Lectrosonics HMA-941 Series Manual de usuario

Quick

Start

Guide

Fill in for your records:

Serial Number:

Purchase Date:

This guide is intended to assist with

initial setup and operation of your

Lectrosonics product.

For a detailed user manual, down-

load the most current

version at:

www.lectrosonics.com/manuals

HMa-941

Plug-On Transmitter

30 November 2018

Digital Hybrid Wireless®

U.S. Patent 7,225,135

For FCC Part 74 licensed operators

LECTROSONICS, INC.2

LCD Screen

Backlit for easy viewing in bright or dimly lit conditions.

Pwr (power) LED

Indicates power status and battery strength.

XLR Input Jack

Standard 3‑pin Switchcraft XLR type. Coupler is spring‑loaded to maintain a

snug ﬁt and to prevent noise.

Modulation LEDs

Provides a visual indication of the audio input signal level ‑ either red or green

to indicate modulation levels.

AUDIO Button

Used to display the view and adjust the audio gain setting (0 dB to 44 dB).

FREQ Button

Used to set the operating frequency and toggle the LCD between the operating

frequency in MHz and a two‑digit hexadecimal frequency code.

UP/DOWN Arrows

Used to view and select parameters and values during setup and operation.

Battery Compartment Cover

Hinged to housing to prevent loss.

Antenna

An antenna is formed betiween the housing and the attached microphone,

operating much like a dipole. At UHF frequencies the length of the housing is

ismiliar to 1/4 wavelength of the operating frequency, so the antenna is supris‑

ingly efﬁcient, which helps extend the operating range and suppress noise

and interference.

Controls and Functions

Battery

Compartment

Cover

XLR Input

Jack

AUDIO Button

LCD

Input

Coupler

FREQ Button

Modulation

LEDs

PWR LED

UP Arrow

DOWN Arrow

www.lectrosonics.com 3

The transmitter is powered by two AA batteries.

Note: Standard zinc‑carbon batteries marked “heavy-duty” or “long-

lasting” are not adequate.

To install new batteries:

1. Slide open the Battery Cover and remove any old batteries.

2. Insert the new batteries into the housing. One battery goes in positive

(+) end ﬁrst, the other negative (‑) end ﬁrst. Look into the battery com‑

partment to determine which end goes in which side. The side with the

plastic ring is the side which accepts the positive end of the battery.

Note: It is possible to install the batteries backward and close the

battery door, but the batteries will not make contact and the unit will not

work.

3. Slide the Battery Cover until it snaps securely shut.

Battery Installation

Battery

Compartment

Battery

Cover

positive (+)

terminal

negative (–)

terminal

LECTROSONICS, INC.4

Operating Instructions

Power Up and Boot Sequence

1) Ensure that good batteries are installed in the unit.

2) Simultaneously press and hold the AUDIO and FREQ buttons until the power

on boot sequence is initiated.

The count will progress from 1 through 3 and the unit

will then power up with the RF output turned on.

During this turn on sequence, the modulation and

power LEDs all glow red, then green, and then revert

to normal operation. If the buttons are released before the count is com‑

plete, the unit will boot up into the standby mode (see below).

The LCD displays the following information during the boot sequence:

Company Name: LECtro

Frequency Block: b 941

Firmware Version (rX.X): r1.01 (typical)

Compatibility Mode: CP Hbr (typical)

When the boot sequence is complete, the display will switch to the frequency

currently set.

Power Down

Initial Power Off

Timer Screen

1) Simultaneously press and hold the AUDIO and FREQ buttons while observ‑

ing that the word “Off” appears in the LCD along with a counter.

2) When the counter reaches “0”, the unit turns off.

Note: If the AUDIO and FREQ buttons are released before the LCD

goes blank at the end of the countdown, the unit will not turn off.

Instead, it will stay energized and the display will return to the previous

screen.

Standby Mode

Standby Screen

With the power turned off, pressing the AUDIO

and FREQ buttons brieﬂy places the unit in

Standby Mode.

In this mode the RF output is turned off so all

setup adjustments can be made without interfering with other systems operat‑

ing in the same location. The screen displays “rf OFF” to remind the user that

the unit is not transmitting.

While the unit is in the standby mode, access the setup screens using the

AUDIO and FREQ buttons and make adjustments using the UP and DOWN

arrows.

www.lectrosonics.com 5

Menus

Setup is accomplished using menus and setup screens accessed by holding

the UP and DOWN arrow buttons at turn on, and by pressing the AUDIO and

FREQ buttons when the unit is turned on.

Hold UP arrow at turn on.

Hold the UP arrow button in while pressing both AUDIO and FREQ buttons to

access the setup screens below. It’s easier if you lay the unit on a ﬂat surface

and use two hands to press all three buttons at the same time. After the ﬁrst

screen loads, press the AUDIO button repeatedly to switch between the set‑

tings. Press the UP and DOWN arrow buttons for the desired selection.

After the settings are made, press both AUDIO and FREQ buttons together to

exit and turn the power off.

CP (compatibility modes)

Allows the transmitter to be used with 941 Series receivers or IFB systems in

the 941 MHz band.

nHb Digital hybrid mode

IFb Lectrosonics IFB systems

Pr (power output)

Can be set at 250 for extended range or at 50 for longer battery life.

50 50 mW output and longer battery life when

maximum range is not necessary

100 100 mW for slightly increased range

NOTE: See battery life table in the speciﬁcations

AP (audio polarity)

The polarity of the audio input (sometimes referred to as “phase”) can be

reversed for compatibility with other microphones.

PDenotes positive polarity

nDenotes negative polarity

StP (Frequency step size)

Sets the increments of frequency adjustment.

100 100 kHz steps

25 25 kHz steps

LECTROSONICS, INC.6

Hold DOWN arrow at turn on.

Hold the DOWN arrow button in while pressing both AUDIO and FREQ but‑

tons to access the setup screens below. It’s easier if you lay the unit on a ﬂat

surface and use two hands to press all three buttons at the same time. After

the ﬁrst screen loads, press the AUDIO button repeatedly to switch between

the settings. Press the UP and DOWN arrow buttons for the desired selection.

After the settings are made, press both AUDIO and FREQ buttons together to

exit and turn the power off.

rc (remote control with mobile app)

Allows the transmitter to respond to remote control “dweedle” tones from a

mobile device, or from tones generated by the Lectrosonics RM and RM2

devices.

on Enables the remote function.

oFF Disables the remote function.

PbAc (auto power restore)

Sets the transmitter to automatically turn back on and return to the previous

state after a battery change or power interruption when it is in the operating

mode.

1 Restores power automatically

0 Does not restore power automatically

bL (backlight settings)

Adjusts how long the LCD stays lit after pressing buttons.

55 minutes

30 30 seconds

on Stays on

www.lectrosonics.com 7

AUDIO Button

When the unit is turned on in either the Standby or Operating Mode, pressing

the AUDIO button repeatedly switches between the available settings.

• LF (XX) adjusts the low frequency roll‑off of the audio signal.

• AUD (XX) adjusts the input gain

LF (XX) - Adjusting the Low Frequency Roll-off

Repeatedly press the AUDIO button until the LF roll‑off adjustment screen

appears. Then press and hold the AUDIO button while selecting the desired

roll‑off frequency with the UP and DOWN arrows.

The roll‑off frequency can be set to 35, 50, 70, 100, 120 and 150 Hz.

LECTROSONICS, INC.8

AUD (XX) - Adjusting Audio Level (Gain)

It’s generally a good idea to adjust the low frequency roll‑off before setting the

gain, since it could affect the gain adjustment. The control panel modulation

LEDs marked ‑10 and ‑20 indicate the audio level and limiter activity. Once

adjusted according to the following procedure, the transmitter’s audio level

setting should not be used to control the volume of your sound system or

recorder levels. This gain adjustment matches the transmitter gain with the

microphone’s output level, the user’s voice level and the position of the mi‑

crophone. The audio input level (gain) should be adjusted with the unit in the

Standby Mode while observing the LEDs.

It is generally best to set the LF roll‑off before adjusting the gain, since low

frequency energy can affect the input level to the transmitter.

It is desirable to to set the gain so that some limiting occurs on louder peaks.

The limiter is very transparent over a 43 dB range, and its effect is not audible

until the system is close to overload. In other words, don’t be shy about turn‑

ing up the gain.

It is actually a good idea to turn the gain up to maximum and listen for distor‑

tion or compression to get a feel for how much headroom is available.

Signal Level -20 LED -10 LED

Less than ‑20 dB Off Off

‑20 dB to ‑10 dB Green Off

‑10 dB to +0 dB Green Green

+0 dB to +10 dB Red Green

Greater than +10 dB Red Red

Note: If several different people will be using the transmitter and there is not

time to make the adjustment for each individual, adjust it for the loudest voice.

1) With the transmitter in the Standby Mode, plug in the microphone and make

sure the connector is ﬁrmly seated.

Warning: If the wireless system is powered up while connected

to a live sound system, be careful to turn the sound system level

down ﬁrst or severe feedback can occur.

2) Position the microphone in the location where it will be used in actual op‑

eration.

3) Observe the modulation LEDs while speaking or singing into the micro‑

phone at the same voice level that will be used during operation. While

holding the AUDIO button, press the UP or DOWN arrow buttons until the

both the ‑20 and ‑10 LEDs glow green, with the ‑20 LED ﬂickering red dur‑

ing louder peaks in the audio. This will maximize the signal to noise ratio of

the system with full modulation.

4) If the unit was set up in Standby Mode, it will be necessary to turn the trans‑

mitter off, then power it up again in normal operation so the RF output will

be on. Then the other components in the sound or recording system can be

adjusted.

www.lectrosonics.com 9

PH (phantom power supply)

The transmitter input jack can provide phantom power for the attached mi‑

crophone if needed, with voltages at 5, 15 or 48 or be turned off. Use the UP

and DOWN arrow buttons to select the desired setting. Phantom power will

consume a slight amount of battery power.

