KTI Networks KFC-241 Manual de usuario
KFC-241
Industrial
10/100BASE-T to 100BASE-FX
Media Converters
Installation Guide
DOC.110516
-1-
(C) 2011 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced in any form
or by any means or used to make any directive work (such as translation or transformation) without permission
from KTI Networks Inc.
KTI Networks Inc. reserves the right to revise this documentation and to make changes in content from time to
time without obligation on the part of KTI Networks Inc. to provide notification of such revision or change.
For more information, contact:
United States KTI Networks Inc.
P.O. BOX 631008
Houston, Texas 77263-1008
Phone: 713-2663891
Fax: 713-2663893
URL: http://www.ktinet.com/
International Fax: 886-2-26983873
URL: http://www.ktinet.com.tw/
-2-
The information contained in this document is subject to change without prior notice.
Copyright (C) All Rights Reserved.
TRADEMARKS
Ethernet is a registered trademark of Xerox Corp.
FCC NOTICE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) This device must accept any interference received,
including the interference that may cause undesired operation.
CE NOTICE
Marking by the symbol “CE” indicates compliance of this equipment to the EMC directive of the European
Community. Such marking is indicative that this equipment meets or exceeds the following technical
standards:
EMC Class A
EN 61000-6-3:2007 IEC 61000-6-3:2007
EN 55022:2006/A1:2007 CISPR 22:2005 Class A
EN 61000-3-2:2006 IEC 61000-3-2:2005
EN 61000-3-3:2008 IEC 61000-3-3:2008
EN 55024:1998/A1:2001/A2:2003 CISPR 24:1997
EN 61000-4-2:2009 IEC 61000-4-2:2008
EN 61000-4-3:2006/A1:2008 IEC 61000-4-3:2006
EN 61000-4-4:2004 IEC 61000-4-4:2004
EN 61000-4-5:2006 IEC 61000-4-5:2005
EN 61000-4-6:2009 IEC 61000-4-6:2008
EN 61000-4-8:1993/A1:2001 IEC 61000-4-8:1998/A1:2000
EN 61000-4-11:2004 IEC 61000-4-11:2004
-3-
-4-
Table of Contents
1. Introduction......................................................................................................................................................5
1.1 Features.................................................................................................................................6
1.2 Specifications.........................................................................................................................7
1.3 Model Specifications............................................................................................................11
1.4 Special Functions.................................................................................................................11
2. Installation......................................................................................................................................................13
2.1 Unpacking............................................................................................................................ 13
2.2 Safety Cautions.................................................................................................................... 13
2.3 DIN-Rail Mounting................................................................................................................14
2.4 Mounting on a Plane Surface...............................................................................................18
2.5 Applying Power.................................................................................................................... 21
2.6 Making Copper Port Connection.......................................................................................... 22
2.7 Making Fiber Port Connection..............................................................................................23
3. LED Indicators...............................................................................................................................................24
3.1 States and Indications.......................................................................................................... 24
Appendix. On-board Configuration.................................................................................................................25
1. Introduction
The industrial 10/100BASE-TX to 100BASE-FX media converter series provides industrial strength Ethernet
copper-to-fiber media conversion, allowing for 10Base-T-100Base-FX or 100Base-TX-100Base-FX over
multi-mode or optional single-mode fiber optical media.
In addition to the basic media conversion functions, the converters also provide some special functions to
enhance the flexibility for wide application needs as follows:
AUTO-NEGO FUNCTION
The copper port is featured this function which performs a negotiation process for the speed and duplex
configuration with the connected device automatically when each time a link is being established.
AUTO-CROSS FUNCTION
The copper port is featured this function that allows to auto-detect the twisted-pair signals and adapts itself to
form a valid MDI to MDI-X connection with the remote connected device automatically.
FAR END FAULT FUNCTION
The fiber port is facilitated with this function, which conforms to IEEE 802.3u 100BASE-FX specifications.
When the port detects a link failure on its receiving circuitry, it will send out an FEFI (Far End Fault Indication)
signal to the remote connected device to indicate a remote fault is detected. It also is capable to receive FEFI
signal sent from the remote link partner. Upon receiving an FEFI signal, it indicates a link failure occurred on
the transmitting path. This function allows the converter to report a fiber link fault even when a link failure
occurred on transmitting fiber cable.
SMART-FORWARDING FUNCTION
-5-
The converter uses store-and-forward mechanism for packet forwarding normally when both media ends
-6-
operate at different speed, but switches to direct conversion automatically and with the least latency when both
media ends operate at the same speed.
LINK FAULT PASS THROUGH FUNCTION
The function allows the link fault status passes through from one media end to another media end transparently.
