L3 Aviation Products GH-3100 Manual de usuario

5353 52nd Street, S.E.

TP-559 (Revision K)

Grand Rapids, MI 49512-9704, USA

March 30, 2017

L3aviationproducts.com

Electronic Standby Instrument System

Model: GH-3100

Part Number: 501-1860-(xxx1)

Part Number: 501-1860-(xxx3)

Installation and Operation Manual

This manual contains installation and operating

information for the GH Electronic Standby Instrument

System. Information in this manual includes the following

products: GH-3100 Electronic Standby Indicator (with 1.3,

1.4 or 3.0 software), DCM-3100 Detachable Configuration

Module, and MAG-3000 / MAG-3100 Magnetometer. This

information is supplemented and kept current by

revisions, service letters and service bulletins.

Page A Front Section TP-559

March 30, 2017 Revision K

Foreword

This manual provides information intended for use by persons who, in accordance with current regulatory

requirements, are qualified to install this equipment. Installation requirements may vary, depending on the

particularities of each aircraft, and this manual is intended as a guideline for that purpose. This manual

assumes familiarity with the setup and operation of the aircraft systems that interface with the GH-3100.

Standard installation practices prescribed in FAA Advisory Circular No. 43.13-2B must be followed.

If further information is required, please contact:

L3 Aviation Products

Attn: Field Service Engineering

5353 52PP

PP Street, S.E.

Grand Rapids, MI USA 49512-9704

Telephone: (800) 453-0288 or (616) 949-6600

Fax: (616) 977-6898

Email: fieldservice.avionics@L3T.com

Web: www.L3aviationproducts.com

This manual is distributed with permission by:

L3 Aviation Products

5353 52PP

PP Street, S.E.

Grand Rapids, MI USA 49512-9704

Telephone: (800) 453-0288 or (616) 949-6600

Fax: (616) 977-6898

Email: avionics.techpubs@L3T.com

We welcome your comments concerning this manual. Although every effort has been made to keep it free

of errors, some may occur. When reporting a specific problem, please describe it briefly and include the

manual part number, the paragraph/figure/table number, and the page number. Send your comments to the

address or email above:

Disclaimer

This manual contains information that is considered relevant only at the time of distribution with the L3

Aviation Products product for which it is shipped. Information in this manual is subject to change without

notice.

1T21T

WARNING

INFORMATION SUBJECT TO EXPORT CONTROL LAWS

This technology is controlled under the Export Administration Regulations

(EAR) and may not be exported to a Foreign Person, either in the U.S. or

abroad, without proper authorization by the U.S. Department of

Commerce.

L3 Aviation Products

GH-3100

Installation & Operation Manual

TP-559 Front Section Page i

Revision K March 30, 2017

About This Manual

SECTION 1 – GENERAL INFORMATION

This section provides the following information: unit configurations, unit functionality, items

required but not supplied with the unit, equipment specifications, installation approval/limitations

and TSO approvals.

SECTION 2 - INSTALLATION

This section contains instructions to locate, assemble and install the GH-3100 Electronic Standby

System as well as information for unpacking equipment, and inspection procedure for in-shipment

damage.

SECTION 3 – INSTALLATION CHECKOUT

This section contains instructions for post installation setup and post installation checkout

procedures.

SECTION 4 – MAINTENANCE

This section contains general flightline maintenance procedures. It includes periodic maintenance,

troubleshooting, return to service procedures and instructions for the return of defective components.

APPENDIX A – SIGNAL AND CABLE CHARACTERISTICS

This appendix defines the electrical characteristics and wiring and label configuration options of all

input and output signals.

APPENDIX B – ENVIRONMENTAL QUALIFICATION FORM

This appendix provides the environmental qualification test data for the GH-3100 Indicator and

DCM-3100 Configuration Module.

Descriptions for Warnings, Cautions, and Notes are used throughout the manual to highlight important

information.

A WARNING is used to give notice to or call one's attention to beforehand especially of danger (such as

a warning to a Flight Crew person or a warning to a mechanic before performing a dangerous task).

A CAUTION is a statement that expresses the need for heightened awareness to conditions that can cause

damage to equipment.

A NOTE is used to point out a procedure, event, or practice that it is desirable to highlight.

GH-3100

Installation & Operation Manual

Page ii Front Section TP-559

March 30, 2017 Revision K

References

To get an up-to-date listing of all L3 Aviation Products technical publications and service literature go to

21T21Twww.L3aviationproducts.com21T21T, click on the Customer Support tab, select Technical Publications, and

select Current Publications on the left side of the screen.

Contact L3 Aviation Products Customer Service [1-800-453-0288] to determine availability of technical

publications and directives.