About the Phantom Power Supply

Three phantom voltages are selectable from the control panel.

The voltages are:

• 5 Volts for lavaliere microphones,

• 15 Volts for some professional mics requiring high current and for many

common stage mics that will operate over a wide phantom Voltage range of

12 to 48 Volts. With the proper adapter, this position can also be used with

T power microphones. See our web site for details on ﬁnding or making the

proper adapter.

• 48 Volts for microphones that do in fact require a supply greater than 18

Volts. (See below for a discussion of why 42 and not a “true” 48 Volts.)

For longest battery life use the minimum phantom voltage necessary for the

microphone. Many stage microphones regulate the 48 Volts down to 10 Volts

internally anyway, so you might as well use the 15 Volt setting and save some

battery power. If you are not using a microphone for the input device, or are

using a microphone that does not require phantom power, turn the phantom

power off.

Phantom power should only be used with a fully ﬂoating, balanced device

such as most microphones with a 3‑pin XLR connector. If you use the phan‑

tom power with an unbalanced device or if pins 2 or 3 are DC connected to

ground, then you will draw maximum current from the power supply. The HM

is fully protected against such shorts but the batteries will be drained at twice

the normal rate.

The transmitter can supply 4 mA at 42 Volts, 8 mA at 15 Volts, and 8 mA at 5

Volts. The 42 Volts setting actually supplies the same voltage to a 48 Volt mi‑

crophone as the DIN standard arrangement due to a dynamic biasing scheme

that does not have as much voltage drop as the DIN standard. The 48 Volt

DIN standard arrangement protects against shorts and high fault current with

high resistance in the power supply feeds to pins 2 and 3. This provides pro‑

tection if the supply current is accidentally shorted to ground and also keeps

the microphone from being attenuated by the power supply.

The HMa improves on those functions and is able to use less power from

the battery by using constant current sources and current limiters. With this

dynamic arrangement the HMa can also supply more than twice the current

of competing 48 Volt plug on units and provide four times the current for some

very high end 15 Volt microphones.

LECTROSONICS, INC.10

FREQ Button

The operating frequency can be adjusted according to the frequency in MHz

or a two‑digit hexadecimal code. Press the button repeatedly to switch be‑

tween the two displays. The display switches when the button is ﬁrst pushed;

push and hold the button in the desired mode and use the UP and DOWN

arrow buttons to make the adjustment.

Hex code numbering came about years ago when the ﬁrst synthesized wire‑

less equipment was introduced. Two 16‑position rotary switches were used

to set the frequency. 16 on one switch and 16 on the other switch yielded 256

frequencies (16x16=256). While there are no 941 band models that use these

switches, hex code numbering is easier way to remember than frequencies

expressed in MHz with six numerals.

In this example, the same frequency is displayed in MHz and the equivalent

hex code.

The hex code is a hexadecimal numbering sequence that progresses upward

from lowest to highest frequency using the numerals and letters from 0

through F. When the frequency is on a 100 kHz step, the hex code will display

two 00’s for the last two digits, which is easy to remember (3A in the example

above). When the step size is set to 25 kHz, the last two digits will be 00, 25,

50 or 75 (3A.25 in the example below), which is still easier to remember than

all six numerals of the frequency in MHz.

Otros manuales para HMA-941 Series

Tabla de contenidos

Otros manuales de Transmisor de Lectrosonics

Lectrosonics

Lectrosonics WM/E01 Manual de usuario

Lectrosonics

Lectrosonics UM400a Manual de usuario

Lectrosonics

Lectrosonics LM Manual de usuario

Lectrosonics

Lectrosonics Digital Hybrid Wireless SSM Manual de usuario

Lectrosonics

Lectrosonics duet DCHT Manual de usuario

Lectrosonics

Lectrosonics HH Manual de usuario

Lectrosonics

Lectrosonics M2T/ND Manual de usuario

Lectrosonics

Lectrosonics UT200 Manual de usuario

Lectrosonics

Lectrosonics UM450V Manual de usuario

Lectrosonics

Lectrosonics SSM Manual de usuario

Lectrosonics

Lectrosonics UH400A Manual de usuario

Lectrosonics

Lectrosonics DHu Manual de usuario

Lectrosonics

Lectrosonics MM400 Manual de usuario

Lectrosonics

Lectrosonics SM Series Manual de usuario

Lectrosonics

Lectrosonics UM195B Manual de usuario

Lectrosonics

Lectrosonics T5 Manual de usuario

Lectrosonics

Lectrosonics HM Manual de usuario

Lectrosonics

Lectrosonics M175 Manual de usuario

Lectrosonics

Lectrosonics LT Manual de usuario

Lectrosonics

Lectrosonics SM Manual de usuario

Lectrosonics

Lectrosonics DCHT Manual de usuario

Lectrosonics

Lectrosonics UT Manual de usuario

Lectrosonics

Lectrosonics UM400a Manual de usuario

Lectrosonics

Lectrosonics DHu Manual de usuario

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario