Laserworld BeamBar 10R-638 Manual de usuario

Manual / Bedienungsanleitung /

Mode d´emploi

Laserworld BeamBar 10R-638

Laserworld BeamBar 10G-532

Laserworld BeamBar 10B-450

Laserworld BeamBar 10RGB

Please spend a few minutes to read this manual fully

before operating this laser!

Bitte lesen Sie diese Bedienungsanleitung sorgfältig

vor Inbetriebnahme dieses Showlasersystems!

Avant d’utiliser cet appareil pour la première fois nous vous recommandons

de lire cette notice d’utilisation!

05/2019

English

Deutsch

Français

Manual: BeamBar Series

page 2 / 29

Rechtlicher Hinweis:

Die Firma Laserworld (Switzerland) AG behält sich das Recht vor, Änderungen an ihren Pro-

dukten vorzunehmen, die der technischen Weiterentwicklung dienen. Diese Änderungen

werden nicht notwendigerweise in jedem Einzelfall dokumentiert.

Diese Betriebsanleitung und die darin enthaltenen Informationen wurden mit der gebotenen

Sorgfalt zusammengestellt. Die Firma Laserworld (Switzerland) AG übernimmt jedoch keine

Gewähr für Druckfehler, andere Fehler oder daraus entstehende Schäden.

Die in dieser Bedienungsanleitung genannten Marken und Produktnamen sindWarenzeichen

oder eingetragene Warenzeichen der jeweiligen Titelhalter.

Legal notice:

Thank you for purchasing this Laserworld product. Due to continual product developments

and technical improvements, Laserworld (Switzerland) AG reserves the right to make modi-

cations to its products.

This manual and its content have been made with due care but Laserworld (Switzerland) AG

cannot however, take any responsibility for any errors, omissions or any resulting damages

forthwith.

The brands and product names mentioned in this manual are trade marks or registered trade

marks of their respective owners.

Information juridique :

L’entreprise Laserworld (Switzerland) AG se réserve le droit d’eectuer des modications con-

cernant leurs produits et ainsi de répondre au développement technique. Ces modications

ne seront pas nécessairement annoncées en tout cas spécique. Ce mode d’emploi et les in-

formations contenues dedans ont été établis avec le soin minutieux qui s’impose dans ce cas.

Laserworld (Switzerland) AG ne pourra pas être tenue responsable pour d’éventuelles erreurs

d’impression ou dommages en résultants.

En cas de doutes, veuillez toujours contacter Laserworld (Switzerland) AG . Les noms de

marques et de produits utilisés dans ce mode d’emploi sont des marques de fabrique ou des

marques déposées.

L’utilisation est réservée à un usage professionnel selon décret n°2007-665 du 2 mai

2007 relatif à la sécurité des appareils à laser sortant!

Article 4 bis :

« Les usages spéciques autorisés pour les appareils à laser sortant d’une classe supérieure à 2

sont les usages professionnels suivants :

(…)

9° Spectacle et achage :

Toutes les applications de trajectoire, de visualisation, de projection ou de reproduction

d’images en deux ou trois dimensions. »

Manual: BeamBar Series

page 3 / 29

Content:

1. Product and package contents

2. Preliminary warning notes

3. Initial operations, safety instructions

4. Working on the device

5. Service notes

6. Warnings and other notices on the device

7. Device connections

8. Operation

Final statement

Technical data sheet

Specications

Manual: BeamBar Series

page 4 / 29

1. Product and package contents

Please check if all listed parts are included and undamaged. Included in delivery:

1 x BeamBar 1 x Interlock connector 1 x Manual

1 x Power cable 2 x Keys for key switch

3. Initial operations, safety instructions

1. Make sure to use correct voltage; see in-

formation on device & in this manual.

2. Make sure that the device is not connec-

ted to mains during installation.

3. Installation has to be done by technical

experienced and qualied persons ac-

cording to safety regulations of the res-

pective country.

4. Always ensure that maximum permissi-

ble exposure (MPE) is not exceeded in

areas accessible to the public or mem-

bers of sta.

5. In some countries an additional ins-

pection by technical control institutes

could be necessary.

6. Connect an easily accessible inter-

lock connector or circuit breaker

to the projector.

7. The power supply should be easily acces-

sible.

8. When installing the laser mount it with

a minimum distance of 15 cm from walls

and objects.

9. For safe setup e.g. on walls or ceilings

please use a safety cord. The safety cord

should be able to withstand tenfold the

weight of the device. Please follow the

accident prevention regulations of pro-

fessional associations and/or comparable

regulations for accident prevention.

10. If the device has been exposed to great

temperature changes, do not switch it

on immediately. Condensation (or any

moisture/water formed) may damage

device.

2. Preliminary warning notices

1. Please use this device only according to these operating instructions.

2. Do not use the device if there are any visible damages on housing, connector panels,

power supplies or power cords.

3. Never look directly into the light source of a laser projector. Danger of damage to the

eyes or even blindness in extreme circumstances!

