KTI KS-1080 Manual de usuario
-1-
DOC.041215
KS-1080
Installation Guide
-2-
(C) 2002 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in
any form or by any means or used to make any directive work (such as translation or transformation)
without permission from KTI Networks Inc.
KTI Networks Inc. reserves the right to revise this documentation and to make changes in content
from time to time without obligation on the part of KTI Networks Inc. to provide notification of such
revision or change.
For more information, contact:
United States KTI Networks Inc.
P.O. BOX 631008
Houston, Texas 77263-1008
Phone: 713-2663891
Fax: 713-2663893
E-mail: [email protected]
URL: http://www.ktinet.com/
International Fax: 886-2-26983873
E-mail: [email protected]
URL: http://www.ktinet.com.tw/
-3-
The information contained in this document is subject to change without prior notice. Copyright (C). All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
WARNING:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and if not
installed and used in accordance with the instruction manual may cause harmful interference in which case the user will be
required to correct the interference at his own expense.
NOTICE:
(1) The changes or modifications not expressively approved by the party responsible for compliance could void the user's
authority to operate the equipment.
(2) Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.
CISPR A COMPLIANCE:
This device complies with EMC directive of the European Community and meets or exceeds the following technical standard.
EN 55022 - Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment.
This device complies with CISPR Class A.
WARNING: This is a Class A product. In a domestic environment this product may cause radio interference in which case the
user may be required to take adequate measures.
CE NOTICE
Marking by the symbol indicates compliance of this equipment to the EMC directive of the European Community. Such
marking is indicative that this equipment meets or exceeds the following technical standards:
EN 55022: Limits and Methods of Measurement of Radio Interference characteristics of Information Technology Equipment.
EN 50082/1:Generic Immunity Standard -Part 1: Domestic Commercial and Light Industry.
EN 60555-2: Disturbances in supply systems caused by household appliances and similar electrical equipment - Part 2:
Harmonics.
-4-
Table of Contents
1. Introduction ...............................................................................................................6
1.1 Features ................................................................................................................................................. 7
1.2 Front and Rear Panels ........................................................................................................................... 7
1.3 Specifications ......................................................................................................................................... 8
2. Installation ............................................................................................................... 11
2.1 Unpacking ............................................................................................................................................ 11
2.2 Safety Cautions .................................................................................................................................... 11
2.3 Mounting the Switch ............................................................................................................................. 11
2.4 AC Power Supply .................................................................................................................................. 12
2.5 Making UTP Connections .................................................................................................................... 12
2.6 Making Power over Ethernet UTP Connections ..................................................................................12
2.7 Making Fiber Connections ................................................................................................................... 13
2.8 Configuring IP Address and Access Settings for the Switch............................................................... 14
2.9 Reset Button......................................................................................................................................... 14
2.10 LED Indicators.................................................................................................................................... 14
3. Advanced Functions...............................................................................................15
3.1 QoS Function ........................................................................................................................................ 15
3.1.1 Priority Level ...................................................................................................................................... 15
3.1.2 Egress Service Policy........................................................................................................................ 15
3.1.3 Packet Priority Classification............................................................................................................. 15
3.1.3.1 Port-based Priority Setting (per port setting).................................................................................. 16
3.1.3.2 802.1p Classification (per port setting) ......................................................................................... 16
3.1.3.3 DSCP Classification (per port setting)........................................................................................... 16
3.1.3.4 IP Network Address Classification ................................................................................................ 17
3.1.4 Other QoS Settings............................................................................................................................ 17
3.2 VLAN Function ...................................................................................................................................... 18
3.2.1 VLAN Operation ................................................................................................................................. 18
3.2.2 Ingress Rules.................................................................................................................................... 19
3.2.2.1 802.1Q Tag Aware VLAN Mode (global setting).............................................................................19
3.2.2.2 Ingress Member Filtering (global setting) ..................................................................................... 19
3.2.2.3 Unmatched VID Filtering (per port setting) .................................................................................... 19
3.2.3 VLAN Group Mapping ........................................................................................................................ 20
3.2.4 Packet Forwarding under VLAN ........................................................................................................ 20
3.2.5 Egress Tagging Rules ...................................................................................................................... 20
3.2.5.1 Egress Tag Rule (per port setting)................................................................................................. 20
3.2.5.2 Null VID Replacement (per port setting) ........................................................................................ 21
3.2.6 Summary of VLAN Function .............................................................................................................. 21
3.3 Power over Ethernet Function .............................................................................................................. 22
3.3.1 PoE Specifications ............................................................................................................................ 22
3.3.2 PoE PSE Capabilities ....................................................................................................................... 22
3.3.3.3 PoE Management functions........................................................................................................... 23
3.3.4 Notices for PoE Installation............................................................................................................... 23
4. Software Management ...........................................................................................24
4.1 Telnet Management Interface............................................................................................................... 24
-5-
4.2 IP Menu ................................................................................................................................................. 25
4.3 SNMP Menu .......................................................................................................................................... 26
4.4 Port Config............................................................................................................................................ 27
4.5 Administrator ........................................................................................................................................ 28
4.5.1 Administrator -> VLAN Settings......................................................................................................... 28
4.5.2 Administrator -> QoS Settings .......................................................................................................... 32
4.5.3 Administrator -> PoE Settings........................................................................................................... 35
4.6 Restore Default Values ........................................................................................................................ 36
4.7 Security Manager .................................................................................................................................. 36
4.8 Update Firmware.................................................................................................................................. 36
4.9 Reboot System ..................................................................................................................................... 37
4.10 Exit ...................................................................................................................................................... 37
5. Web Management ...................................................................................................38
5.1 Start Browser Software and Making Connection ................................................................................. 38
5.2 Login to the Switch Unit........................................................................................................................ 38
5.3 Port Status Menu .................................................................................................................................. 40
5.4 Administrator ........................................................................................................................................ 41
5.4.1 Basic Menu ........................................................................................................................................ 41
5.4.2 Port Controls ..................................................................................................................................... 44
5.4.3 VLAN Controls ................................................................................................................................... 45
5.4.4 QoS Controls ..................................................................................................................................... 48
5.4.5 PoE Controls ..................................................................................................................................... 51
5.4.6 Security Manager ............................................................................................................................... 52
5.4.7 Image Refresh Time ......................................................................................................................... 52
5.4.8 Update Firmware............................................................................................................................... 53
5.4.9 Restore Default ................................................................................................................................. 53
5.4.10 Reboot System................................................................................................................................ 53
6. SNMP Management ................................................................................................54
6.1 MIB Objects........................................................................................................................................... 54
6.2 SNMP Traps ......................................................................................................................................... 54
Appendix. Factory Default Settings ..........................................................................55
-6-
1. Introduction
The switch provides six 10/100Mbps Fast Ethernet switched copper ports and two 100Mbps fiber port
slots. The copper ports support auto-negotiation and auto MDI/MDI-X for easy making connections to
Fast Ethernet devices.
The switch also provides the following advantages:
Fiber Connections
The 100Mbps fiber port slots can accommodate a variety of optional fiber modules for multimode and
single mode fiber connections.
Power over Ethernet (PoE)
Four of the copper ports are equipped with IEEE standard Power over Ethernet (PoE) function. The
PoE function enables the ports to deliver DC power to the remote connected devices which are ca-
pable to receive operating power from the network cable. This allows to extend the network connec-
tions to a locations where the power line is difficult to reach.
Quality of Service (QoS)
For more multimedia applications over IP such as voice and video, the switch provides a very powerful
QoS function which allows high priority data to be forwarded with best performance. The provided
packet priority classifications are powerful and flexible to meet different application needs. The classi-
fications can be port-based, 802.1p-based, IP-DSCP-based, or IP network address based.
Virtual LAN (VLAN)
For VLAN environments, the switch provides a flexible VLAN mechanism to support eight different
VLANs at the same time. Each VLAN can be identified by full 12-bit VLAN ID value. Together with
powerful ingress filtering rules and egress tagging rules, the switch allows LAN administrators to build
a VLAN network easily.
Management
For configuration and management purpose, the switch is featured with the following management
interfaces:
• Telnet software over TCP/IP network
• SNMP manager software over TCP/IP network
• Web browser software from Internet or Intranet over TCP/IP network
• SNMP trap hosts from Internet or Intranet over TCP/IP network
-7-
1.1 Features
• Fast Ethernet switch with 6 10/100TX TP ports and 2 100FX slots
• Auto MDI/MDI-X detection on all TP ports
• Auto-negotiation capable on all TP ports
• Port configuration control function
• IEEE 802.3af PoE PSE function on 4 TP ports
• 100FX slots support wide range of fiber options
- ST, SC, MT-RJ, VF-45, LC, single WDM SC
- Multi-modefiber, Single mode duplex fiber, Single fiber
- Short reach, medium reach, and long reach fiber connections
• Far End Fault function on FX ports
• Back pressure flow control for half duplex operation
• IEEE 802.3x flow control for full duplex operation
• Broadcast storm protection function
• Software management : Web, SNMP, telnet, SNMP trap
• QoSfunction
• VLAN function
• Provides comprehensive LED indication
• Support desktop, wall, and 19-inch rack mounting
1.2 Front and Rear Panels
The front panel and rear panel of the switch are shown as follows:
-8-
1.3 Specifications
Network Ports
TP Copper Ports 6 fixed 10/100TX Twisted Pair Ports (P1 - P6)
PoE Function Ports 4 of the 6 10/100TX ports with configurable PoE PSE function (P1 - P4)
FX Ports 2 100FX fiber slots
10/100TX Twisted Pair Port (TP Port P1 ~ P6)
Compliance IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX
Connectors Shielded RJ-45 jacks
Pin assignments Auto MDI/MDI-X detection
Configuration Auto-negotiation capable or forced mode
Transmission rate 10Mbps, 100Mbps
Duplexsupport Full/Halfduplex
Flowcontrol IEEE 802.3x pause frame base for full duplex operation
Back pressure for half duplex operation
Network cable Cat.5 UTP
PoE function P1 ~ P4 with optional PoE PSE function
100FX Fiber Slots (FX Ports)
Compliance IEEE 802.3u 100BASE-FX
Configuration Forced 100Mbps, Full duplex (factory default)
Transmission rate 100Mbps
Far end fault function Capable to receive FEFI (far end fault indication) signal
Capable to send FEFI signal when Rx link failure detected
Flowcontrol IEEE 802.3x pause frame base for full duplex operation
Back pressure for half duplex operation
Optionalmodules Refer to Installation guide for optional fiber modules
Network cables MMF 50/125mm 60/125mm, SMF 9/125mm
Eye safety IEC 825 compliant
PoE Function
Compliance IEEE 802.3af
PoE PSE ports P1 ~ P4
PSE Pinout Alternative B
RJ-45 Pin 4,5 - Positive Vport
RJ-45 Pin 7,8 - Negative Vport
PSE level Class 0 for all ports
Maximumoutput 15.4W per PoE port
Port Output voltage Vport = 48VDC
-9-
Control Enable/Disable via software control
Monitor Power status, power voltage, power current, watts
Switch Functions
Forwarding & filtering Non-blocking, full wire speed
Switchingtechnology Store and forward
Maximum packet length 1536 bytes
Broadcast storm 64 consecutive broadcast packets in 800ms
Protection by dropping broadcast storm packets
VLAN function Port-based VLAN & IEEE 802.1Q Tag-based VLAN
QoSfunction Port-based, 802.1p-based, IP DSCP-based, IP address-based
Port control Port configuration control via software management
Software Management Functions
Interfaces Web, telnet, SNMP MIB-II & private MIB, Traps
Management objects Port configuration control and status
Username and password settings
IP, SNMP related settings
VLAN function settings
QoS function setting
PoE function setting and status
Port Configuration Control Function
Configuration P1 ~ P6
Port control function Port TX/RX - enable, disable
Port mode - Auto (auto-negotiation), Forced
Port speed - 100Mbps, 10Mbps
Port duplex - full, half
Port Status Port mode, link, speed, duplex
VLAN Function
VLAN groups 8 groups
GlobalSettings VLAN Mode - Port-based, 802.1Q Tag Aware VLAN
Ingress member port filtering mode
VLAN Group Settings 12-bit VLAN ID
Member ports
Per Port Settings Default VLAN group index
Unmatched VID packet ingress filtering mode
Egress Tagging Rules
-10-
Null VID replacement mode (Egress)
QoS Function
Priority level 2, High priority and Low priority
Priorityclassifications Port-based priority mode (per port setting)
802.1p classification (per port setting)
Default IP DSCP classification (per port setting)
2 user defined DSCP match classification (global)
2 user defined IP network address match classification (global)
802.1pprioritytag Threshold tag value setting for high priority (0 ~ 7)
Egress service policy Weighted round robin ratio : 16:1, always high first, 8:1, 4:1
LED Indicators
System Power status
Diag Diagnostic status
Per 10/100TX port TP port link status, 100M/10M status, duplex status
Per 100FX port FX port link status
Per PoE port PoE power status
Power Characteristics
Power supply Rating AC input : 100~240V / 50-60Hz
Input voltage range 90VAC ~ 264VAC
Input frequency range 47 ~ 63Hz
Power consumption 100W max. @AC110V (All PoE ports output maximum power.)
Environmental
Operating temperature -5oC ~ 40oC
Storage temperature -20oC ~ 85oC
Relativehumidity 5% ~ 95% noncondensing
Physical Characteristics
Dimension 295 x 160 x 43 mm (L x D x H)
Weight 1.5 Kg
Mounting Desktop, Wall mountable, 19-inch rack mountable
Electrical Approvals
FCC Part 15 rule Class A
CE EMC, CISPR22 Class A
Tabla de contenidos
Otros manuales de Cambiar de KTI
KTI
KTI KS-115FM-V Manual de usuario
KTI
KTI KGS-810F Manual de usuario
KTI
KTI KGS-2404-B Manual de usuario
KTI
KTI KGS-510F Manual de usuario
KTI
KTI KGS-1620 Manual de usuario
KTI
KTI KGS-3120 Manual de usuario
KTI
KTI KS-2300 Manual de usuario
KTI
KTI KCF-121 Manual de usuario
KTI
KTI KGS-510F Manual de usuario
KTI
KTI KGS-612F Manual de usuario
