Larson Electronics EPL-BS-70LED-6XMB-150X12 Manual

EPL-BS-70LED-6XMB-150X12

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

70 Watt Low Voltage Portable Explosion Proof LED Light

Magnetic Base - 150' SOOW Cord

Instruction Guide

Thank you for your purchase of the Larson Electronics EPL-BS-70LED series light. This light is completely assembled,

tested and ready for use when shipped from the factory. Please follow the steps below in order to operate and maintain

this product.

IMPORTANT

READ CAREFULLY BEFORE OPERATING THIS LIGHT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF UNSURE

ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL. THE EPL-BS-70LED

MUST BE OPERATED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER

GROUNDING IS REQUIRED FOR SAFETY.

FOR PERSONAL SAFETY, ALWAYS CONFIRM THE RATING OF ANY KNOWN HAZARDOUS OR POTENTIALLY HAZARDOUS

LOCATION WHERE THE LIGHT IS TO BE USED.

WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT LABEL.

WARNING: TO PREVENT IGNITION OF A HAZARDOUS ATMOSPHERE, THE SUPPLY CIRCUIT SHOULD BE DISCONNECTED

WHEN INSTALLING OR PERFORMING ANY MAINTENANCE ON THIS UNIT.

WARNING: WHEN INSTALLING THIS LIGHT IN HAZARDOUS LOCATIONS, CHECK THE OPERATING TEMPERATURE LIMITS

PRIOR TO INSTALLATION TO BE SURE IT CONFIRMS TO THE ENVIRONMENTAL TEMPERATURE RESTRICTIONS AND NEC

CLASSIFICATIONS. CHECK THE FIXTURE’S METAL NAMEPLATE FOR TEMPERATURE (T) RATINGS.

WARNING: DO NOT SCRATCH OR CHIP THE FRONT LENS. TURN THE POWER OFF BEFORE STARTING INSTALLATION OR

REPAIR.

WARNING: OPERATE THIS FIXTURE ONLY AT THE VOLTAGE OF YOUR SPECIFIC SUPPLY CIRCUIT. FAILURE TO DO SO

WILL RESULT IN DAMAGE TO THE FIXTURE.

WARNING: SUBSTITUTE COMPONENTS MAY IMPAIR EXPLOSION PROOF SAFETY.

INSTALLATION

Before operation, confirm that the power source will provide the

correct voltage indicated on the product nameplate. Ensure the

receptacle will accept the cord cap attached to the light.

Check product nameplate for Ratings and Approvals.

Place the light in the desired location and run its power cord to a

power source. Ensure all safety requirements are followed for the

hazardous area.

WARNING: Transformer MUST remain OUTSIDE Hazardous Area!

This light is instant-on and will illuminate once energized.

Multi-voltage capability allows this light to be powered via

Voltage to Transformer: 110-277V AC 50/60Hz

ADJUSTMENT

Loosen the hand screw on side of the light to make vertical adjustments. Tighten hand screw once desired angle is

achieved.

The light can be mounted in any direction to a sturdy metallic surface. Ensure the mounting surface can withstand the

weight.

When removing, pull light straight off. Do not drag the magnets as this could scratch the surface light is mounted to.

Use the handle on top for easy maneuverability.

EPL-BS-70LED-6XMB-150X12

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

MAINTENANCE

1. Perform visual, electrical, and mechanical inspections on a regular basis. The environment and frequency of use

should determine this. However, it is recommended that checks be made at least once a year. We recommend an

Electrical Preventive Maintenance Program as described in the National Fire

2. Protection Association Bulletin NFPA No. 70B: Recommended Practice For Electrical Equipment Maintenance

(www.nfpa.org).

3. The lens should be cleaned periodically to ensure continued lighting performance. To clean, wipe the lens with a

clean, damp cloth. If this is not sufficient, use a mild soap or a liquid cleaner such as Collinite NCF or Duco #7. Do

not use an abrasive, strong alkaline, or acid cleaner. Damage may result.

4. Visually check for undue heating evidenced by discoloration of wires or other components, damaged parts, or

leakage evidenced by water or corrosion in the interior. Replace all worn, damaged, or malfunctioning components,

and clean gasket seals before putting the luminaire back into service.

5. Electrically check to make sure that all connections are clean and tight.

6. Mechanically check that all parts are properly assembled.

TROUBLESHOOTING

Refer to the guide below or contact the manufacturer if the fixture does not function properly.

Is the correct line voltage being supplied to the fixture?

Is the fixture properly grounded?

Make sure installed power switch is functioning properly (if applicable).

These instructions may not cover all details or variations of this product for your equipment or installation requirements.

Should further information not covered by these instructions be required, please contact Larson Electronics at

1-800-369-6671 for further assistance.

Please visit LarsonElectronics.com for Warranty and Return information.

Tabla de contenidos

Otros manuales de Luz de trabajo de Larson Electronics

Larson Electronics

Larson Electronics RL-85-LED-36W-CPR Manual de usuario

Larson Electronics

Larson Electronics EHL-LED-240X12V-50 Manual de usuario

Larson Electronics

Larson Electronics EPL-QC-16C-2X50LED-RT-100 Manual de usuario

Larson Electronics

Larson Electronics L810 Manual de usuario

Larson Electronics

Larson Electronics LEDWP-250E-DLC-5000K Manual

Larson Electronics

Larson Electronics EPL-QC-16C-2X50LED-RT-X12V-C1D1-12.3-100-EPP Manual de usuario

Larson Electronics

Larson Electronics GL-9900 Manual

Larson Electronics

Larson Electronics WAL-TP.S-2XRL16-LED Manual de usuario

Larson Electronics

Larson Electronics EPL-PM-150LED-X24I-100 Manual

Larson Electronics

Larson Electronics EPL-BS-25WRE Manual

Larson Electronics

Larson Electronics EPL-16C-1MLED-300 Manual de usuario

Larson Electronics

Larson Electronics WDL-12-IPS-LED-1227 Manual de usuario

Larson Electronics

Larson Electronics WAL-SBDL-WP60E-XX-1227 Manual de usuario

Larson Electronics

Larson Electronics LED10W-1X2LT Manual de usuario

Larson Electronics

Larson Electronics EHL-LED-15W-50-HR Manual de usuario

Larson Electronics

Larson Electronics WAL-BP-3XLED-CPR Manual de usuario

Larson Electronics

Larson Electronics GNM-LEDWL-25W Manual

Larson Electronics

Larson Electronics RSLED Manual de usuario

Larson Electronics

Larson Electronics WAL-WBC-500LTL-LED-100 Manual de usuario

Larson Electronics

Larson Electronics EXPRL-98 Manual de usuario

Larson Electronics

Larson Electronics EPL-QC-16C-2X50LED-RT-X24V-C1D1-12.3-100-EPP Manual de usuario

Larson Electronics

Larson Electronics WL-LED-12-M Manual de usuario

Larson Electronics

Larson Electronics WAL-DL-60LED-M-GCR50-SP0002 Manual de usuario

Larson Electronics

Larson Electronics AML-LED-WP40-M-22C Manual

Manuales populares de Luz de trabajo de otras marcas

ANSMANN

ANSMANN POWERLIGHT 5.1 Manual de usuario

RTRMAX

RTRMAX RTX1868 Manual de usuario

FeinTech

FeinTech LAL00220 Manual de usuario

Bunker Hill Security

Bunker Hill Security 64735 Manual de usuario

Goobay

Goobay 30450 Manual de usuario

REV Ritter

REV Ritter SPOT Manual de usuario

Ignition

Ignition Stagepix Line 100 IP Manual de usuario

SCANGRIP

SCANGRIP DUO CONNECT Manual de usuario

Bosch

Bosch GLI 18 V Manual de usuario

Bayco

Bayco SL-1514 Manual de usuario

EUFAB

EUFAB SMD LED 8+1 Manual de usuario

DeWalt

DeWalt DCL510 Manual de usuario

PowerSmith

PowerSmith PWLD080T Manual de usuario

MaxLite

MaxLite 73683 Manual de usuario

Heitronic

Heitronic Trend 27867 Manual de usuario

Monzana

Monzana Gore MZCL10 Manual de usuario

EINHELL

EINHELL TE-CL 18/2000 LiAC Manual de usuario

Bayco

Bayco NIGHTSTICK Dual-Light Xtreme Lumens... Manual de usuario