4. This device must not be permanently connected to mains. Disconnect it from mains or use

the power button to switch if o if not in use.

4. Do not operate the device at high humidity or in the rain or in dusty environments.

5. Protect device against dripping or splashing water. Do not place any liquid lled

containers near to this device.

Any warranty claims are void if the warranty label is removed or tampered

with in any way.

Manual: BeamBar Series

page 5 / 29

11. Never use dimmer, RC or other elect-

ronically switched sockets. Whenever

possible, do not use the laser projector

together with large appliances (espe-

cially fog machines) on the same mains!

12. Ensure sucient ventilation and do not

place the device on any warm or heat ra-

diating surface. Especially the ventilati-

on openings must not be covered!

13. Ensure that device does not get over-

heated. Make sure that the device is not

exposed to spotlights (especially moving

heads). Heat of spotlights could overheat

laser in a little while and leads to a degra-

dation of performance.

14. This unit is intended for indoor use only.

4. Working on the device

1. This product has no user serviceable parts inside and should

only be maintained and serviced by a qualied engineer.

2. Be sure that the BeamBar is not connected to the mains

while installing the device.

3. Take o all reecting things like rings, watches, etc.

before starting to work with or at the projector.

4. Only use non-reecting tools to work on device.

5. Wear protective clothing (like goggles, gloves etc.) according to laser power and wave-

length of the laser.

5. Service notes

• Moisture and heat can reduce lifetime of

the laser system dramatically and expires

any warranty claim.

• Quick on/o switching of this device will

reduce durability of the laser diode dra-

matically.

• Avoid sharp knocks and shocks to this

device an endsure sucient protection

during transportation. Look after your La-

serworld product.

• To increase durability of your laser,

protect device against overheating:

-Always ensure sucient ventilation.

-Do not face spotlights (especially mo-

ving heads) to the device.

-Check temperature after approx. 30

minutes with each new installation.

If necessary install the projector at a

place with dierent temperatures.

-Keep the device dry. Protect it from

moisture, rain and damp.

-Switch o device and disconnect it

from mains when it is not needed.

Diodes are switched on and can wear

out even if there is no visible laser

output.

• Please ensure the fans and heatsinks are

clear from dust and debris otherwise the

risk of overheating may occur. If the unit

and airways appear to be blocked then

please contact a qualied service engi-

neer to maintain and service the product.

• Removal of the warranty label as well

as damages to the device caused by

improper handling, neglect of the sa-

fety instructions and service notes will

void the warranty.

Manual: BeamBar Series

page 6 / 29

Laser radiation!

Avoid exposure

to beam.

Laser class 3B

Caution of

radiation if cover

is removed

Power supply

& consumption

Model type

Wavelength

Output power

Production

year

Use in enclosed spaces only!

6. Warnings and other notices on the device

A: Laser Radiation Symbol; B: Caution: laser aperture

DMX in / out

key switch

DMX address/operation mode

Microphone &

Power indicator

Interlock

microphone

sensitivity

power

connection

7. Device connections

Manual: BeamBar Series

page 7 / 29

8. Operation

1. Connect the power cable to the device and then to the mains

2. Insert key and turn it ‚ON‘

3. Please make sure, that the Interlock connector is inserted

4. Select mode:

• Your device runs in auto mode:

• Your device runs in music mode:

Adjust the music-sensitivity with the trim pot at the rear side of the device.

• Use the Master-Slave-Mode:

To use the daisy chain mode, connect two (or more) laser projectors of the same series

via DMX cables:

Master projector (DMX out) -> DMX cable -> slave projector 1 (DMX in) ;

slave projector 1 (DMX out) -> DMX cable -> slave projector 2 (DMX in) ...etc.

If you use the master projector in music mode or in auto mode, set all DIP switches of

every slave projector to o.

If you use the master projector in DMX mode, set DIP switch 1 of every slave projector to

on and every other DIP switch (2-10) to o.

• Your device runs in DMX mode if ‘10‘ is switched o:

Set the DMX address

Connect a DMX controller to operate the laser.

Manual: BeamBar Series

page 8 / 29

Use the switches 1 - 9 to set the DMX address of the laser. Each switch represents a num-

ber.

Switch 12345678910

Number 1 2 4 8 16 32 64 128 256 Mode Switch

The BeamBar uses 13 DMX channels, so make sure that the next device uses an address

that doesn’t overlap with this range.