Service literature and publications can be obtained by either downloading from the L3 Technical

Publications website (may require secure site access) or by receiving a copy via email. Send an email

request to 21T21Tavionics.techpub[email protected]21T21T. Note – Additional request for software and databases may be

required.

PUBLICATION DESCRIPTION

TP-560 Pilot’s Guide, GH-3100

TP-603 Troubleshooting Guide, GH-3100

Letter of Equivalency Letter of equivalency for the GH-3100 software released 3.0.

TP-633 Installation Manual, MAG-3000 Magnetometer.

0040-21200-01 Installation Manual, MAG-3100 Magnetometer.

TP-623 Instruction Manual, JT-147A Calibration Test Set

SL-179 Service Letter - Fan Failures During Power ON Self Test Mode

SL-186 Service Letter - Provide factory generated tolerance settings of altitude

accuracy for certified repair stations.

SL-189 Service Letter –

1. Import / Export control issues.

2. Modification status of models GH-3000, GH-3004, and GH-3100.

SL-244 Service Letter - To inform customers about the replacement of the GH-3100

with software version 1.3 with the new GH-3100 with software version 3.0.

SL-245 Service Letter - During initial or user initiated alignment, attitude error may

be introduced during transition to the external heading source.

SB501-1860-1 Service Bulletin - To ease manufacturing and repair of the keyboard

assembly.

SB501-1860-2 Service Bulletin - To correct startup errors for Level Sensor Self Test.

SB501-1860-3 Service Bulletin - Provide replacement display due to diminishing source.

SB501-1860-4 Service Bulletin - Correct insufficient timing margin for 16-BIT A/D High

Byte-Low Byte Select Line.

SB501-1860-5 Service Bulletin - Provide additional screw depth engagement in sensor

mounting bracket.

SB501-1860-6 Service Bulletin - Manufacturing Change. Produce a universal Lighting

Controller.

SB501-1860-7 Service Bulletin - Manufacturing Change. Provide replacement for Pitch

Rate Sensor Flex.

SB501-1860-8 Service Bulletin - Manufacturing Change. Provide replacement for Roll Rate

Sensor Flex.

SB501-1860-9 Service Bulletin - Manufacturing Change. Provide replacement for Yaw

Sensor Flex.

GH-3100

Installation & Operation Manual

TP-559 Front Section Page iii

Revision K March 30, 2017

PUBLICATION DESCRIPTION

SB501-1860-10 Service Bulletin - Release of 2.1 software in support of Gulfstream G450

program.

SB501-1860-11 Service Bulletin - Release Software 1.1. New features include the capability

to compensate IAS with DCM-3100 loaded constants K1 and K2.

SB501-1860-12 Service Bulletin - To reduce the possibility of the display blanking or failing at

start up.

SB501-1860-13 Service Bulletin - To reduce the possibility of the display blanking or

disruption.

SB501-1860-14 Service Bulletin - To prevent unrecoverable loss of alignment during dynamic

motion with units configured without heading sources.

SB501-1860-15 Service Bulletin - Provide replacement display due to diminishing source.

SB501-1860-16 Service Bulletin - Add SSEC disable to GH SSEC selection and removal of

fan failure warning. (Software load 2.2)

SB501-1860-17 Service Bulletin - Add SSEC disable to GH SSEC selection and removal of

fan failure warning. (Software load 2.2)

SB501-1860-18 Service Bulletin - To improve attitude performance when configured without

heading. Maintenance release to address open action items.

SB501-1860-19 Service Bulletin - Provide replacement display due to diminishing source.

SB501-1860-20 Service Bulletin - Software update to correct alignment error at startup as a

result of power sequencing. This condition only affects units configured for

ARINC 429 heading input source using the following DCM-3100 part

numbers:

SB501-1860-20AWG Service Bulletin – (Agusta Westland only) Software update to correct

alignment error at startup as a result of power sequencing. T

his condition only

affects units configured for ARINC 429 heading input source using the

following DCM-3100 part numbers:

SB501-1860-21 Service Bulletin - This product may have a suspected unapproved part (SUP)

installed. This service bulletin creates an inspection MOD, effective at next

service, which identifies units that have had this condition corrected.

SB501-1860-22 Service Bulletin – (501-1860-2103 only) To incorporate quick disconnect

fittings to Static Pressure Port (MS33649-05) and Total Pressure Port

(MS33649-04).

SB501-1860-23 Service Bulletin - Inspect for suspect unapproved part (SUP).

