Kusam-meco KM 887 Manual de instalación

—

— LCD

—

VFD V & Hz readings.

Record MAX/MIN regular readings.

Display Hold Function.

Backlight Display

GENERAL SPECIFICATIONS :

Sensing : AC, True RMS

Display : 3-5/6 digits 6000 Counts Backlight LCD Display.

61 Segments Bar Graph : 40 per second max.

Auto Power Off.

Polarity : Automatic

Update Rate : 5 per second nominal

Operating Temperature : -10ºC ~ 50ºC

Relative Humidity : Maximum relative humidity 90% for temperature

up to 28ºC decreasing linearly to 50% relative humidity at 50ºC.

Pollution degree : 2

P Rating : IP40

Storage Temperature : -20ºC ~ 60ºC, < 80% R.H. (with battery removed)

Altitude : Operating below 2000m

Temperature Coefficient : Nominal 0.1 x (specified accuracy)/ °C @(-10ºC~18ºC or 28ºC~50ºC),

or otherwise specified.

Low Battery: approx. 4.6V

APO Timing: Idle for 20 minutes

APO Consumption: 20mA typical

Power Supply: Four Alkaline AA batteries

+Hz

Power Consumption: 6.5mA typical except the followings : VFD ACV : 8mA

Insulation Resistance @ 1mA Test Current :

50V output Voltage : 25mA, 100V output Voltage : 45mA

250V output Voltage : 85mA, 500V output Voltage : 170mA

1000V output Voltage : 440mA

Tester can perform at least 950 Insulation Tests with new alkaline batteries at room temperature.

These are standard tests of 1000V into 1MW with a duty cycle of 5 seconds on and 25 seconds off.

Dimension: 208(L) X 103(W) X 64.5(H) mm with holster

Weight: 635 gm with holster.

TRUE RMS DIGITAL INSULATION MULTIMETER

MODEL KM 887

Preliminary Data

D:/Chhaya/My Documents/Chhaya/backup/catlogs/NEW CAT/2015 new arrival catalogs/KM887.cdr

An ISO 9001:2008 Company

®®

SPECIAL FEATURES :

All Specifications are subject to change without prior notice

NEW

— Dual

—

Display +Hz readings.

Relative zero mode.

LOCK-Test mode for Insulation Resistance

BeepJack audible & visible input warning.

High resolution 60.00mV & 60.00W ranges.

SAFETY :

Safety : Double insulation per IEC / UL / EN61010-1 Ed. 3.0, IEC / UL / EN61010-2-030 Ed. 1.0, IEC / UL / EN61010-2-033 Ed. 1.0,

IEC / UL / EN61010-031 Ed. 1.1 & the corresponding CAN / CSA-C22.2 regulations to Measurement CAT III 1000V AC & DC & CAT IV 600V AC & DC.

Compliance to IEC / EN61557:2007 : (per CE requirements, not certified by UL or ETL) : IEC / EN61557-1 & IEC / EN61557-2 .

Overload Protections :

Insulation Resistance, mA & mA : 0.4A/1KV, IR 30kA, F Fuse, or better

A : 11A/1KV, IR 20kA, F Fuse or better

V : 1100Vrms

mV, W & Others : 1000 Vrms

E.M.C. : Meets EN61326-1:2013

In an RF field of 3V/m:

Total Accuracy = Specified Accuracy + 25 digits.

Performance above 3V/m is not specified.

Transient Protection : 8KV(1.2/50mS Surge)

ACCESSORIES :

ACCESSORIES : BKB32 banana plug to type-K socket plug adaptor,

Test probe pair, BRP21S2-C Remote probe, Alligator clip pair, Holster, Bkp60 banana plug type-K thermocouple & User manual.

OPTIONAL Magnetic hanger, & BMP-86x Carrying Case.