DMX Control Chart for BeamBar 10R-638, BeamBar 10G-532, BeamBar 10B-450,

BeamBar 10RGB, BeamBar 10B-450 INTENSE

Channel Value Function

1 0-49 laser o

50-99 sound mode

100-149 automatic mode

150-199 DMX mode (Channel 2 --> Channel 3 valid)

200-255 DMX mode (Channel 4 --> Channel 13 valid)

2 0-255 program / eect selection

3 0-255 Speed (fast to slow, 8 levels)

4 0-255 0-9: laser o; 10-255: laser on

5 0-255 0-9: laser o; 10-255: laser on

6 0-255 0-9: laser o; 10-255: laser on

7 0-255 0-9: laser o; 10-255: laser on

8 0-255 0-9: laser o; 10-255: laser on

9 0-255 0-9: laser o; 10-255: laser on

10 0-255 0-9: laser o; 10-255: laser on

11 0-255 0-9: laser o; 10-255: laser on

12 0-255 0-9: laser o; 10-255: laser on

13 0-255 0-9: laser o; 10-255: laser on

Manual: BeamBar Series

page 9 / 29

DMX Control Chart for BeamBar 10RGB-W (requieres 31 DMX-channels)

Channel Value Function

1 0-40 laser o

40-160 automatic mode

160-255 DMX mode

2 0-255 Aperture 1: red intensity

3 0-255 Aperture 1: green intensity

4 0-255 Aperture 1: blue intensity

5 0-255 Aperture 2: red intensity

6 0-255 Aperture 2: green intensity

7 0-255 Aperture 2: blue intensity

8 0-255 Aperture 3: red intensity

9 0-255 Aperture 3: green intensity

10 0-255 Aperture 3: blue intensity

11 0-255 Aperture 4: red intensity

12 0-255 Aperture 4: green intensity

13 0-255 Aperture 4: blue intensity

14 0-255 Aperture 5: red intensity

15 0-255 Aperture 5: green intensity

16 0-255 Aperture 5: blue intensity

17 0-255 Aperture 6: red intensity

18 0-255 Aperture 6: green intensity

19 0-255 Aperture 6: blue intensity

20 0-255 Aperture 7: red intensity

21 0-255 Aperture 7: green intensity

22 0-255 Aperture 7: blue intensity

23 0-255 Aperture 8: red intensity

24 0-255 Aperture 8: green intensity

25 0-255 Aperture 8: blue intensity

26 0-255 Aperture 9: red intensity

27 0-255 Aperture 9: green intensity

28 0-255 Aperture 9: blue intensity

29 0-255 Aperture 10: red intensity

30 0-255 Aperture 10: green intensity

31 0-255 Aperture 10: blue intensity

5. To turn o the device turn key switch o („OFF“) and disconnect the power cable from

the mains.

Manual: BeamBar Series

page 10 / 29

Final statement

Laserworld products are tested and product packaging is inspected before leaving our

warehouse.

Users must to follow the local safety regulations and warnings within this manual and adhere

to any regulations within its place of use. Damages through inappropriate use will void any

liability or warranty of our products.

Due to continual product developments, please check for the latest update of this product

manual at www.laserworld.com. If you do have any further questions, then please contact

your dealer/place of purchase or use our contact section on our website.

For service issues, please contact your dealer/place of purchase and ensure only genuine

Laserworld spare parts are used in any service repairs.

Errors and Omissions excepted and products are subject to change.

Laserworld (Switzerland) AG

Kreuzlingerstrasse 5

8574 Lengwil

SWITZERLAND

Registered oce:

8574 Lengwil-Oberhofen / Switzerland

Company number: CH-440.3.020.548-6

Commercial Registry Kanton Thurgau

CEO: Martin Werner

VAT no. (Switzerland): 683 180

UID (Switzerland): CHE-113.954.889

VAT no. (Germany): DE 258030001

WEEE-Reg.-No. (Germany): DE 90759352

www.laserworld.com

[email protected]

representative according to EMVG:

Ray Technologies GmbH

Managing Director: Martin Werner

Mühlbachweg 2

83626 Valley / Germany

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Equipo de iluminación de Laserworld

Laserworld

Laserworld CS-8000RGB FX MK2 Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Laserworld

Laserworld LED-54 Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld CS-400G Manual de usuario

Laserworld

Laserworld BLUE-1300-445 Manual de usuario

Laserworld

Laserworld GREEN-150E Manual de usuario

Laserworld

Laserworld GREEN-150A Manual de usuario

Laserworld

Laserworld RED-5000-640 Manual de usuario

Laserworld

Laserworld PRO-7000R/640 Manual de usuario

Laserworld

Laserworld EL-50G DMX Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld SwissLas Purelight Series Manual de usuario

Laserworld

Laserworld PL-5000G Manual de usuario

Laserworld

Laserworld Ecoline Series Manual de usuario

Laserworld

Laserworld GREEN-75E Manual de usuario

Laserworld

Laserworld PL-4500 RGB US Manual de usuario

Laserworld

Laserworld EL-200S DMX Manual de usuario

Laserworld

Laserworld Club Series Manual de usuario

Laserworld

Laserworld DISCO-300G Manual de usuario

Laserworld

Laserworld EL-120 R Manual de usuario

Laserworld

Laserworld PL-4000RGB Manual de usuario

Laserworld

Laserworld Garden Series Manual de usuario

Laserworld

Laserworld GREEN-150 Manual de usuario

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario

Silvair

Silvair MESH-CEDRP Manual de usuario