Larson Electronics LEDWP-500-M-20C Manual de usuario
LEDWP-500-M-20C
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
1 of 2
Magnetic Mount 60 Watt Low Profile LED Flood Light
20' Cord - 120-277V AC
Instruction Manual
Thank you for your purchase of the Larson Electronics LEDWP-500-M-20C.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDWP-500-M-20C MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE
AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING:
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE
CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT
READILY AVAILABLE.
IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO
PERSONNEL.
PERIODIC INSPECTION OF THE CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,
THE CORD MUST BE REPLACED BEFORE RESUMING USE.
Magnetic Warning
•PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE.
ELECTROMAGNETIC FIELDS INCLOSE PROXIMITY TOHEART PACEMAKER COULD CAUSE
PACEMAKER INTERFERENCE OR PACEMAKER FAILURE.
•KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING ASINJURY COULD OCCUR.
The LEDWP-500-M-20C Magnetic Mount LED Flood Light offers high light output from a compact form factor and is designed to provide
a more durable and long lived alternative to halogen and metal halide units. This 60 watt LED light produces a wide flood beam without
the high heat, fragile construction, or high energy costs of incandescent lighting.
LEDWP-500-M-20C
Larson Electronics, LLC
Phone: (800) 369-6671
Fax: (903) 498-3364
www.larsonelectronics.com
2of 2
MOUNTING
The LEDincludes allnecessary hardware for installing the mounting bracket.Follow the guideline below to
properly assemble and install the unit.
The light includes the LEDlight and trunnion mount.Some models may omit hardware depending on selected
options.
1. Begin by choosing a location toinstall the fixture. This LEDiswaterproof, vapor proof, and built to resist
the damaging effects ofan outdoor environment. This fixture should not be used in areas with no ventilation or
extreme ambient temperatures.
2. Affix the mount to your chosen surface. There are pre-drilled holes on the trunnion bracket for mounting and
for the cord grip. These can be used anyway suitable for the location. Plan a way for wiring to connect such as
using a separate junction box and utilize the cord grip where necessary.
3. Attach lamp. The trunnion mount can be attached to the lamp in two locations, the lower area or middle area
on the backofthe wall pack. The fixture can be placed in any direction and is attached using 2 screws and 2
washers.
WIRING
We strongly encourage a licensed electrician install this product, especially in outdoor locations where
weatherproofing may be required. Universal voltage driver permitsoperation at 110V - 277V AC, 50 or 60Hz.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriatelight
fixturewires as shown in the diagram
Secure each pair with a wire nut according to the
diagram. Utilize a junction box or similar device and
take precautionary steps for weatherproofing all
connections if installed in alocation where water may
come in contact with the unit. Ensure the unit is
properly grounded.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The LEDWP-500-M-20C is designed to provide years of reliable performance. Should the need for replacement parts
arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
Tabla de contenidos
Otros manuales de Foco de Larson Electronics
Larson Electronics
Larson Electronics RCL200-RF Manual de usuario
Larson Electronics
Larson Electronics WAL-QP-4X500-25 Manual de usuario
Larson Electronics
Larson Electronics EPLC2-LED-150W-RT-JB2 Manual de usuario
Larson Electronics
Larson Electronics EPL-WPLED-150W-RT-140DB Manual de usuario
Larson Electronics
Larson Electronics EPL-LED-150W-RT-DIMM Manual de usuario
Larson Electronics
Larson Electronics LEDWP-720 Manual de usuario
Larson Electronics
Larson Electronics EPLC2-LED-150W-RT-JB2-25C Manual de usuario
Larson Electronics
Larson Electronics HID-22-SL-480V Manual de usuario
Larson Electronics
Larson Electronics HAL-PRM-150W-LED Manual de usuario
Larson Electronics
Larson Electronics BL24-LED Manual de usuario
Larson Electronics
Larson Electronics RT-100C-XEMG-10C Manual de usuario
Larson Electronics
Larson Electronics GL-4600-F-M-12I Manual
Larson Electronics
Larson Electronics WAL-M-3X48LED-120 Manual de usuario
Larson Electronics
Larson Electronics WAL-QP-2X-25 Manual de usuario
Larson Electronics
Larson Electronics WAL-SM-MHFL-1000W-50C Manual de usuario
Larson Electronics
Larson Electronics LEDWP-LP-450-TRN-DCM Manual de usuario
Larson Electronics
Larson Electronics EPL-LED-150W-RT-20-HDBC Manual de usuario
Larson Electronics
Larson Electronics Golight RadioRay 7901 Manual
Larson Electronics
Larson Electronics LEDEQ-PK-24X2-CPR-SPFL Manual de usuario
Larson Electronics
Larson Electronics Stryker Light Manual