D:/Chhaya/My Documents/Chhaya/backup/catlogs/NEW CAT/2015 new arrival catalogs/KM 887.cdr

ELECTRICAL SPECIFICATIONS : KM 887

o o

Accuracy is ± (% of reading digits + number of digits) or otherwise specified, at 23 C ± 5 C & less than 80%relative humidity.

True RMS voltage & current accuracies are specified from 1 % to 100 % of range or otherwise specified.

Maximum Crest Factor < 1.8:1 at full scale & < 3.6:1 at half scale, and with frequency components fall within the specified frequency bandwidth

for non-sinusoidal waveforms.

Range

VFD AC VOLTAGE

Accuracy

Resolution

10Hz ~ 45Hz

±(4%rdg + 5dgts)

100 mV

600.0 V

45Hz ~ 200Hz

±(2.5%rdg + 5dgts)

100 mV

600.0 V

Input impedance : 10M , 110pF nominal.

1) Unspecified for fundamental frequency > 440Hz

2) Accuracy linearly decreases from 2.5% + 5d @ 200Hz to 9.0% + 5d @ 440Hz

200Hz ~ 440Hz

±(9.0%rdg + 5dgts)2)

100 mV

600.0 V

All Specifications are subject to change without prior notice

RESISTANCE

60.00W2)

Accuracy

Resolution

Range1)

0.01 mW±(0.5%rdg + 5dgts)

6.000kW

±(0.2%rdg + 2dgts)

1 W

60.00kW10 W

Open Circuit Voltage : 1.7VDC typical

Specified assumes input lead resistance been offset by RELD or Shrt (short)

feature.

Constant Test Current : 0.2mA typical

Add 1% @ >20MW

Add 2% @ operation temperature >35°C

600.0kW100 W

6.000M 3)

W1 kW±(1%rdg + 3dgts)

60.00M 4)

W10 kW

±(1.5%rdg + 6dgts)5) 6)

600.0W100 mW±(0.2rdg + 3dgts)

±(0.3%rdg + 2dgts)

AUDIBLE CONTINUITY TESTER

Audible Threshold Between 20 and 350W W

Response Time < 30ms approx.

Input Impedance : 10MW, 110pF nominal

1) Add 20d @ >80% of range

2) Unspecified @ <5% of range

Range

AC VOLTAGE

Accuracy

Resolution

50Hz ~ 60Hz

±(0.7%rdg + 4dgts)

1 mV

6.000 V

10 mV

60.00 V

100 mV

600.0 V

1 V

1000 V

0.01 mV

60.00 mV

0.1 mV

600.0 mV

40Hz ~ 1kHz

±(1.3%rdg + 4dgts)

1 mV

6.000 V

10 mV

60.00 V

100 mV

600.0 V

1 V

1000 V

0.01 mV

60.00 mV

0.1 mV

600.0 mV

±(2%rdg + 4dgts)

1kHz ~ 5kHz

±(2%rdg + 4dgts)

1 mV

6.000 V

10 mV

60.00 V

100 mV

600.0 V

1 V

1000 V

0.01 mV

60.00 mV

0.1 mV

600.0 mV

Unspecified

5kHz ~ 20kHz

±(2%rdg + 20dgts)

1 mV

6.000 V

10 mV

60.00 V

100 mV

600.0 V

1 V

1000 V

0.01 mV

60.00 mV

0.1 mV

600.0 mV

Unspecified

60.00 mV

600.0 mV

±(0.1%rdg + 2dgts)

DC VOLTAGE

Accuracy

Resolution

Range

0.01 mV

0.1 mV

Input Impedance : 10MW, 110pF nominal

6.000 V

60.00 V

1 mV

10 mV

600.0 V 100 mV

1000 V

±(0.2%rdg + 3dgts)

1 V

±(0.2%rdg + 3dgts)

RECORD MODE

This mode records standard measurement Max & Min

readings on most functions, Manual or Auto-ranging

where available.

Nominal response & accuracy : Same as standard

measurement.

