Lanzar VIBE530P Manual de usuario
5BandParametricEqualizer
with Voltage Meter, Subwoofer Gain Control
and Bass Driver
www.Lanzar.com
2
TABLE OF CONTENTS
1. FEATURES
2. PRECAUTIONS
Installation
3. CONTROLS
4. OPERATIONS
Setting system volume
Adjusting the controls
Setting the low-pass frequency
Connecting an MP3 player or video unit
Care and maintenance
5. INSTALLATION AND WIRING
What's in the Box
Before starting
Tools and additional components
Mounting Diagram
Wiring diagram
6. TROUBLESHOOTING
The unit does not work; no lights
Sound is distorted
No sound coming from the unit
7. GLOSSARY
8. SPECIFICATIONS
3
4
4
5
6
6
6
6
7
7
7
7
8
9
9
10
12
12
12
12
12
13
www.Lanzar.com
3
FEATURES
LANZAR VIBE530P is a 5-band stereo equalizer / crossover specically created for
the mobile environment.
The VIBE530P provides powerful features in a compact size:
• Five equalization bands, each frequency adjustable from -12 to +12dB
(-15 to +15dB for subwoofer frequencies)
• Three stereo RCA outputs to drive front, rear, and subwoofer audio ampliers
• An auxiliary stereo RCA input for use with portable devices, such as an MP3
player or DVD player
• Separate controls for master volume, subwoofer volume (sub level), front/rear
fader, and selection of main or auxiliary inputs
• Extended frequency response from 20Hz to 30kHz with exceptional 100dB
signal-to-noise performance
• Gold-plated RCA connectors to ensure the best audio signal output
• ISO mounting holes and removable trim ring for custom installation
• Bass Driver: The VIBE530P contains a Bass Driver circuit that accurately
recreates and injects Low fre quency information back into the signal path.
What that means in everyday terms is that the VIBE530P will give more bass
impact to your best compact discs or even your old tapes.
• Bass Equalization Circuit: The VIBE530P has a unique equalization circuit
that contours the restored base to your speaker systems.
• Bass Output Control: The VIBE530P has the ability to produce large amount
of deep, mind shattering bass without damaging your speakers. The Bass Output
Control circuit allows the VIBE530P to maximize the bass output of any auto
sound audio system while restraining destructive bursts.
www.Lanzar.com
4
PRECAUTIONS
• Do not operate this product in ways other than those described in this manual.
• Do not disassemble or modify this unit.
• Do not pour liquid or poke foreign objects into the unit.
Water and humidity may damage internal circuitry.
• If the unit becomes wet, turn o all power and ask your authorized LANZAR
dealer to clean or service the unit.
Failure to observe these precautions may damage your ear, the monitor, or the
video source, and may void the warranty.
Installation
Installation of mobile audio and video components requires experience with a
variety of mechanical and electrical procedures. Although this manual provides
general installation and operation instructions, it does not show the exact
installation methods for your particular vehicle. If you do not have the required
knowledge and experience to successfully complete the installation, consult an
authorized LANZAR dealer about professional installation options.
www.Lanzar.com
5
CONTROLS
AUX(auxiliary)switch: Press to
select auxiliary or main inputs
Equalizer gain controls
Subwoofer volume
Master volume
Voltage Level Indicator
Fader control: Use to balance sound
between front and rear speakers
Aux gain control: Gain adjustment for left and
right auxiliary input Para- Bass Controls: These 2 knobs control the
Para-Bass functions of the VIBE530P.
The SWEEP knob allows you to
pick the center frequency that you
want the VIBE530P bass restoration
ci
rcuit to maximize. The WIDE knob
abjusts how wide of a frequency range
the VIBE530P will effect.
Main gain control: Gain adjustment for left
and right auxiliary input
Low-pass frequency switch
(60 / 90Hz)
- Front panel controls -
- Rear panel connections -
- Top panel -
www.Lanzar.com
6
OPERATIONS
Setting system volume
1. Turn the master volume and subwoofer level controls to their minimum settings.
2. Turn the source unit on and increase the volume until you hear distortion.
3. Reduce the volume to just below the distortion point (approximately 80% of
full volume). This is the maximum usable musical signal for the source unit.
Turning the volume beyond this point increases noise and distortion without
increasing the musical signal.
Note:
Once you set the source unit volume, do not change it. Always use the volume
control on the VIBE530P as the master (main) volume control. The VIBE530P has
better electronics, a higher sound to noise ratio, and is more linear than the
volume settings on any source unit available.
Adjusting the Controls
The VIBE530P provides a graphic adjustment band for each of four frequency
ranges: sub,low, mid, mid-high and high frequency. You can adjust the center
of each frequency band to ne tune the acoustical response to your vehicle's
interior.
1. Set all frequencies to the center position.
The small dot on the control knob should be set at 12 o'clock.
2. Play your favorite music track and adjust the individual controls to suit your
taste. Avoid extreme settings, which can distort musical peaks.
3. Increase or decrease the equalizer gain controls to suit your taste.
4. If your system includes a subwoofer, slowly increase the subwoofer level until
you hear a solid bass.
5. If your system includes rear speakers, adjust the fader control to add rear sound.
Set it so most of the music comes from the front and only lls the rear.
Setting the low-pass frequency
Set the low pass frequency switch on the top of the VIBE530P to either 60Hz or
90Hz depending on the subwoofer and subwoofer amplier requirements.
www.Lanzar.com
7
Connecting an MP3 player or video unit
1. Plug the MP3 player or video unit into the auxiliary RCA input on the back of
the VIBE530P unit.
2. Make sure the auxiliary button on the front of the unit is out, ready to receive
input from the main RCA input (not the auxiliary RCA input).
3. Turn the VIBE530P master volume to a normal listening level.
4. Press the play button on the auxiliary source.
5. Push in the AUX button to change to the auxiliary source.
6. Using a small athead screwdriver, adjust the AUX gain controls located on the
top of the unit so that the volume of the auxiliary source matches the volume
of the main source.
Care and Maintenance
Cleaning the cabinet
Use a soft, dry cloth to gently wipe dust and dirt from the unit.
Do not use benzene, thinner, car cleaner, or other cleaners. These substances may
damage the unit or cause the paint to peel.
Servicing the equalizer/crossover unit
In the event that trouble arises, never open the case or disassemble the unit.
The internal parts are not serviceable by the user. Opening any components will
void the warranty.
CAUTION!
Changes or modications to this product that are not approved by the
manufacturer will void the warranty and will violate FCC approval.
INSTALL ATION AND WIRING
Read these instructions and the following precautions carefully.
What's in the Box:
• 5-Band Parametric Equalizer
• 2 Mounting brackets
• 8 Phillips-head Screws
• Power Red Wire with 1A Fuse
www.Lanzar.com
8
Before Starting
Mounting Precautions
The VIBE530P can be mounted next to the source unit or under the dash using
the mounting brackets. The front panel controls should be easily accessible from
the driver's seat.
In addition:
• This unit requires additional mobile audio components for proper operation.
• Always use great care when attaching anything to a vehicle! Check clearances in
front of, behind, and on both sides of the planned installation before drilling
any holes or installing any screws.
Wiring Precautions
Disconnect the ground (-) terminal on the vehicle's battery.
WARNING!
To Prevent short circuits during installation, always disconnect the vehicle's
negative (-) battery lead before making any connections.
• This unit is exclusively for vehicles with a negative ground, 12V battery system.
• A good chassis ground connection is critical to minimize resistance and avoid
noise problems. Use the shortest wire possible and securely connect it to the
car chassis and the source unit ground.
• When routing RCA cables, keep the cables away from the power cables and
output speaker wires.
• If you are using a source unit without a remote turn-on lead, the VIBE530P can
be turned on with a switched accessory lead. This accessory power source is
located in the factory harness at the back of the radio. This lead turns on and o
with the ignition key.
• Do not open the case. There are no user-serviceable parts inside. If you require
assistance, consult your LANZAR dealer or an authorized LANZAR service center.
www.Lanzar.com
9
Tools and additional components
You will need:
• A Philips-head screwdriver when mounting the unit in the vehicle.
• A small at-head screwdriver to adjust the AUX gain controls if you connect an
MP3 player or video source.
• High-quality RCA input and output cables.
Extra cable can cause signal loss and act as an antenna for noise.
Use only high-quality RCA cables that are no longer than necessary to make a
direct connection with the source unit and ampliers.
Mounting Diagram
www.Lanzar.com
10
Wiring Diagram
Tabla de contenidos
Otros manuales de Ecualizador estéreo de Lanzar
Lanzar
Lanzar VIBE XE3 Manual de usuario
Lanzar
Lanzar VIBE E740V Manual de usuario
Lanzar
Lanzar HTGEPBT9H Manual de usuario
Lanzar
Lanzar VBXEQ4P Manual de usuario
Lanzar
Lanzar VBE420P Manual de usuario
Lanzar
Lanzar HTGEPBT9 Manual de usuario
Lanzar
Lanzar Vibe 440PSU Manual de programación
Lanzar
Lanzar HTG50EBT Manual de usuario
Lanzar
Lanzar HTG50EBTH Manual de usuario
Lanzar
Lanzar VIBE E540P Manual de usuario
