KTM 85 SX 2017 Manual

SETUP INSTRUCTIONS 2017

85 SX

Art. no. 3213592en

INTRODUCTION 1

*3213592en*

3213592en

09/2016

INTRODUCTION

The work described in these setup instructions must be performed before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make changes in the interest

of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop are not specified here. It

is assumed that the work will be performed by a fully trained mechanic.

All specifications are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right to modify or delete technical specifications,

prices, colors, forms, materials, services, designs, equipment, etc., without prior notice and without specifying reasons, to adapt these to

local conditions, as well as to stop production of a particular model without prior notice. KTM accepts no liability for delivery options, devi-

ations from illustrations and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that does not

belong to the regular scope of supply.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission of the copyright owner.

ISO 9001(12 100 6061)

According to the international quality management standard ISO 9001, KTM uses quality assurance processes that lead to

the maximum possible quality of the products.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

5230 Mattighofen, Austria

This document is valid for the following models:

85 SX 19/16 (F6001Q9)

85 SX 17/14 (F6001Q8)

1 MEANS OF REPRESENTATION 2

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Denotes a voltage measurement.

Denotes a current measurement.

Denotes a resistance measurement.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Identifies a proprietary name.

Name®Identifies a protected name.

Brand™ Identifies a trademark.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which are explained

in the glossary.

2 SETUP 3

2.1 Unpacking and setting up the vehicle

M00075-11

–Remove the box and the plastic packaging.

Info

An assistant prevents the motorcycle from falling over.

To avoid damaging the motorcycle during the setup, leave the protective

film on the vehicle until you have finished.

–Remove the separate enclosure and unpack it. Check that the scope of supply is

complete on the basis of the enclosed packing list.

402050-01

–Have a lift stand available.

Lift stand (78929955100)

–Together with an assistant, take the vehicle off the palette.

–Position the vehicle on a lift stand.

–Check the vehicle for transport damage.

201937-10

–Remove the tension belt.

The fork rebounds.

–Remove screw and wheel spindle. Lift the front wheel into the fork, position it,

and insert the wheel spindle.

–Mount and tighten the screw of the wheel spindle.

Guideline

Screw, front wheel spindle M20x1.5 35 Nm

(25.8 lbf ft)

201938-10

–Position the fender. Mount and tighten the screws.

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

L02337-01

–Unpack the shock absorber.

–Position the shock absorber. Mount and tighten the screws.

Guideline

Screw, top shock absorber M12 60 Nm

(44.3 lbf ft)

Loctite®2701™

Screw, bottom shock

absorber

M12 60 Nm

(44.3 lbf ft)

Loctite®2701™

The longer screw is used at the bottom.

V00031-10

–Position the handlebar.

Info

Make sure the cables and wiring are positioned correctly.

–Position the handlebar clamps. Mount and tighten the screws evenly.

Guideline

Screw, handlebar clamp M8 20 Nm

(14.8 lbf ft)

2 SETUP 4

Info

The markings on the handlebar should be at the center of the handlebar

clamps.

Keep the gap widths equal when tightening.

201941-10

–Position the handlebar cushion and secure with cable ties.

201942-10

–Remove screw with the guide from the start number plate.

–Position the start number plate. Mount and tighten screw .

Guideline

Remaining screws, chassis M6 10 Nm (7.4 lbf ft)

Info

Ensure the holding lugs engage in the fender.

–Position the brake line and guide. Mount and tighten screw .

L02365-01

–Connect the fuel line to the fuel tap.

800042-10

–Mount the footrests with the springs and pins. Secure the pins using the washers

and cotter pins.

Pliers for footrest spring (58429083000)

201944-10

–Take the vehicle off the work stand.

–Operate the hand brake lever several times until the brake linings are seated cor-

rectly against the brake disc.