2.700 V ±(1.5%rdg + 4dgts)

DIODE TESTER

Accuracy

Resolution

Range

1 mV

Test Current : 0.4mA typically

Open Circuit Voltage : < 2.8VDC typically

G-17, Bharat Industrial Estate, T. J. Road, Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct.: 022-24156638, Tel. : 022-24124540, 24181649, Fax : 022-24149659

Email : [email protected], Website : www.kusamelectrical.com

An ISO 9001:2008 Company

®®

D:/Chhaya/My Documents/Chhaya/backup/catlogs/NEW CAT/2015 new arrival catalogs/KM 887.cdr

ELECTRICAL SPECIFICATIONS : KM 887

All Specifications are subject to change without prior notice

1) mA / mA DC accuracies will be affected by extreme interior temperatures of the meter.

for rated accuracies, allow 6 to 20 minutes cool down interval after measuring A-currents of

3 to 10A continuously.

2) £ 400mA continuous : >400mA for < 1.1 hours on per > 20 minutes off

3) 10A continuous upto ambient 35°C; < 15 mins on per >5 mins off @ 35°C~50°C.

>10A to 20A for < 30 second on per >5 mins off.

DC CURRENT

Range Resolution Accuracy Burden Voltage

600.0 mA

60.00 mA1)

600.0 mA1) 2)

±(0.7%rdg + 2dgts)

0.2mV / mA

3mV / mA

30mV / A

6000 mA1)

6.000 A

10.00 A3)

0.1 mA

0.01 mA

0.1 mA

1 mA

0.001 A

0.01 A

±(0.2%rdg + 4dgts)

±(0.2%rdg + 2dgts)

±(0.3%rdg + 3dgts)

±(0.5%rdg + 4dgts)

INSULATION RESISTANCE

3.000M , 30.00M , 55.0MW W W

3.000M , 30.00M , 110.0MW W W

3.000M , 30.00M , 275.0MWWW

1) Actual output voltage : 100% ~ 120% of Test Voltage

Live Circuit Detector : Inhibit test and display voltage reading instead if terminal voltage > 30V

prior to initialization of test.

Display Voltage Accuracy : DCV : 1.5% + 5d , ACV : 3.0% + 5d @50Hz ~ 60Hz

Specified measuring range is 0.020MW....25.0GW for percentage operating uncertainly B(%)

£ ± 30% per IEC/EN61557-2 requirements.

3.000M , 30.00M , 300.0MWWW,

50 V

100 V

Test Voltage

250 V

500 V

Range Test Current

1mA @50kW

1mA @100kW

1mA @250kW

1mA @500kW

Accuracy

±(1.5%rdg + 5dgts)

3.000M , 30.00M , 300.0MWWW

1000 V 3000MW

25.0GW

1mA @1MW

±(10%rdg + 5dgts)

±(1.5%rdg + 5dgts)

±(2.0%rdg + 5dgts)

550.0MW

AC CURRENT

Range Resolution Accuracy Burden Voltage

2) 10A continuous upto ambient 35°C; < 15 mins on per >5 mins off

@ 35°C~50°C. >10A to 20A for < 30 second on per >5 mins off.

£ 400mA continuous : >400mA for < 1.1 hours on per > 20 minutes off

600.0 mA

60.00 mA

600.0 mA1)

0.2mV / mA

3mV / mA

30mV / A

6000 mA

6.000 A

10.00 A2)

0.1 mA

0.01 mA

0.1 mA

1 mA

0.001 A

0.01 A

±(1%rdg + 3dgts)

50Hz ~ 60Hz

600.0 mA

60.00 mA

600.0 mA1)

0.2mV / mA

3mV / mA

30mV / A

6000 mA

6.000 A

10.00 A2)

0.1 mA

0.01 mA

0.1 mA

1 mA

0.001 A

0.01 A

±(2%rdg + 3dgts)

40Hz ~ 3kHz

600.0 mA

60.00 mA

600.0 mA1)

0.2mV / mA

3mV / mA

30mV / A

6000 mA

6.000 A

10.00 A2)

0.1 mA

0.01 mA

0.1 mA

1 mA

0.001 A

0.01 A

3kHz ~ 5kHz

Unspecified

±(2%rdg + 5dgts)

~ Hz Line Level Frequency

Accuracy : ±(0.02%rdg + 4dgts)

Sensitivity

(Sine RMS) Range

4 mV 6Hz ~ 50kHz

40 mV 10Hz ~ 100kHz

0.4 V 10Hz ~ 50kHz

4 V

40 V

10Hz ~ 5kHz

400 V

40 V 10Hz ~ 440Hz

40 mA

Function Range

60 mV

600 mV

6 V

60 V

600 V

1000 V

VFD 600 V

600 mA

6000 mA 400 mA10Hz ~ 5kHz

600 mA 40 mA

0.6 A 10Hz ~ 3kHz

6 A

10 A 6 A

60 mA 4 mA

10Hz ~ 30kHz

CAPACITANCE

Range Resolution Accuracy1)

2.000 mF 2) ±(1.5%rdg + 5dgts)

20.00 mF

200.0 mF

±(5%rdg + 5dgts)

2000 mF

20.00 mF

1) Accuracies with film capacitor or better

2) Specified from 0.200mF

0.001 mF

0.01 mF

0.1 mF

1 mF

0.01 mF

the ambient (isothermal stage) for a correct junction voltage

compensation. Allow enough time to reach the isothermal

stage for a significant change of ambient temperature.

It can take up to an hour for changes > 5°C.

2) Type-K thermocouple range & accuracy not included.

Accuracies assume meter interior has the same temperature of

o o

-40.0 C to 0.0 C 1% + 2 C

TEMPERATURE

Range Accuracy 1) 2)

o o

0.0 C to 50.0 C

o o

50.0 C to 537.0 C

o o

-40.0 F to 32.0 F

o o

32.0 F to 122.0 F

o o

122.0 F to 999.0 F

2.2 C

1% + 2 C

1% + 3.6 F

4 F

1% + 3.6 F

®®

AN ISO 9001:2008 COMPANY

MODEL - KM 887

TRMS DIGITAL

INSULATION MULTIMETER

OPERATION MANUAL

G 17, Bharat Industrial Estate, T. J. Road,

Sewree (W), Mumbai - 400 015. INDIA.

Sales Direct : (022) 24156638

Tel. : (022) 24124540, 24181649. Fax : (022) 24149659

Email : [email protected]

Website : www.kusamelectrical.com

www.kusam-meco.co.in

LIST OF PRODUCTS

¬ Digital Multimeter ¬ Digital AC & AC/DC Clampmeter

¬ AC Clamp Adaptor ¬ AC/DC Current Adaptor

¬ Thermo Anemometer ¬ Thermo Hygrometer

¬ Distance Meter ¬ Digital Lux Meter

¬ Network Cable Tester ¬ Power Factor Regulator

¬ Earth Resistance Tester ¬ Digital Panel Meters

¬ DC Power Supplies ¬ High Voltage Detector

¬ Calibrators ¬ Gas Analysers

¬ Frequency Counter ¬ Function Generator

¬ Phasing Sticks ¬ Battery Tester

¬ Waterproof Pen Testers ¬ Solar Power Meter

¬ EMF Detector

¬ Wood, Paper & Grain Moisture Meter

¬ Transistorised Electronic Analog & Digital Insulation

Resistance Testers(upto 10 KV)

¬ Digital Sound Level Meter & Sound Level Calibrator

¬ Digital contact & Non-contact Type Tachometer

¬ Digital Non-contact (infrared) Thermometer

¬ Maximum Demand Controller/Digital Power Meter

¬ Digital Hand Held Temperature Indicators

TRMS DIGITAL

INSULATION MULTIMETER

MODEL - KM 887

TABLE OF CONTENTS

TITLE PAGE NO.

I. .............................

II. Cenelec Directives......................................

Safety..............................

IV. General Specifications...............................

III. Special Features.........................................

V. Product Description

. Test Certificate...........................................

IX. Warranty......................................................

...................................

VI. Operation....................................................

VII. Maintenance................................................

VIII

I. SAFETY :

Terms in this manual :

WARNING : Identifies conditions and actions that could result in

serious injury or even death to the user.

This manual contains information and warnings that must be

followed for operating the instrument safely and maintaining the

instrument in a safe operating condition. If the instrument is used in

a manner not specified by the manufacturer, the protection

provided by the instrument may be impaired.

CAUTION : Identifies conditions and actions that could cause

damage or malfunction in the instrument.

WARNING :

To reduce the risk of fire or electric shock, do not expose this

product to rain or moisture. The Meter is intended only for indoor

use, Observe proper safety precautions when working with voltages

above 33 Vrms, 46.7 Vpeak or 70 VDC. These voltage levels pose

a potential shock hazard to the user. Before and after hazardous

voltage measurements, check the voltage function on a known

source such as line voltage to determine proper meter functioning.

The meter meets UL/IEC/EN61010-1 Ed. 3.0, CAN/CSA C22.2

No. 61010-1 Ed. 3.0, UL/IEC/EN61010-2-033 Ed. 1.0 to

Measurement CAT-III 1kV and CAT-IV 600V, AC & DC. The meter

also meets the relevant Parts of EN61557. In particular, Part 1

Ed. 2.0, Part 2 Ed. 2.0 and Part 10 Ed. 2.0. These relevant parts of

EN61557 are not covered by the ETL certification. The accompanied

test probe assembly meets UL/IEC/EN61010-031 Ed. 1.1 to the

same meter ratings or better. IEC 61010-031 requires exposed

conductive test probe tips to be ≤ 4mm for CAT III & CAT IV ratings.

Refer to the category markings on your probe assemblies as well as

on the add-on accessories (like detachable Caps or Alligator Clips),

if any, for applicable rating changes.

Keep your hands/fingers behind the hand/finger barriers (of the

meter and the test probe assembly, where applicable) that indicate

the limits of safe access of the hand-held parts during

measurements. Inspect lead wires, connectors, and probes for

damaged insulation or exposed metal before using the meter. If

any defects are found, replace them immediately. Only use the

probe assembly provided with the meter or a UL Listed Probe

Assembly to the same meter ratings or better.

CAUTION :

Disconnect the test leads from the test points before changing

functions.

INTERNATIONAL ELECTRICAL SYMBOLS :

Marking of Electrical and Electronic Equipment (EEE).

Do not dispose of this product as unsorted municipal

waste. Contact a qualified recycler

Caution ! Refer to the explanation in this Manual

Caution ! Risk of electric shock

Earth (Ground)

Double Insulation or Reinforced insulation

Fuse

AC--Alternating Current

DC--Direct Current

Three-phase Alternating Current

II. CENELEC DIRECTIVES :

The instruments conform to CENELEC Low-voltage directive

2014/35/EC, Electromagnetic compatibility directive 2014/30/EU &

RoHS directive 2011/65/EU.

Measurement Category

Measurement Category IV is applicable to test & measuring circuits

connected at the source of the building’s low-voltage MAINS

installation. Examples are measurements on devices installed before

the main fuse or circuit breaker in the building installation.

Measurement Category III is applicable to test & measuring circuits

connected to the distribution part of the building’s low-voltage MAINS

installation. Examples are measurements on distribution boards

(including secondary meters), circuit-breakers, wiring, including

cables, bus-bars, junction boxes, switches, socket-outlets in the fixed

installation, & equipment for industrial use & some other equipment

such as stationary motors with permanent connection to the

fixed installation

Measurement Category II is applicable to test & measuring circuits

connected directly to utilization points (socket outlets & similar points)

of the low-voltage MAINS installation. Examples are measurements

on MAINS CIRCUITS of household appliances, portable tools &

similar equipment.

