Larson Electronics EPS-3PSW-MMS Manual de usuario

EPS-3PSW-MMS

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

The Larson Electronics EPS-3PSW-MMS Explosion Proof Factory Sealed 3-Position Selector Switch is suitable for

preventing the ignition of external, flammable atmospheres in hazardous locations. This unit features the following

classified ratings: Class I, Division 1 & 2 (Groups C, D); Class II, Division 1 (Groups E, F, G); Class II Division 2

Groups F & G and Class III. The explosion proof switch comes with a 600V AC voltage rating and a weatherproof

build. When purchasing this product, please choose between 1/2" or 3/4" NPT hub sizes and feed thru/dead end

options.

WARNING: To avoid risk of explosion, all flat machined surfaces must be kept clean and free from scratches,

dents, debris, paint, and corrosion. The flat machined surfaces are explosion proof joints, and must be clean and

undamaged on both the enclosure and cover.

1. Do not use this equipment other than the intended use as specified on the equipment nameplate.

2. Turn OFF the supplying circuit before beginning installation or performing any maintenance.

3. Service should be performed by qualified service personnel.

4. All installations must comply with the applicable local and/or National Electrical Code. (Note: In the

orientation of the enclosure (box & cover), the “TOP” is considered to be at the location of the cast-in part

numbers.)

INSTALLATION

1. The surfaces of the flat ground joint are precision machined to insure an explosion proof joint and must

be protected from scratches or damage during installation.

2. When switch is mounted in the enclosure, it must be mounted to agree with cover indication of operation.

That is, when the cover indicates ON, the switch must be in the ON condition.

3. Before the cover is installed, the flat ground joint surface must be thoroughly wiped clean of any dirt, grit, or

other foreign substances and a light thin coating of lubricant placed on the joint to prevent possible

corrosion.

The joint between the box and the cover has been made accurately to .0015” to prevent the passage of

this accuracy is destroyed.

4. ALL cover screws must be installed with at least five full threads engaged and must be securely tightened.

All cover openings must be closed with a suitable cover.

5. Gaskets must not be added to these devices. Only gaskets designed for and permanently installed

in these devices may be used.

6. In accordance with the hazardous location information specifying Class and Group listing marked on the

device, sealing fittings must be added that will comply with requirements in the latest issue of the Canadian

Electrical Code or National Electrical Code and any special requirements that are stated in the instruction

sheet with the enclosure.

MAINTENANCE

Before removing the cover from any such device for inspection or maintenance, the power supply circuit must be

OFF.

WARNING: To prevent risk of explosion, hammers and prying tools must not be used to remove covers off

enclosures. Damage to the explosion proof flat machined surfaces on cover and enclosure may result. Handle

covers carefully. Do not place them on surfaces that might damage or scratch the flat machined surfaces.

Before replacing the cover, after it has once been removed, the flat ground joint surfaces must be cleaned

as described in step 3 under installation.

WARNING: To prevent risk of explosion, replace devices if the flat machined surface is damaged, scratched,

dented, or corroded. Field rework of flat machined surfaces is not possible.

The field wiring terminals on the switch units used for pushbutton or selector switch stations are marked. The

and “0” indicate normally open contacts; and and “C” indicate normally closed contacts of the switch. These

switches are provided with binding screw terminals. For EDS/EDSC Series Toggle Switches: splice factory sealed

wires to supply wires using suitable connectors.

1. Terminate incoming cables to the line and load side of switch (field installation only).

2. Strip the insulation on each conductor wire back 3/8”.

3. Use a slotted or Phillips head screwdriver to loosen the field wiring terminal screws the required three (3) or four

(4) turns.

4. Insert the bare wire conductor(s) on either side of the terminal screw(s), under the terminal wire clamp(s) and

securely tighten the screw(s).

5. NOTE: Do not exceed 15 in.-lbs. of torque.

6. Test wiring for correctness with continuity checks and also for unwanted grounds with an insulation resistance

tester.

WARNING

No conduit openings are to be added in the field. All unused conduit openings must be plugged and plugs must be a

minimum of 1/8 inch thick and have a minimum of five (5) threads engagement (seven (7) threads for Group B

applications). For EFS Enclosures with 1 inch hub(s), EDS 3-pole Snap Switches and EFD/EDS with “GB” suffix, all

conduits must be sealed within 18 in. of the enclosure.

7. Assemble cover on box making certain there are no pinched wires.

8. Assemble cover to the device body with the cover screws making certain there are no pinched wires. Check the

tightness of the cover screws to ensure that the cover assembly is securely fastened.

9. Pour Chico® Sealing Compound into EYS/EYD Series Sealing Fittings (where used) in accordance with the

instructions with each sealing fitting used. (NOTE: Seals are not required for Class I, Division 2.)

10. Tighten cover bolts.

WARNING

Check for dirt, grit or other foreign material on the mating surfaces of the cover and the device body. Be certain that

each surface is wiped completely clean before assembling. Surfaces must seat fully against each other to provide a

proper explosion proof seal.

CAUTION: Use 12 AWG copper conductors only. Insert the bare wire conductor(s) under terminal clamp and

securely tighten the screw(s). Note: Do not exceed 35 in-lbs. of torque.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR

INSTALLATION REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED,

PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671

FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Tabla de contenidos

Otros manuales de Cambiar de Larson Electronics

Larson Electronics

Larson Electronics EPS-2XPB-SG-600V-LKC Manual de usuario

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Manual de usuario

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC Manual de usuario

Larson Electronics

Larson Electronics EPNFDS-MTS-200A-3P Manual de usuario

Larson Electronics

Larson Electronics EPS-FS-B-2PSW Manual de usuario

Larson Electronics

Larson Electronics EPSW-3PH-20 Manual de usuario

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Manual de usuario

Larson Electronics

Larson Electronics EPS-25A-3W Manual de usuario

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Manual de usuario

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT Manual de usuario

Larson Electronics

Larson Electronics EPS-PB20 Manual de usuario

Larson Electronics

Larson Electronics EPSW-30A-WP Manual de usuario

Larson Electronics

Larson Electronics EPCS-PL-2X-RG Manual de usuario

Larson Electronics

Larson Electronics LED-ILS Manual de usuario

Larson Electronics

Larson Electronics EPCS-PB10-1XMPB-3PSW Manual de usuario

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP Manual de usuario

Larson Electronics

Larson Electronics EXP-RT-3PH-MIN.5-208V Manual de usuario

Larson Electronics

Larson Electronics EPS-SW1-ESTP Manual de usuario

Larson Electronics

Larson Electronics EPSW-1PH-20 Manual de usuario

Larson Electronics

Larson Electronics EPS-25A Manual de usuario

Larson Electronics

Larson Electronics LM HZ-EW-SP1097-HV Series Manual de usuario

Larson Electronics

Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Manual de usuario

Larson Electronics

Larson Electronics EPL-SW Series Manual de usuario

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Manual de usuario

Manuales populares de Cambiar de otras marcas

URC

URC Total Control MFS-8 Manual de usuario

Azbil

Azbil HPQ-D11 Manual de usuario

Sony

Sony DFS-900M Manual de usuario

SICK

SICK i17S Manual de usuario

F&F

F&F SZR-277 Manual de usuario

Shure

Shure UAMS/BK Manual de usuario

Dräger

Dräger X-zone Switch Off Manual de usuario

Asco

Asco Joucomatic 349 Series Manual de usuario

BT Mini Hub Manual de usuario

D-Link

D-Link DES-1226G Manual de usuario

Johnson Controls

Johnson Controls FS80-C Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manual de usuario

MicroNet

MicroNet SP1200A Manual de usuario

Ruijie

Ruijie RG-PF2920 Series Manual de instalación y funcionamiento

Altinex

Altinex DA1914SX Manual de usuario

MiLAN

MiLAN MIL-SM2401M Manual de usuario

RJM

RJM MASTERMIND PBC/6X Manual de usuario

Atlas

Atlas MMK-KVM8 Manual de usuario