–Activate the front brake and compress the fork a number of times forcefully to align

the fork legs.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

–Refuel. ( p. 7)

–Prepare the vehicle according to the specifications in the KTM Dealer.net for han-

dover to the customer.

3 WORK 5

3.1 Raising the motorcycle with the lift stand

Note

Danger of damage The parked vehicle can roll away or fall over.

–Park the vehicle on a firm and level surface.

401942-01

–Raise the motorcycle at the frame underneath the engine.

Lift stand (78929955100)

Neither wheel is in contact with the ground.

–Secure the motorcycle against falling over.

3.2 Removing the motorcycle from the lift stand

Note

Danger of damage The parked vehicle can roll away or fall over.

–Park the vehicle on a firm and level surface.

402001-10

–Remove the motorcycle from the lift stand.

–Remove the lift stand.

–To park the motorcycle, insert plug-in stand into the left side of the wheel spin-

dle.

Info

Remove the plug-in stand before riding.

3.3 Installing the front wheel

Warning

Danger of accidents Oil or grease on the brake discs reduces the braking effect.

–Always keep the brake discs free of oil and grease.

–Clean the brake discs with brake cleaner when necessary.

H00935-10

Main work

–Check the wheel bearing for damage and wear.

» If the wheel bearing is damaged or worn:

–Change the front wheel bearing.

–Clean and grease shaft seal rings and contact surface of the spacers.

Long-life grease ( p. 11)

–Insert the spacers.

S01171-11

–Clean and grease wheel spindle.

Long-life grease ( p. 11)

–Position the front wheel.

The brake linings are correctly positioned.

–Insert wheel spindle.

–Mount and tighten screw .

3 WORK 6

Guideline

Screw, front wheel spindle M20x1.5 35 Nm

(25.8 lbf ft)

–Operate the hand brake lever several times until the brake linings are seated cor-

rectly against the brake disc.

–Remove the motorcycle from the lift stand. ( p. 5)

–Operate the front brake and compress the fork a few times firmly.

The fork legs straighten.

–Tighten screws .

Guideline

Screw, fork stub M8 15 Nm

(11.1 lbf ft)

Finishing work

–Remove the motorcycle from the lift stand. ( p. 5)

3.4 Installing the front fender

H01366-10

–Position the front fender. Mount and tighten screws .

Guideline

Screw, front fender M6 10 Nm (7.4 lbf ft)

The holding lugs on the fender engage in the start number plate.

3.5 Installing the start number plate

H01365-11

–Position the start number plate. Mount and tighten screw .

Guideline

Start number plate screw M6 4 Nm (3 lbf ft)

The holding lugs on the fender engage in the start number plate.

–Position the brake line and clamp. Mount and tighten screw .

3.6 Opening the filler cap

Danger

Fire hazard Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–Switch off the engine for refueling.

–Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–If any fuel is spilled, wipe it off immediately.

–Observe the specifications for refueling.

3 WORK 7

Warning

Danger of poisoning Fuel is poisonous and a health hazard.

–Avoid skin, eye and clothing contact with fuel.

–Immediately consult a doctor if you swallow fuel.

–Do not inhale fuel vapors.

–In case of skin contact, rinse the affected area with plenty of water.

–Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–Change your clothing in case of fuel spills on them.

–Keep fuels correctly in a suitable canister, and out of the reach of children.

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

–Do not allow fuel to enter the groundwater, the soil, or the sewage system.

H01345-10

–Turn filler cap counterclockwise and lift it off.

3.7 Closing the filler cap

H01345-11

–Mount filler cap and turn it clockwise until the fuel tank is tightly closed.

Info

Run fuel tank breather hose without kinks.

3.8 Refueling

Danger

Fire hazard Fuel is highly flammable.

The fuel in the fuel tank expands when warm and can escape if overfilled.

–Do not refuel the vehicle in the vicinity of open flames or lit cigarettes.

–Switch off the engine for refueling.

–Make sure that no fuel is spilled; particularly not on hot parts of the vehicle.

–If any fuel is spilled, wipe it off immediately.

–Observe the specifications for refueling.

Warning

Danger of poisoning Fuel is poisonous and a health hazard.

–Avoid skin, eye and clothing contact with fuel.

–Immediately consult a doctor if you swallow fuel.

–Do not inhale fuel vapors.

–In case of skin contact, rinse the affected area with plenty of water.

–Rinse the eyes thoroughly with water, and consult a doctor in case of fuel contact with the eyes.

–Change your clothing in case of fuel spills on them.

3 WORK 8

Warning

Environmental hazard Improper handling of fuel is a danger to the environment.

–Do not allow fuel to enter the groundwater, the soil, or the sewage system.

–Switch off the engine.

–Open the filler cap. ( p. 6)

401522-10

–Fill the fuel tank with fuel up to measurement .

Guideline

Measurement of 35 mm (1.38 in)

Fuel tank capac-

ity, approx.

5.0 l

(1.32 US gal)

Super unleaded (98 octane) mixed

with 2-stroke engine oil (1:40)

( p. 10)

Engine oil, 2-stroke ( p. 10)

–Close the filler cap. ( p. 7)

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Motocicleta de KTM

KTM

KTM Adventure 1090 2017 Manual

KTM

KTM 450 Rally Factory Replica 2021 Manual de usuario

KTM

KTM 1190 RC8 R Track Manual de usuario

KTM

KTM 85 SX 19/16 Manual de usuario

KTM

KTM 2013 450 EXC EU Manual de usuario

KTM

KTM Freeride E-XC Manual de usuario

KTM

KTM 450 SX-F Manual de usuario

KTM

KTM 390 ADVENTURE EU 2022 Manual de usuario

KTM

KTM 350 XCF-W USA Manual de usuario

KTM

KTM 690 Enduro EU 2010 Manual

KTM

KTM 690 Enduro R EU 2015 Manual de usuario

KTM

KTM 1290 Super Adventure Manual de usuario

KTM

KTM 690 SMC USA 2010 Manual de usuario

KTM

KTM 250 SX Manual

KTM

KTM 350 EXC-F 2017 Manual de usuario

KTM

KTM 250 EXC Six Days TPI 2019 Manual de usuario

KTM

KTM 150 XC-W 2023 Manual de usuario

KTM

KTM 150 SX 2021 Manual

KTM

KTM 350 SX-F EU 2014 Manual

KTM

KTM 1190 Adventure R EU Manual de usuario

KTM

KTM 250 EXC-F 2016 Manual

KTM

KTM 450 SX-F Manual de usuario

KTM

KTM 2001 50 JR ADVENTURE Guía del usuario

KTM

KTM 390 Adventure 2020 Manual de usuario

Manuales populares de Motocicleta de otras marcas

OHVALE

OHVALE GP-0 Manual de lista de piezas

Yamaha

Yamaha Star XV19CTSZ 2009 Manual de usuario

HYOSUNG

HYOSUNG ST7 Manual de usuario

Husqvarna

Husqvarna FC 250 2016 Manual de usuario

Ducati

Ducati SCRAMBLER 800 Manual de instrucciones

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Manual de usuario

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Manual de usuario

Yamaha

Yamaha 2006 YZF-R1V Manual de usuario

Fantic

Fantic Enduro 125 Manual de usuario

Ducati

Ducati Supersport 750 desmodue Manual de usuario

MV Agusta

MV Agusta 2008 F4 312RR 1078 Manual de instrucciones

Yamaha

Yamaha XVS650A Manual de usuario

Yamaha

Yamaha YZF-R6T(C) Manual

Ducati

Ducati 748 monoposto strada Manual de usuario

ATK

ATK 1988 250 Manual de usuario

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Manual de usuario

Triumph

Triumph Thunderbird Manual de usuario

Yamaha

Yamaha 2006 FJR1300A Manual de usuario