IV. GENERAL SPECIFICATIONS :

Display : 3-5/6 digits 6,000 counts

Polarity : Automatic

Update Rate : 5 per second nominal

61 Segments Bar graph : 40 per second max

Operating Temperature : -10°C to 50°C

Relative Humidity : Maximum relative humidity 90% for temperat-

ure up to 28°C decreasing linearly to 50% relative humidity at 50°C

Pollution Degree : 2

IP Rating : IP40

Storage Temperature : -20°C to 60°C, < 80% R.H. (with battery

removed)

Altitude : Operating below 2000m

Temperature Coefficient : nominal 0.1 x (specified accuracy) /

°C @(-10°C ~ 18°C or 28°C ~ 50C), or otherwise specified

Sensing : AC, True RMS

Safety : ETL certified per IEC/UL/EN61010-1 Ed. 3.0,

IEC/UL/EN61010-2-030 Ed. 1.0, IEC/UL/EN61010-2-033 Ed. 1.0,

IEC/UL/EN61010-031 Ed. 1.1 and the corresponding CAN

/CSA-C22.2 regulations to Measurement Categories:

CAT III 1000 V AC & DC and Category IV 600V AC & DC

Compliance to IEC/EN61557:

IEC/EN61557-1 Ed. 2.0, IEC/EN61557-2 Ed. 2.0 &

IEC/EN61557-10 Ed. 2.0

(Tested per CE requirements, not covered by ETL certification)

Overload Protections :

Insulation Resistance, μA & mA: 0.4A/1KV, IR 30kA,

F Fuse; or better

A: 11A/1KV, IR 20kA, F Fuse; or better

V: 1100Vrms

mV, & Others: 1000 Vrms

Transient Protection : 8kV (1.2/50s surge)

E.M.C.: Meets EN61326-1:2013

In an RF field of 3V/m:

Total Accuracy = Specified Accuracy + 25 digits

Performance above 3V/m is not specified

Power Supply : Four Alkaline AA batteries (IEC Lr6)

Power Consumption : 6.5mA typical except the followings:

VFD ACV +Hz: 8mA

Insulation Resistance @1mA test current:

50V output voltage: 25mA

100V output voltage: 45mA

250V output voltage: 85mA

500V output voltage: 170mA

1000V output voltage: 440mA

Tester can perform at least 950 insulation tests with new alkaline

batteries at room temperature. These are standard tests of 1000 V

into 1 M with a duty cycle of 5 seconds on and 25 seconds off.

Low Battery : approx. 4.6V

APO Timing : Idle for 20 minutes

APO Consumption : 20A typical

Dimension : 208(L) X 103(W) X 64.5(H) mm with holster

Weight : 635 gm with holster

Accessories : Test probe pair, Alligator clip pair, BRP21S2-C

Remote probe, Holster, User's manual, Bkp60 banana plug type-K

thermocouple

Optional Accessories : BKB32 banana plug to type-K socket plug

adaptor, BMH-01 magnetic hanger; BMP-86x soft carrying pouch

Special Features :

• Record MAX/MIN regular readings

• Relative Zero

• Display Hold

• LCD Backlight

• VFD V & Hz readings

• Dual display +Hz Readings

• High resolution 60.00mV & 60.00 ranges

• Lock-Test mode for Insulation resistance

• BeepJack audible & visible input warning

ELECTRICAL SPECIFICATIONS :

Accuracy is ± (% reading digits + number of digits) or otherwise

specified, at 23°C ± 5°C & less than 80% relative humidity. True

RMS voltage & current accuracies are specified from 1 % to 100 %

of range or otherwise specified. Maximum Crest Factor < 1.8:1 at

full scale & < 3.6:1 at half scale, and with frequency components

within the specified frequency bandwidth for non-sinusoidal

waveforms.

