Ledj RGB DMX Manual de usuario

www.prolight.co.uk

RGB DMX Deck Skirt

2.1M x 1M Starcloth (order code: STAR25)

USER MANUAL

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

LEDJ RGB DMX Deck Skirt Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

Operating modes:

1, Stand Alone with Sound Activation

2, DMX operation

For Sound Activation:

With the power turned off set dip switch 10 to ON and all others to OFF. Turn on the power and

the sensitivity control can now be set to the desired level.

For DMX operation:

With the power turned off set dip switch 10 to OFF, then using dip switches 1 - 9 set the desired

DMX address and then turn on the power. You can now control the RGB deck skirt using the table

below.

DMX table:

LEDJ RGB DMX Deck Skirt Technical specications

0-9

10-19

20-29

30-39

40-49

50-59

60-69

70-79

80-89

90-99

100-109

110-119

120-129

130-139

140-149

150-159

160-169

170-179

180-189

190-199

200-209

210-219

220-229

230-239

Channel DMX Number Function

Channel 1

Blackout

Pattern number 1

Pattern number 2

Pattern number 3

Pattern number 4

Pattern number 5

Pattern number 6

Pattern number 7

Pattern number 8

Pattern number 9

Pattern number 10

Pattern number 11

Pattern number 12

Pattern number 13

Pattern number 14

Pattern number 15

Pattern number 16

Pattern number 17

Pattern number 18

Pattern number 19

Pattern number 20

Pattern number 21

Pattern number 22

Pattern number 23

Side view:

LEDJ RGB DMX Deck Skirt Technical specications

240-249

250-255

0-255

Channel DMX Number Function

Pattern number 24

Auto run through all programmes

Animates the pattern selected on channel 1

(The higher the number the faster the speed)

Channel 1

(continued)

Channel 2

Back view:

Identcation:

1, Power switch

2, Power supply

3, Fuse

4, Volume control

5, Microphone

6, Starcloth power output

7, Starcloth signal output

8, Dip switches

9, DMX in

10, DMX out

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest exibility when it comes

to customising or creating a show. In this mode you will be able to control each individual trait of

the xture and each xture independently.

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each xture requires a

“start address” from 1- 511. A xture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a xture that occupies or uses 7

channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

Set the start address using the group of dip switches located usually on the back of the xture.

Each dipswitch has an associated value. Adding the value of each switch in the ON position will

provide the start address. Determining which switches to toggle ON given a specic start address

can be accomplished in the following manner. By subtracting the largest switch value possible

from the selected start address until zero is achieved.

EXAMPLE STARTING ADDRESS

Address 10

Pin NO: 4 = 8

Pin NO: 2 = 2

Total = 10

Address 24

Pin NO: 5 = 16

Pin NO: 4 = 8

Total = 24

DMX address using

simple maths

233 - (128 = 105,Turn on dip No: 8

105 - (64) = 41,Turn on dip No:7

41 - (32) = 9,Turn on dip No: 6

9 - (8) = 1,Turn on dip No: 4

1 - (1) = 0,Turn on dip No:1

You will most likely use the first available

number which maybe Number 1.This

number was selected for

example purposes

DIP SWITCH (DMX VALUE)

128

256

LEDJ RGB DMX Deck Skirt DMX control mode

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication between

intelligent xtures and controllers. A DMX controller sends DMX data instructions form the

controller to the xture. DMX data is sent as serial data that travels from xture to xture via the

DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers only have

a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to be linked together

and operate from a single controller, as long as all xtures and the controller are DMX compliant.

To ensure proper DMX data transmission, when using several DMX xtures try to use the

shortest cable path possible. The order in which xtures are connected in a DMX line does not

inuence the DMX addressing. For example; a xture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. When a

xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to

address 1 to that unit, no matter where it is located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The RGB Deck Skirt can be controlled via DMX-512 protocol. The DMX address is set on the

back of the unit. Your unit and your DMX controller require a standard 3-pin XLR connector for

data input/output (gure 1).

Figure 1

Also remember that DMX cable must be daisy chained and cannot be split.

LEDJ RGB DMX Deck Skirt DMX set up

Further DMX cables can be purchased from all

good sound and lighting suppliers or Prolight

dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

Notice:

• Be sure to follow gures 2 & 3 when making your own cables. Do not connect the cable’s shield

conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer

casing. Grounding the shield could cause a short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the last unit to

avoid erratic behaviour.