INDUSTRIAL ENHANCEMENT
For industrial environment, the converters are designed with the following enhanced features exceeding that of
commercial media converters:
zHigh and wide operating Temperature
zWide operating voltage range for DC power input
zPower input interfaces: Terminal block for industrial power supply and DC jack for typical power adapter
zDIN-Rail mounting support for industrial enclosure
zScrew plane mounting support for industrial enclosure
zIndustrial-rated Emission and Immunity performance
1.1 Features
zConvert speed and media type
zSupport full wire speed conversion
zSupport 10Mbps and 100Mbps speed on the copper connections
zAuto MDI/MDI-X detection function on the copper port
zAuto-negotiation function on the copper port
zLink fault pass through function
zPlug and play with no complicated configuration
zTransparent conversion to 802.1Q VLAN tagged packets
zFar End Fault function on the fiber port
zSupport wide range of fiber options on the fiber port
zLow power consumption
zTwo power interface types: screw terminal block and DC jack
zWide operating voltage input range
zSupport DIN rail mounting
zSupport plane mounting
zHigh and wide operating temperature range
zIndustrial-rated Emission and Immunity performance
1.2 Specifications
This figure shows the important components of the converters:
Model KFC-241-L
Model KFC-241-H
-7-
-8-
Copper Port (Twisted-Pair Interface)
Connector Shielded RJ-45
Pin Assignments Auto MDI/MDI-X detection
Signal Compliance IEEE 802.3 10BASE-T, 802.3u 100BASE-TX
Data Speed 10Mbps or 100Mbps
Duplex Mode Half-duplex or Full-duplex
Configuration Auto-negotiation capable for speed and duplex
Cable Types 10Mbps - Category 3, 4, or 5 UTP
100Mbps - Category 5 UTP
Supported Link Distance Up to 100 meters
FX Port (Fiber Optic Interface)
Signal Compliance IEEE 802.3u 100BASE-FX
Connector SC, ST, or Single SC (model dependent)
Data Speed 100Mbps
Duplex Mode Full-duplex and optional half duplex
Cable Types Multimode (MMF) - 50/125, 62.5/125μm
Single mode (SMF) - 9/125μm
Supported Link Distance MMF up to 2km
SMF, single SMF (model dependent)
Eye Safety compliance IEC825 Class 1
DC Power Input
KFC-241-L
Interfaces Screw-type Terminal Block 3P (TB-3P)
DC Jack (-D 6.3mm /+D 2.0mm)
Operating Input Voltages +4.5VDC ~ +50VDC
Power Consumption 1.6W @+7.5VDC input
1.6W @+12VDC input
2W @+48VDC input
KFC-241-H
Interface Screw-type Terminal Block 3P (TB-3P)
Operating Input Voltage +110VDC
Power Consumption 2.9W @+110VDC input
-9-
LED Indicators
LED Name Display function
PWR Power status
LINK Link status
100M Copper port operating speed
OL Fiber port optical link
Mechanical
Dimension (base) KFC-241-L - W 34mm x D 49mm x H 56mm
KFC-241-H - W 45.5mm x D 49mm x H 56mm
Weight KFC-241-L - 132g
KFC-241-H - 164g
Housing Enclosed metal with no fan
Mounting Support DIN-rail mounting, Plane mounting
Environmental
Operating Temperature Ambient -20oC ~ 70oC
Storage Temperature -30oC ~ 85oC
Relative Humidity 5% ~ 90%
Basic Information
Forwarding Throughput Full wire speed at 100M full duplex
10Mbps - 14,880pps at 64-byte packets
100Mbps - 148,800pps at 64-byte packets
Packet Types Transparent and no modification for
- IEEE 802.3 standard packets
- IEEE 802.1Q VLAN tagged packets
Packet Length Up to 1600 bytes under 100Mbps-10Mbps conversion
No limit under 100Mbps to 100Mbps conversion
Flow Control Back-pressure for half-duplex mode
802.3x pause-frame base for full duplex mode
Certificate
FCC Part 15 Class A
CE/EMC EMI EN50081-1 Class A
EMS EN55024
CE/LVD Safety EN 60950
-10-
EN 50081-1:
EN55022 CISPR Class B
EN61000-3-2 Device <75W
EN61000-3-3 Clause 5
EN 55024 Severity Level
IEC 61000-4-2 ESD Test Contact +/-6KV/Air +/-8KV
IEC 61000-4-3 RS Test Power/Data Ports Level 1, 2, 3
IEC 61000-4-4 EFT/Burst Test DC IN +/-1KV/Data Ports +/-0.5KV
IEC 61000-4-5 Surge Test DC IN +/-0.5KV/Data Ports +/-1KV
IEC 61000-4-6 CS Test DC IN Level 3
IEC 61000-4-8 PFMF Test Continuous, 100A/m, XY, 30 sec.
IEC 61000-4-11 Voltage Int. Dips Interruption 100% 250 periods
Dips 30% 25 periods
Dips 60% 0.5 period
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Convertidor de medios de KTI Networks
KTI Networks
KTI Networks KC-10TF Series Manual de usuario
KTI Networks
KTI Networks Modular Media Converter Center System... Manual de usuario
KTI Networks
KTI Networks KFC-200 Manual de usuario
KTI Networks
KTI Networks KC-10FM/T Manual de usuario
KTI Networks
KTI Networks KCD-400 Series Manual de usuario
KTI Networks
KTI Networks KTGC-221 Manual de usuario
KTI Networks
KTI Networks KC-351 Series Manual de usuario
KTI Networks
KTI Networks KSC-240 Manual de usuario
KTI Networks
KTI Networks KGC-320 Manual de usuario
KTI Networks
KTI Networks Modular Media Converter Center System... Manual de usuario
KTI Networks
KTI Networks 100BASE-TX Manual de usuario
KTI Networks
KTI Networks 10Base-T to 10Base-FL Media Converters... Manual de usuario
KTI Networks
KTI Networks KGC-352 Series Manual de usuario
KTI Networks
KTI Networks KC-10FM Manual de usuario
KTI Networks
KTI Networks KC-220FF-TSA Manual de usuario
KTI Networks
KTI Networks KSC-361 Manual de usuario
KTI Networks
KTI Networks KGC-301 Manual de usuario
KTI Networks
KTI Networks KGC-311 Series Manual de usuario
KTI Networks
KTI Networks KSC-200 Series Manual de usuario
KTI Networks
KTI Networks KGC-310 Manual de usuario