AC Voltage :

Range Resolution Accuracy

50Hz ~ 60Hz

60.00mV

600.0mV

6.000V

60.00V

600.0V

1000V

0.01

0.1

0.001

0.01

0.1

±(0.7%rdg + 4dgts)

40Hz ~ 1kHz

±(2%rdg + 4dgts)

60.00mV

600.0mV

6.000V

60.00V

600.0V

1000V

0.01

0.1

0.001

0.01

0.1

±(1.3%rdg + 4dgts)

1kHz ~ 5kHz

Unspecified

60.00mV

600.0mV

6.000V

60.00V

600.0V

1000V

0.01

0.1

0.001

0.01

0.1

±(2%rdg + 4dgts)

5kHz ~ 20kHz

Unspecified

60.00mV

600.0mV

6.000V

60.00V

600.0V

1000V

0.01

0.1

0.001

0.01

0.1

±(2%rdg + 20dgts)

Unspecified

±(2.5%rdg + 20dgts)

Input impedance: 10MW, 110pF nominal

1) Add 20d @ >80% of range

2) Unspecified @ <5% of range

3) Signal peak absolute values, including DC bias,

less than 110mVpeak

4) Signal peak absolute values, including DC bias,

less than 1100mVpeak

VFD AC Voltage :

Range Resolution 1)

Accuracy

10Hz ~ 45Hz

45Hz ~ 200Hz

0.1

600.0V

±(4.0%rdg + 5dgts)

±(2.5%rdg + 5dgts)

200Hz ~ 440Hz

0.1600.0V 2)

±(9.0%rdg + 5dgts)

Input impedance: 10MW, 110pF nominal

1) Unspecified for fundamental frequency > 440Hz

2) Accuracy linearly decreases from 2.5% + 5d @200Hz to

9.0% + 5d @440Hz

Range Resolution Accuracy

DC Voltage :

0.0160.00mV ±(0.2%rdg + 3dgts)

Input impedance: 10MW, 110pF nominal

600.0mV

6 000V.

60.00V

60.00mV

600.0V

1000V

0.1

0.001

0.01

0.1

±(0.1%rdg + 2dgts)

±(0.2%rdg + 3dgts)

Ohms :

Range Resolution Accuracy

0.01

60.00W2) ±(0.5%rdg + 5dgts)

600.0W

6 000k. W

60.00kW

600.0kW

6.000 3)

60.00M 4)

0.1

0.001

0.01

0.1

0.001

0.01

±(0.2%rdg + 2dgts)

±(1%rdg + 3dgts)

±(0.2%rdg + 3dgts)

±(0.3%rdg + 2dgts)

5)6)

±(1.5%rdg + 6dgts)

1) Open Circuit Voltage: 1.7VDC typical

2) Specified assumes input lead resistance been offset by

REL or Shrt (short) feature

3) Constant Test Current: 0.2µA Typical

4) Constant Test Current: 0.02µA Typical

5) Add 1% @ >20MW

6) Add 2% @ operation temperature >35°C

Audible Continuity Tester

Audible threshold: between 20W and 350W

Response time: < 30ms

Diode Tester

Test

Current

Open Circuit

Voltage

AccuracyResol.Range

2.700V 0.4mA < 2.8 VDC

±(1.5%rdg + 4dgts)

0.001

Capacitance :

Range Resolution 1)

Accuracy

2.000µF

20.00µF

200.0µF

2000µF

20.00mF

±(1.5%rdg + 5dgts)

±(5%rdg + 5dgts)

0.001

0.01

0.1

0.01

1) Accuracies with film capacitor or better

2) Specified from 0.200µF

Temperature :

Range 1)

Accuracy

1% + 2°C

-40.0°C to 0.0°C

0.0 C to 50.0 C° °

50.0 C to 537.0 C° °

-40.0 F to 32.0 F° °

32.0 F to 122.0 F° °

122.0 F to 999.0 F° °

2.2 C°

1% + 2 C°

1% + 3.6 F°

4 F°

1% + 3.6 F°

1) Accuracies assume meter interior has the same temperature

of the ambient (isothermal stage) for a correct junction voltage

compensation. Allow enough time to reach the isothermal

stage for a significant change of ambient temperature.

It can take up to an hour for changes > 5°C.

2) Type-K thermocouple range & accuracy not included

DC current :

Range Resolution Accuracy

1)2)

600.0mA

±(0.2%rdg + 4dgts)

0.1

0.01

0.1

0.001

Burden Voltage

6.000A

10.00A

60.00mA

6000 A µ

600.0 A µ

0.01

±(0.2%rdg + 2dgts)

±(0.2%rdg + 4dgts)

±(0.3%rdg + 3dgts)

±(0.5%rdg + 4dgts)

±(0.7%rdg + 2dgts)

0.2mV / Aµ

3mV / Am

30mV / A

1) A/mA DC accuracies will be affected by extreme interior

temperatures of the meter. For rated accuracies, allow

6 to 20 minutes cool down interval after measuring A-currents

of 3 to 10A continuously.

Tabla de contenidos

Otros manuales de Multímetro de Kusam-meco

Kusam-meco

Kusam-meco KM 525 Manual de usuario

Kusam-meco

Kusam-meco KM 5040-T Manual de usuario

Kusam-meco

Kusam-meco KM 6030 Manual de usuario

Kusam-meco

Kusam-meco M3511A Manual de usuario

Kusam-meco

Kusam-meco KM 2777 Manual de usuario

Kusam-meco

Kusam-meco 306 Manual de usuario

Kusam-meco

Kusam-meco KM-459 Manual de usuario

Kusam-meco

Kusam-meco KM 857 Manual de usuario

Kusam-meco

Kusam-meco 405 Manual de usuario

Kusam-meco

Kusam-meco 5040 Manual de usuario

Kusam-meco

Kusam-meco KM 2778 Manual de usuario

Kusam-meco

Kusam-meco KM 829 Manual de usuario

Kusam-meco

Kusam-meco KM 878 Manual de usuario

Kusam-meco

Kusam-meco 801-L Manual de usuario

Kusam-meco

Kusam-meco 2772 Manual de usuario

Kusam-meco

Kusam-meco KM 839 Manual de usuario

Kusam-meco

Kusam-meco KM 805s Manual de usuario

Kusam-meco

Kusam-meco KM 520B Manual de usuario

Kusam-meco

Kusam-meco 8010 Manual de usuario

Kusam-meco

Kusam-meco 603 Manual de usuario

Kusam-meco

Kusam-meco 2754A Manual de usuario

Kusam-meco

Kusam-meco M3500A Manual de usuario

Kusam-meco

Kusam-meco KM 829 Manual de usuario

Kusam-meco

Kusam-meco KM 8045 Manual de usuario

Manuales populares de Multímetro de otras marcas

Agilent Technologies

Agilent Technologies 34420A Manual de usuario

Fluke

Fluke 83 Manual de usuario

Hameg

Hameg HM 8012 Manual de usuario

Mastech

Mastech MY70 Manual de usuario

Steren

Steren MUL-300 Manual de usuario

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manual de usuario

PeakTech

PeakTech 4000 Manual de uso y cuidado

YOKOGAWA

YOKOGAWA 90050B Manual de usuario

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manual de usuario

Fluke

Fluke 8846A Manual de operación y mantenimiento

Tempo Communications

Tempo Communications MM200 Manual de usuario

Elenco Electronics

Elenco Electronics CM-1555 Manual de usuario

Mastech

Mastech MS8238C Manual de usuario

SDAR

SDAR 830A, 830B, 830D, 830C Manual de usuario

RS PRO

RS PRO RS-9519BT Manual de usuario

BGS technic

BGS technic 8890 Manual de usuario

Amprobe

Amprobe Hexagon 60 Manual de usuario