Using a cable terminator (part number CABL90) will decrease the possibilities of erratic

behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of 3-pin. 5-Pin

XLR xtures may be implemented in a 3-pin XLR DMX line. When inserting standard 5-pin

XLR connectors in to a 3-pin line a cable adaptor must be used. The Chart below details the

correct cable conversion.

Termination reduces signal transmission problems

and interferance. it is always advisable to connect a

DMX terminal, (resistance 120 Ohm 1/4 W) between

pin 2 (DMX-) and pin 3 (DMX+) of the last fixture.

LEDJ RGB DMX Deck Skirt DMX Set Up

LEDJ RGB DMX Deck Skirt Dip Switch Reference Chart

DMX Dip Switch Quick Reference Chart

Dip Switch Position

Maintenance

The RGB DMX Deck Skirt requires almost no maintenance. However, you should keep the unit

clean, otherwise, the xture’s light-output will be signicantly reduced. Disconnect the mains power

supply, and then wipe the cover with a damp cloth. Do not immerse in liquid. The cloth will require

monthly cleaning, as smoke-uid tends to build up residues, reducing the light-output very quickly.

Do not use alcohol or solvents. Keep connections clean. Disconnect the power, and then wipe the

connections with a damp cloth. Make sure connections are thoroughly dry before re-connecting

the

power supply.

The following points have to be considered during the inspection:

1. All screws used for installing the device have to be tightly connected and must not be corroded.

2. There should not be any deformations on housing, xing and installation points.

3. The electric power supply cables must not show any damages or material fatigue.

Replacing a Fuse

Power surges, short-circuit or inappropriate electrical power supply may cause a fuse to fail. If the

fuse fails, the product will not function whatsoever. If this happens, follow the directions below.

1. Unplug the unit from electric power supply.

2. Insert a at-headed screwdriver into a slot in the fuse cover. Turn the screwdriver to the left, at

the same time gently push (Turn and Push). The fuse will come out.

3. Remove the used fuse. If brown or unclear, it has failed.

4. Insert the replacement fuse into the holder where the old fuse was. Reinsert the fuse cover.

Be sure to use a fuse of the same type and specication. See the product specication

label for details.

Technical Specications:

Voltage: 240V AC 50Hz

Wattage: 5W

LED’s: R: 32, G: 32, B: 32 (Total: 96)

Dimensions: 2.1m x 1m

Weight: 3kgs

LEDJ RGB DMX Deck Skirt Maintenance

Tabla de contenidos

Otros manuales de Equipo de iluminación de Ledj

Ledj

Ledj Spectra Par 15Q8 PRO Manual de usuario

Ledj

Ledj ECO LED Par 56 Manual de usuario

Ledj

Ledj Libretto Mini RGBAL Profile Manual de usuario

Ledj

Ledj HBR 1D Manual de usuario

Ledj

Ledj LEDJ24 Manual de usuario

Ledj

Ledj 18HEX10 PRO Manual de usuario

Ledj

Ledj Slimline Q5 Series Manual de usuario

Ledj

Ledj Event Panel Manual de usuario

Ledj

Ledj Stage Wash 18 Manual de usuario

Ledj

Ledj BlockBuster 6 Manual de usuario

Ledj

Ledj Pixel Bar LEDJ73A Manual de usuario

Ledj

Ledj Intense 9P10 RGBWA LED Slim Panel Manual de usuario

Ledj

Ledj Spectra Flood 18HEX10 Manual de usuario

Ledj

Ledj Spectra Par LEDJ88 Manual de usuario

Ledj

Ledj SPECTRA PAR 7T3 Manual de usuario

Ledj

Ledj HEX Par 9 LEDJ226 Manual de usuario

Ledj

Ledj Omni Tri-9 Manual de usuario

Ledj

Ledj Spectra Q40 MKII Manual de usuario

Ledj

Ledj FS300 Manual de usuario

Ledj

Ledj LEDJ387 Manual de usuario

Ledj

Ledj Slimline 1T100 Manual de usuario

Ledj

Ledj Stage Par CZ200 3200K Manual de usuario

Ledj

Ledj Artisan 1000 Manual de usuario

Ledj

Ledj LEDJ472 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario