Laserworld CS-500 RGY Manual de usuario

CS-500RGY

USER MANUAL

Please read this manual carefully before use!

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

Table of contents

Page

1. SAFETY INSTRUCTIONS 3

. OPERATING DETERMINATIONS 4

3. PACKAGE LIST 4

4. PRODUCT INTRODUCTION 5

5. FUNCTION INTRODUCTION 5

6. INSTRUCTIONS 5

7. CHANNEL’S FUNCTION 6

8. SIGNAL CONNECTION AND ADRESS DIALING 7

9. SAFETY MARKS 8

10. MAINTENANCE 9

11. TECHNICAL SPECIFICATIONS 9

hecking Parts

Please check if the following parts are included:

1 x CS-500RGY Laser

1 x Power cable

1 x User manual

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

DANGER LASER RADIATION!

Avoid direct eye exposure!

Laser radiation can cause eye damage and/or skin damage

All protective measures for a safe operation of this laser must be applied.

1. SAFETY INSTRU TIONS

- If the device has been exposed to drastic temperature fluctuation, do not

switch it on immediately. The arising condensation water might damage your

device. Leave the device switched off until it has reached room temperature.

1. The laser must only be used for shows. The operation is only allowed if it is

controlled by a skilled and well-trained operator.

- Never leave this device running unattended and keep it away from children

and unauthorized persons.

. Keep away from heaters and other heating sources. In order to safeguard

sufficient ventilation, leave 50 cm of free space around the device.

3. Never direct the laser beam to people or animals.

4. CAUTION LASER DIODE: Never unscrew the housing!

There are no serviceable parts inside the device. Maintenance and service

operations shall only be carried out by authorized dealers.

5. Always disconnect from the mains when the device is not in use or before

cleaning it.

- HEALTH HAZARD! Never look directly into the light source, as

sensitive persons may suffer an epileptic shock!

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

2. OPERATING DETERMINATIONS

6. The operator has to make sure that laser radiation – also reflected laser

radiation –higher than the highest allowed level is avoided by technical or

organisational measures.

7. Make sure that the used voltage is : AC 0V~ 40V, 50/60Hz

8. If the device is used in a flying installation, the mounting brackets and an

appropriate safety-rope must be fixed.

9. Laser effects are not designed for permanent operation. Consistent operation

breaks will ensure that the device will serve you for a long time without

defects.

10.In some countries, the operator must notify the accidence insurance and the

authority for industrial safety, before operating a laser. For more information,

contact the relevant authorities.

11.Please consider that unauthorized modifications on the device are forbidden

due to safety reasons!

1 .If this device will be operated in any way differently than described in this

manual, the product may suffer damages and the guarantee becomes void.

Furthermore, any other operation may lead to dangers like short-circuit,

burns, electric shock, etc.

Thank you for using the lub series RGY laser projector. For the sake of

safety and better Operation of this projector, please read this manual

carefully before use and operate the projector , lest incur any personal

injury or damage to the projector.

3. PA KAGE LIST

When you unpack the case, please take time to examine the items as follow:

projector 1

Power cord 1

Owner’s manual 1

projector sling 1

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

4. PRODU T INTRODU TION

The RGY series projector adopts the latest appearance design to make it compact

and light. The housing use imported paint.

The scanning System is vibratory mirror, DMX-51 Signal 10 channels, international

Standard DMX-51 Signal control. It can printing laser pattern at the same time.

There are 1 8 latest laser effect patterns in it, can be used for word (Chinese,

English and Japanese)performance^ animation performance^ laser beam

performance, with spatial, projection and animation effects.

Control modes: DMX-51 Signal control, music control „

RGY series laser projector was applied for the place of public entertainment such as

disco, night club and theater etc.

5. FUN TION INTRODU TION

RGY series laser performer has the powerful performance functions. Abundance laser

patterns and single color or double colors orthree colors laser performance will bring

you a new sensations, it will be more comfortable and convenient for your using. It

has 10 DMX-51 control Signal control, it can make tunnel effect and animation,

geometric, character and 3D effects, Laser sky effects, Rolling effects, Scanning

effects, and Laser tunnel effects in all directions. And it also has music control. The

effect can be control by music rhythm.

Laser module is semiconductor generator, laser wavelength are 53 nm/green and

650nm/red, the two different laser module are combined to give off the yellow laser

light. The laser light source has a long life span and highly stability, complying with

the international Standard.

6. INSTRU TIONS

After unpacking, check whether the projector has been damaged by transport such

as any screw loosening, reflecting mirror broken, etc. If everything is OK, select a

proper location, hang the projector and adjust its angle properly, then connect the

power cord and the ground wire before switch on at the means. Notice that while

using this projector the green and yellow wire has to connect the ground properly by

Professionals. Please examine the electrics and voltage before power on it. We

suggest customer apply 0V or a transformer. 0 seconds after powered on the

projector, it will self-check and then can be used.

Because of the radiate laser generator 's own characteristic, please terminate it for

10 minutes after using it for 30 minutes to secure the laser 's long life span.

Avoid being interfered by other Signals while using the DMX-51 signal contnoller.

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

7. HANNEL’S FUN TION

Channel

DMX

51 Value

0~ 55

Descriptions

0 Close

1~103 Automatic

CH1 Operation

method

104~ 55

Music-active

CH Laser pattern

selection

0~ 55

1 8 Laser patterns

0~1 7

Rotation angle adjustment CHS Laser pattern

rotation

1 8~ 55

Rotation speed adjustment

0~1 7

Adjustment of up/down

turning

angle

CH4 Laser pattern

up/down

1 8~ 55

Adjustment of up/down turning

speed

0~1 7

Adjustment of left/night turning

angle

CHS Pattern

left/right

1 8~ 55

Adjustment of left/right turning

speed

0~1 7

Adjustment of left /right moving

angle

CH6 Pattern moving

1 8~ 55

Adjustment of left /right moving

angle

CH7 Pattern

gradual

0~ 55

Adjustment of pattern gradual

drawing speed

CHS Pattern

point

adjustment

0~ 55

Adjust the definition of pattern

point

0~31

Yellow, red, green

3 ~63

Yellow, red

64-95

Yellow, green

96-1 7 Red> green

1 8-159

Red

160-191

Green

CH9

Select the

pattern color

19 - 55

Yellow

CH10

Select the length

of the color

0- 55

Adding one color node by every

16 values of the DMX value

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

8. SIGNAL ONNE TION AND ADRESS DIALING

When the Controller transmits DMX51 Standard Signals, the connection of which is

accomplished through the "input" and "output" 3-pin XLR socket. When a console

Signal Outputs to the unit, it must correspond to the Pin 1 Ground, Pin Negative

and Pin 3 Positive of the XLR socket on the unit. If it does not work just try

exchanging the Pin and Pin 3 (these pins are generally do not need exchanged

for consoles). The Signal wire length should not exceed 100m in order to avoid the

interference of the other Signals by any other electric appliances.

If your DMX-51 signal Controller adopt 5 pins XLR plug, you need one transfer line,

the transfer method as following:

When control Signals from the console inputs into RGY series projector. The

projector must be assigned a data start address code, so that a unit may act on the

corresponding control Signal. Thus, when any Controller is used, every unit must

have its own data start address Accordingly, the address of the first unit is set as 1,

the second unit has also 10 channels, so its address code is 11, the third unit is set

at 1, so on and so forth (the setting method will also depend on the specific

console, the above is just for general cases).

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

The details of DMX-512 Signal control mode address switch as follow:

This RGY series projector has controlled by on/off switch address code. 1 to 9 are

the numerical value DMX 51 Signal, 10 is the exchange switch of sound activated

control and DMX51 Signal control.

9. SAFETY MARKS

Before maintenances, please refer to eligible personnel.

Please make sure to switch off the power before Installation or maintenance.

Please do not use power and lasers that do not conform to the current

specifications.

Please do not see the laser light directly, in case it might damage the eyes.

Avoid electric shock! Bulb overheating;

Do not use any power voltage and light type of different specifications

Do not expose to the laser light outside.

Do not use it trequently under the humid atmosphere.

Keep the reflecting mirror clean and dry.

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

10. MAINTENAN E

Maintenance should be performed every 15-day period, by using a sponge which is

dipped with alcohol, rather than wet cloth or other chemical liquid, to clean the

mirror.

Always disconnect from the mains when the device is not in use or before cleaning it.

There are no serviceable parts inside the device. Maintenance and service operations

are only to be carried out by authorized dealers.

Never look directly into the light source.

Always disconnect from the mains when the device is not in use or before

cleaning it.

11. TE HNI AL SPE IFI ATIONS

Power supply: AC 110V/AC 0V, 50/60 Hz

DMX 512: 10 channels

ondition temperature: -10°C ~ +35°C

Operating Environment: indoor

Signal input power: -5V~+5V

Power consumption: 150W

Working mode: Live Play @ Music (Sound Programme), ILDA

Optical power: ca. 500mW RGY

Green: ca. 150mW / 53 nm; Red: ca. 350mW / 650nm

Laser classification: 4

Weight: 16 kg

Dimensions: 560 x 410 x 30 mm (L x W x H)

PLEASE NOTE

This device has left our premises in absolutely perfect condition. In order to maintain

this condition and to ensure a safe operation, it is absolutely necessary for the user

to follow the safety instructions and warning notes written in this user manual.

Laserworld cannot be made liable for damages caused by incorrect installations and

unskilled operation!

USER MANUAL: Laserworld Proline CS-500RGY

Date: 01/ 008

Page

EU- Declaration of onformity

We hereby confirm that the following device

Laserworld lub S-500RGY Laser Projector

complies with the essential safety requirements, laid down in the regulations of the

committee to assimilate the provisions of law of all participating EU states on the

electromagnetic compatibility (89/446/EWG).

The device has been classified considering the following EU-norms on

electromagnetic compatibility:

DIN EN 55103-1: 1996

DIN EN 55103- : 1996

DIN EN 61000-3- : 000 + A : 005

DIN EN 61000-3-3:1995 + A1: 001

Assessment of compliance of the product with the requirements relating to the Low Voltage

Directive (LVD) was based on the following standards:

DIN EN 60065 : 00

Furthermore, the device is verified in correspondence to the laser class

regulations DIN EN 608 5-1, if properly set up according to the upper

mentioned laser safety regulation.

After installing the device, an inspection and official approval is indispensable for the overall

setup. The inspection must follow the European guidelines EN 608 5-1 and corresponding

regulations for the prevention of accidents BGV-B . This declaration is executed on behalf of

the CS-500RGY Laser manufacturer

Laserworld (Switzerland) AG

c/o LOG.ON GmbH

Raiffeisenstrasse 8

78658 Zimmern ob Rottweil

GERMANY

VAT number: DE252331844

WEEE-Reg.-Nr.: DE 93014361

Laserworld (Switzerland) AG

based in:

Rheinblick Residenz

Oberstrasse 1

8274 Tägerwilen

SWITZERLAND

Authorized person:

Supervisory board Ms Rhea Gössel

place of business: 8274 Tägerwilen / Schweiz

company number: CH-440.3.020.548-6

Commercial Registry Kanton Thurgau

www.laserworld.com

[email protected]

Otros manuales para CS-500 RGY

Tabla de contenidos

Otros manuales de Equipo de iluminación de Laserworld

Laserworld

Laserworld LW-80k Manual de usuario

Laserworld

Laserworld EL 200 LED Manual de usuario

Laserworld

Laserworld RS 800 G Manual de usuario

Laserworld

Laserworld PRO-200G Manual de usuario

Laserworld

Laserworld GREEN-20000 Manual de usuario

Laserworld

Laserworld BLUE-1300-445 Manual de usuario

Laserworld

Laserworld PL-5000G Manual de usuario

Laserworld

Laserworld PL-16.000RGB Manual de usuario

Laserworld

Laserworld Evolution ES-800RGB Manual de usuario

Laserworld

Laserworld GREEN-300 Manual de usuario

Laserworld

Laserworld CS-200RGY Manual de usuario

Laserworld

Laserworld EL-200 RGY Manual de usuario

Laserworld

Laserworld RS 800 G US Manual de usuario

Laserworld

Laserworld FX Series Manual de usuario

Laserworld

Laserworld CS-8000RGB FX MK2 Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld Garden Series Manual de usuario

Laserworld

Laserworld GREEN-8000C Manual de usuario

Laserworld

Laserworld RB-1.5 Manual de usuario

Laserworld

Laserworld Proline Series Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld Pro-3500RGB Manual de usuario

Laserworld

Laserworld BLUE-1500-445 F Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

Silvair

Silvair MESH-CEDRP Manual de usuario