.
nUse a high-quality crimping tool.
Caution
When building cables for Vaddio products, do not use pass-through RJ-45 connectors. If
they are crimped incorrectly, they can cause intermittent connections and degrade
signal quality. Incorrectly crimped pass-through connectors can also damage the
connectors on the product, which will void your warranty.
Intact – will make reliable contact
with the cable connector
Damaged – Bent contact fingers
will NOT make reliable contact
with the cable connector
Caution
Check your cables. Connecting a cable to the wrong port or using the wrong pin-out can result in
equipment damage and will void the warranty.
Pro tip
To prevent tragic mishaps, label both ends of every cable.
3
Installation Guide for the EasyIP PCC Four-Camera Joystick Controller
Basic connections
Because the EasyIP PCC and PCC Mini are for different environments, the connections are different.
Connecting the EasyIP PCC controller
The EasyIP PCC connects to the EasyIP Switch that powers the rest of the EasyIP installation. A Vaddio
Device Controller provides access to the web interfaces of all the EasyIP products connected to the
switch.
Installation Guide for the EasyIP PCC Four-Camera Joystick Controller
4
Connecting the PCC Mini controller
The PCC Mini connects to the network via a PoE+ mid-span power injector. A Vaddio Device Controller
provides access to Vaddio products on the same subnet.
Ensuring compatibility
The controller may be unable to communicate with Vaddio cameras if their firmware is out of date. When
you set up the controller, be sure the associated cameras have been updated to the latest firmware.
Powering up
When you power up the device for the first time, you will need to access the web interface to configure it
for operation.
Next steps
The joystick controller is now ready to configure. Until the product is configured, it is not functional. Refer
to the Complete Manual for the EasyIP PCC and PCC Mini Four-Camera Joystick Controllers.
5
Installation Guide for the EasyIP PCC Four-Camera Joystick Controller
Vaddio is a brand of Legrand AV Inc. · www.legrandav.com · Phone 800.572.2011 / +1.763.971.4400 · Email Europe, Middle East,
Vaddio is a registered trademark of Legrand AV Inc. All other brand names or marks are used for identification purposes and are
trademarks of their respective owners. All patents are protected under existing designations. Other patents pending.
©2023 Legrand AV Inc.
Operation, storage, and care
For smears or smudges on the product, wipe with a clean, soft cloth. Do not use any abrasive chemicals.
Keep this device away from food and liquids.
Do not operate or store the device under any of the following conditions:
nTemperatures above 40°C (104°F) or below 0°C (32°F)
nHigh humidity, condensing or wet environments
nInclement weather
nSevere vibration
nCorrosive atmosphere
nDry environments with an excess of static discharge
nAs a shield while dueling (the dimensions are all wrong for that)
Do not attempt to take this product apart. There are no user-serviceable components inside.
Installation Guide for the EasyIP PCC Four-Camera Joystick Controller
Otros manuales para EasyIP VADDIO PCC
1
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Controladores de LEGRAND
LEGRAND
LEGRAND 0 884 12 Manual de usuario
LEGRAND
LEGRAND 0 784 48 Manual de usuario
LEGRAND
LEGRAND 0 675 97 Manual de usuario
LEGRAND
LEGRAND 0 035 40 Manual de usuario
LEGRAND
LEGRAND Wattstopper LMRC-111-16M Manual de usuario
LEGRAND
LEGRAND Wattstopper LMPL-101 Manual de usuario
LEGRAND
LEGRAND Arteor 5 742 07 Manual de usuario
LEGRAND
LEGRAND Pass & Seymour RFP Manual de usuario
LEGRAND
LEGRAND 5739 12 Manual de instrucciones
LEGRAND
LEGRAND 0 698 74L Manual de usuario
LEGRAND
LEGRAND Arteor Manual de usuario
LEGRAND
LEGRAND radiant Manual de usuario
LEGRAND
LEGRAND Adorne LC7001 Manual de usuario
LEGRAND
LEGRAND Tynetec ZXT473 Manual de usuario
LEGRAND
LEGRAND Pass & Seymour LightSense PSHCF Manual de usuario
LEGRAND
LEGRAND Wattstopper DCLV2 Manual de servicio
LEGRAND
LEGRAND adorne WNAL33/43 Manual de usuario
LEGRAND
LEGRAND EasyIP VADDIO PCC Manual de usuario
LEGRAND
LEGRAND ALPTEC 5.2 Manual de usuario
LEGRAND
LEGRAND MRD6 v2 Manual de usuario