GH-3100

Installation & Operation Manual

Page iv Front Section TP-559

March 30, 2017 Revision K

List of Effective Pages

Dates of original and changed pages are:

Revision A ................................May 24, 2002

Change 1.......................October 10, 2002

Change 2..........................March 21, 2003

Revision B ............................August 02, 2004

Revision C..................................April 4, 2005

Revision D................................May 22, 2006

Revision E ..........................October 31, 2006

Revision F ..........................January 26, 2009

Revision G................................May 20, 2009

Revision H.........................February 23, 2010

Revision J........................ September 4, 2012

Revision K .............................March 30, 2017

Total number of pages in this publication consists of the following:

Title page

A Page

i thru x

1-1 thru 1-12

2-1 thru 2-12

3-1 thru 3-12

4-1 thru 4-6

5-1 thru 5-34

A-1 thru A-10

B-1 thru B-4

REVISION HIGHLIGHTS

Revision K is a republication. This republication completely replaces the existing manual. New and

revised material for the GH-3100 Installation Manual has been added. These changes include:

•Update company name and email/web site.

•Update frontmatter to current format.

•Pg. 2-1: Change 4 gauss to 5 gausses in caution.

•Pg. 2-3: Insert new step 8 for clamp torque settings.

•Pg. 1-10: Update information concerning the calibration test set and the MAT-3100.

Discard all previous revisions of this manual.

GH-3100

Installation & Operation Manual

TP-559 Front Section Page v

Revision K March 30, 2017

Table of Contents

Paragraph Page

Foreword.......................................................................................................................................................A

About This Manual......................................................................................................................................... i

References..................................................................................................................................................... i

List of Effective Pages...................................................................................................................................iv

Revision Highlights........................................................................................................................................iv

Table of Contents.......................................................................................................................................... v

List of Illustrations .......................................................................................................................................viii

List of Tables.................................................................................................................................................ix

List of Abbreviations...................................................................................................................................... x

SECTION 1

GENERAL INFORMATION

1.1 Introduction ...................................................................................................................................1-1

1.2 Functional description...................................................................................................................1-3

1.2.1 Electronic Standby Indicator (GH-3100).......................................................................................1-4

1.2.2 Detachable Configuration Module (DCM-3100)............................................................................1-5

1.2.3 Magnetometer (MAG-3000)..........................................................................................................1-5

1.2.4 Magnetometer (MAG-3100)..........................................................................................................1-5

1.3 Specifications................................................................................................................................1-6

1.3.1 GH-3100........................................................................................................................................1-6

1.3.2 DCM-3100.....................................................................................................................................1-8

1.4 Modifications and Software Revisions ..........................................................................................1-8

1.4.1 Software Release Summery .........................................................................................................1-8

1.5 Interfaces ......................................................................................................................................1-8

1.6 Equipment Required Not Supplied................................................................................................1-9

1.7 installation approval and Limitations...........................................................................................1-11

GH-3100

Installation & Operation Manual

Page vi Front Section TP-559

March 30, 2017 Revision K

Table of Contents (continued)

Paragraph Page

SECTION 2

INSTALLATION

2.1 Introduction ...................................................................................................................................2-1

2.2 Unpacking and inspecting.............................................................................................................2-1

2.2.1 Transport and Storage Considerations.........................................................................................2-1

2.3 Installation Procedures..................................................................................................................2-2

2.3.1 GH-3100 Electronic Standby Indicator..........................................................................................2-2

2.3.2 DCM-3100 Detachable Configuration Module..............................................................................2-3

2.3.3 Electrical Connections...................................................................................................................2-6

2.3.4 Installation Guidelines for MAG-3000 Magnetometer...................................................................2-7

2.3.5 Installation Guidelines for MAG-3100 Magnetometer...................................................................2-8

SECTION 3

INSTALLATION CHECKOUT

3.1 Introduction ...................................................................................................................................3-1

3.2 Post Installation Checks (Initial System Installation) ....................................................................3-1

3.2.1 Electronic Standby Indicator Check..............................................................................................3-1

3.2.2 Magnetometer Check....................................................................................................................3-2

3.2.3 Post Installation Checks (Remove and Replace Checkout).......................................................3-11

SECTION 4

MAINTENANCE

4.1 Introduction ...................................................................................................................................4-1

4.2 Continued Airworthiness...............................................................................................................4-1

4.2.1 Periodic Maintenance....................................................................................................................4-1

4.2.2 Pneumatic Pressure Checks.........................................................................................................4-1

4.3 Fault Isolation................................................................................................................................4-3

4.4 Return to Service ..........................................................................................................................4-5

4.5 Disposition of Failed Items............................................................................................................4-5

4.5.1 GH-3100 Electronic Standby Indicator..........................................................................................4-5

4.5.2 DCM-3100 Data Configuration Module.........................................................................................4-6

4.5.3 Magnetometer (MAG-3100 and MAG-3000).................................................................................4-6

GH-3100

Installation & Operation Manual

TP-559 Front Section Page vii

Revision K March 30, 2017

Table of Contents (continued)

Paragraph Page

SECTION 5

OPERATION

5.1 Introduction ...................................................................................................................................5-1

5.2 Functional Description...................................................................................................................5-1

5.2.1 Front Panel Controls.....................................................................................................................5-1

5.2.2 Menu Interface ..............................................................................................................................5-2

5.2.3 Operational Formats .....................................................................................................................5-7

5.2.4 Air Data Presentation..................................................................................................................5-12

5.2.5 Navigation Data...........................................................................................................................5-19

5.2.6 Heading Data..............................................................................................................................5-23

5.3 Operational Functions.................................................................................................................5-25

5.3.1 Power ON Sequence ..................................................................................................................5-25

5.3.2 Pitch and Roll Attitude Display....................................................................................................5-26

5.3.3 Slip / Skid Indicator .....................................................................................................................5-27

5.3.4 Air Data Display ..........................................................................................................................5-27

5.3.5 NAV Displays ..............................................................................................................................5-28

5.3.6 Magnetic Heading Display Data..................................................................................................5-34

APPENDIX A

GH-3100 INTERFACE SIGNAL NAME & CABLE CHARACTERISTICS

A.1 Introduction ...................................................................................................................................A-1

A.2 Digital Interface .............................................................................................................................A-1

A.2.1 ARINC 429 Input BUS...................................................................................................................A-1

A.2.2 CSDB Input BUS...........................................................................................................................A-2

A.2.3 RS-422 Input BUS.........................................................................................................................A-3

A.2.4 BUS Configuration Options...........................................................................................................A-3

A.3 Electronic Standby Indicator, [J1 connector] ................................................................................A-4

APPENDIX B

ENVIRONMENTAL QUALIFICATION FORM

B.1 GH-3100 & DCM-3100 Environmental Qualification Form...........................................................B-1

GH-3100

Installation & Operation Manual

Page viii Front Section TP-559

March 30, 2017 Revision K

List of Illustrations

Figure Page

1-1: GH-3100 Electronic Standby Instrument System...........................................................................1-2

1-2: JT-147A Calibration Test Set........................................................................................................1-11

2-1: DCM-3100 Outline Dimensions......................................................................................................2-3

2-2: GH-3100 Outline Dimensions and J1 Pin Assignments.................................................................2-4

2-3: GH-3100 Cable Assembly (J1).......................................................................................................2-6

2-4: System Electrical Interface Diagram with MAG-3000.....................................................................2-9

2-5: System Electrical Interface Diagram with MAG-3100...................................................................2-10

3-1: Example of Plane on Compass Rose.............................................................................................3-4

3-2: ILS Display......................................................................................................................................3-5

3-3: VOR Display ...................................................................................................................................3-6

3-4: DME Display ...................................................................................................................................3-6

3-5: FMS Display....................................................................................................................................3-7

3-6: TACAN Display...............................................................................................................................3-8

5-1: Indicator Front Panel.......................................................................................................................5-1

5-2: Attitude Display with Callouts .........................................................................................................5-7

5-3: Chevrons in Excessive Pitch Attitude Display ................................................................................5-8

5-4: Full Screen Attitude Failure Display..............................................................................................5-10

5-5: Processor Error Screens ..............................................................................................................5-11

5-6: Attitude Display with Airspeed and Altitude..................................................................................5-12

5-7: Altitude Displays ...........................................................................................................................5-13

5-8: Invalid Air Data Displays...............................................................................................................5-15

5-9: IAS Tape Displays ........................................................................................................................5-16

5-10: IAS Invalidity Displays ................................................................................................................5-18

5-11: VOR Mode with DME..................................................................................................................5-19

5-12: ILS Mode with DME....................................................................................................................5-20

5-13: FMS Mode ..................................................................................................................................5-20

5-14: TACAN Mode..............................................................................................................................5-21

5-15: Heading Tape, VOR Mode .........................................................................................................5-23

5-16: Heading Tape, FMS Mode..........................................................................................................5-23

5-17: Heading Invalidity with X.............................................................................................................5-24

5-18: Heading Invalidity with Box.........................................................................................................5-24

5-19: Example of ARINC 429 NAV & CSDB NAV Interconnect ..........................................................5-29

Tabla de contenidos

Otros manuales de GPS de L3 Aviation Products

L3 Aviation Products

L3 Aviation Products Lynx NGT-9000+ Manual

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario