KROHNE OPTISOUND 3010 C Manual de usuario

OPTISOUND 3010 C Quick setup guide

Ultrasonic Level Transmitter

Two-wire 4 … 20 mA/HART

Contents

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

Contents

1 For your safety ......................................................................................................................... 3

1.1 Authorised personnel ....................................................................................................... 3

1.2 Appropriate use................................................................................................................ 3

1.3 Warning about incorrect use............................................................................................. 3

1.4 General safety instructions............................................................................................... 3

1.5 Safety label on the instrument .......................................................................................... 3

1.6 EU conformity................................................................................................................... 4

1.7 NAMUR recommendations .............................................................................................. 4

2 Product description................................................................................................................. 5

2.1 Conguration.................................................................................................................... 5

3 Mounting................................................................................................................................... 6

3.1 Mounting instructions ....................................................................................................... 6

4 Connecting to power supply................................................................................................... 7

4.1 Connection procedure...................................................................................................... 7

4.2 Wiring plan, single chamber housing................................................................................ 8

4.3 Wiring plan, double chamber housing .............................................................................. 8

5 Set up with the display and adjustment module .................................................................. 9

5.1 Insert display and adjustment module.............................................................................. 9

5.2 Setup steps ...................................................................................................................... 9

5.3 Menu schematic............................................................................................................. 12

6 Supplement ............................................................................................................................ 14

6.1 Technical data ................................................................................................................ 14

Information:

This quick setup guide enables quick setup and commissioning of

your instrument.

Youcanndfurtherinformationinthecorresponding,comprehensive

operating instructions as well as in the Safety Manual for instruments

withSILqualication.

Operating instructions OPTISOUND 3010 C - Two-wire

4 … 20 mA/HART: Document-ID 30503

Editing status of the quick setup guide: 2019-09-25

1 For your safety

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

1 For your safety

1.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

Duringworkonandwiththedevice,therequiredpersonalprotective

equipment must always be worn.

1.2 Appropriate use

OPTISOUND3010Cisasensorforcontinuouslevelmeasurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter " Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

1.3 Warning about incorrect use

Inappropriateorincorrectuseofthisproductcangiverisetoapplica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

oradjustment.Damagetopropertyandpersonsorenvironmental

contaminationcanresult.Also,theprotectivecharacteristicsofthe

instrument can be impaired.

1.4 General safety instructions

Thisisastate-of-the-artinstrumentcomplyingwithallprevailing

regulationsanddirectives.Theinstrumentmustonlybeoperatedina

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressiveorcorrosivemediathatcancauseadangeroussituation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tionalinstallationstandardsaswellasthevalidsafetyregulationsand

accidentpreventionrulesmustbeobservedbytheuser.

Forsafetyandwarrantyreasons,anyinvasiveworkonthedevice

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

Toavoidanydanger,thesafetyapprovalmarkingsandsafetytipson

thedevicemustalsobeobserved.

1.5 Safety label on the instrument

Thesafetyapprovalmarkingsandsafetytipsonthedevicemustbe

observed.

1 For your safety

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

1.6 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrumentwiththesedirectives.

The EU conformity declaration can be found on our homepage.

1.7 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

• NE 21 – Electromagnetic compatibility of equipment

• NE43–Signallevelforfaultinformationfrommeasuringtransduc-

ers

• NE53–Compatibilityofelddevicesanddisplay/adjustment

components

For further information see www.namur.de.

2 Product description

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

2 Product description

2.1 Conguration

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

• Instrument type

• Articleandserialnumberdevice

• Article number, documentation

• Technicaldata:Approvals,processtemperature,processtting/

material,signaloutput,voltagesupply,protection

Type label

3 Mounting

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

3 Mounting

3.1 Mounting instructions

The reference plane for the measuring range is the lower edge of the

transducer.

Make sure that a minimum distance from the reference plane - the

so-calleddeadzone,inwhichmeasurementisnotpossible-is

maintained.Theexactvalueofthedeadzoneisstatedinchapter"

Technical data".

Fig. 1: Minimum distance to the max. level

1 blocking distance

2 Reference plane

Mountthesensoratleast200mm(7.874in)awayfromthevessel

wall.

> 200 mm

Fig. 2: Mounting on round vessel tops

1 Reference plane

2 Vessel center or symmetry axis

Reference plane for

measuring range

Mounting

4 Connecting to power supply

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

4 Connecting to power supply

4.1 Connection procedure

Proceed as follows:

1. Unscrew the housing lid

2. Ifadisplayandadjustmentmoduleisinstalled,removeitbyturn-

ing it to the left

3. Loosencompressionnutofthecableglandandremoveblind

plug

4. Removeapprox.10cm(4in)ofthecablemantle,stripapprox.

1cm(0.4in)ofinsulationfromtheendsoftheindividualwires

5. Insert the cable into the sensor through the cable entry

6. Lifttheopeningleversoftheterminalswithascrewdriver(see

following illustration)

7. Insert the wire ends into the open terminals according to the wir-

ing plan

Fig. 3: Connection steps 6 and 7

8. Pressdowntheopeningleversoftheterminals,youwillhearthe

terminal spring closing

9. Check the hold of the wires in the terminals by lightly pulling on

them

10. Connect the shielding to the internal ground terminal, connect the

externalgroundterminaltopotentialequalisation

11. Tighten the compression nut of the cable entry gland. The seal

ring must completely encircle the cable

12. Screw the housing lid back on

Theelectricalconnectionisnished.

4 Connecting to power supply

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

4.2 Wiring plan, single chamber housing

I2C

Display

12 5678

Fig. 4: Wiring plan - single chamber housing

1 Voltage supply, signal output

4.3 Wiring plan, double chamber housing

I2C

Fig. 5: Wiring plan - double chamber housing

1 Voltage supply, signal output

Wiring plan

5 Set up with the display and adjustment module

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

5 Set up with the display and adjustment

module

5.1 Insert display and adjustment module

The display and adjustment module can be inserted into the sensor

andremovedagainatanytime.Itisnotnecessarytointerruptthe

voltagesupply.

Proceed as follows:

1. Unscrew the housing lid

2. Place the display and adjustment module in the desired position

ontheelectronics(fourpositionsin90°osetcanbeselected)

and turn to the right until it clicks into place.

3. Screw housing lid with inspection window tightly back on

Disassemblyiscarriedoutinreverseorder.

The display and adjustment module is powered by the sensor, an ad-

ditional connection is not necessary.

Fig. 6: Insert display and adjustment module in the single chamber housing

Note:

Ifyouintendtoretrottheinstrumentwithadisplayandadjustment

moduleforcontinuousmeasuredvalueindication,ahigherlidwithan

inspection glass is required.

5.2 Setup steps

1. Go to the menu " Basic adjustment"viathedisplayandadjust-

ment module.

Mount/dismount display

and adjustment module

Set parameters

5 Set up with the display and adjustment module

OPTISOUND 3010 C • Two-wire 4 … 20 mA/HART

62683-EN-210820

▶Basicadjustment

Display

Diagnostics

Service

Info

2. Carry out the adjustment in the menu items " Min. adjustment"

and " Max. adjustment".

Max.adjustment

100.00 %

1.000 m(d)

2.000 m(d)

Min. adjustment

0.00 %

5.000 m(d)

4.000 m(d)

3. Select in the menu item " Medium" the medium of your applica-

tion,forexample"Aqueous solution".

Medium

Liquid

4. Select in the menu item " Application"thevessel,theapplication

andthevesselform,forexample,"Storage tank".

Vessel shape

Storage tank

The sensor measures the distance from the sensor to the medium

surface.Forindicationofthereallevel,anallocationofthemeasured

distance to the percentage height must be carried out.

Theactuallevelisthencalculatedonthebasisoftheseentered

values.Atthesametime,theoperatingrangeofthesensorislimited

frommaximumrangetotherequestedrange.

Parameter adjustment

Otros manuales para OPTISOUND 3010 C

Tabla de contenidos

Otros manuales de Transmisor de KROHNE

KROHNE

KROHNE OPTITEMP TT 12 R Manual de usuario

KROHNE

KROHNE OPTIWAVE 500 Series Diagrama de cableado

KROHNE

KROHNE OPTISOUND 3010 C Manual de usuario

KROHNE

KROHNE OPTIBAR DP 3050 Manual de usuario

KROHNE

KROHNE OPTIWAVE 400 Series Diagrama de cableado

KROHNE

KROHNE OPTISOUND 3020 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3030 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3030 C Manual de usuario

KROHNE

KROHNE OPTIBAR 5060 Diagrama de cableado

KROHNE

KROHNE OPTISOUND3020 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3020 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3010 C Manual de usuario

KROHNE

KROHNE OPTIWAVE 6300 C Diagrama de cableado

KROHNE

KROHNE OPTISOUND 3020 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3010 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3010 C Manual de usuario

KROHNE

KROHNE OPTIBAR P 1010 Diagrama de cableado

KROHNE

KROHNE DR 400 Series Diagrama de cableado

KROHNE

KROHNE OPTIWAVE X500 Diagrama de cableado

KROHNE

KROHNE OPTISOUND 3020 Manual de usuario

KROHNE

KROHNE OPTIWAVE 1010 Diagrama de cableado

KROHNE

KROHNE OPTISOUND 3030 C Manual de usuario

KROHNE

KROHNE OPTISOUND 3010 C Manual de usuario

KROHNE

KROHNE OPTIBAR 5060 Diagrama de cableado

Manuales populares de Transmisor de otras marcas

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manual del propietario

Honeywell

Honeywell 5816WMBR Manual de usuario

Kamstrup

Kamstrup READy MTU Instrucciones de funcionamiento

Omega

Omega ZW Series Manual de usuario

ABB

ABB Field 264H Guía

Alinco

Alinco DJ-V17T Manual de usuario

Dejero

Dejero EnGo 3x Manual de usuario

Rosemount

Rosemount 4600 Manual de usuario

Speaka Professional

Speaka Professional 2342740 Manual de usuario

trubomat

trubomat GAB 1000 Manual de usuario

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manual de usuario

Rondish

Rondish UT-11 Manual de usuario

MG 10JRE Manual de usuario

Burkert

Burkert 8177 Manual de usuario

Firetide

Firetide HotPort 3203 Manual

Tele Radio

Tele Radio T9-02 Manual de usuario

Rotronic

Rotronic HygroFlex HF3 Series Manual de usuario

Jamara

Jamara FCX6 Pro Tel Manual de usuario